Motorcycle User Manual
Table Of Contents
- R1 EXUP DELTABOX V YZFR1X(C) OWNER'S MANUAL
- INTRODUCTION
- IMPORTANT MANUAL INFORMATION
- TABLE OF CONTENTS
- SAFETY INFORMATION
- DESCRIPTION
- INSTRUMENT AND CONTROL FUNCTIONS
- Main switch/steering lock
- Indicator and warning lights
- Multi-function meter unit
- Handlebar switches
- Clutch lever
- Shift pedal
- Brake lever
- Brake pedal
- Fuel tank cap
- Fuel
- Catalytic converters
- Seats
- Helmet holders
- Adjusting the front fork
- Adjusting the shock absorber assembly
- Luggage strap holders
- EXUP system
- Sidestand
- Ignition circuit cut-off system
- PRE-OPERATION CHECKS
- OPERATION AND IMPORTANT RIDING POINTS
- PERIODIC MAINTENANCE AND MINOR REPAIR
- PERIODIC MAINTENANCE
- Owner's tool kit
- Periodic maintenance chart for the emission control system
- General maintenance and lubrication chart
- Removing and installing cowlings and panels
- Checking the spark plugs
- Canister (for California only)
- Engine oil and oil filter cartridge
- Coolant
- Checking and replacing the air filter element
- Checking the engine idling speed
- Checking the throttle cable free play
- Valve clearance
- Tires
- Cast wheels
- Accessories and replacement parts
- Adjusting the clutch lever free play
- Adjusting the rear brake light switch
- Checking the front and rear brake pads
- Checking the brake fluid level
- Changing the brake fluid
- Drive chain slack
- Cleaning and lubricating the drive chain
- Checking and lubricating the cables
- Checking and lubricating the throttle grip and cable
- Checking and lubricating the brake and clutch levers
- Checking and lubricating the shift pedal
- Checking and lubricating the sidestand
- Lubricating the swingarm pivots
- Checking the front fork
- Checking the steering
- Checking the wheel bearings
- Battery
- Replacing the fuses
- Replacing a headlight bulb
- Tail/brake light
- Replacing a turn signal light bulb
- Replacing the license plate light bulb
- Replacing an auxiliary light bulb
- Supporting the motorcycle
- Front wheel
- Rear wheel
- Troubleshooting
- Troubleshooting charts
- MOTORCYCLE CARE AND STORAGE
- SPECIFICATIONS
- CONSUMER INFORMATION
- INDEX
![](/manual/yamaha/lit-11626-21-41/motorcycle-user-manual/images/img-99.png)
MOTORCYCLE CARE AND STORAGE
7-2
7
with mild detergent, alkaline
products and a soft brush may
be used.
● Do not use any harsh chemical
products on plastic parts or the
mufflers. Be sure to avoid using
cloths or sponges which have
been in contact with strong or
abrasive cleaning products, sol-
vent or thinner, fuel (gasoline),
rust removers or inhibitors,
brake fluid, antifreeze or electro-
lyte.
● Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
storage compartments, electric
components (couplers, connec-
tors, instruments, switches and
lights), breather hoses and
vents.
● For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.
NOTE:
Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
engine has cooled down.
CAUTION:
ECA10790
Do not use warm water since it in-
creases the corrosive action of the
salt.
2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces (except the tita-
nium mufflers) to prevent
corrosion.
Cleaning the titanium mufflers
This model is equipped with titanium
mufflers, which require the following
special care.
● Use only a soft, clean cloth or
sponge with mild detergent and
water to clean the titanium muf-
flers. However, if the mufflers can-
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM