URTG LPX-510 Home Cinema Projector ENGLISH OWNER'S MANUAL
LPX-510_E.book Page i Wednesday, January 21, 2004 10:58 AM IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
LPX-510_E.book Page ii Wednesday, January 21, 2004 10:58 AM COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Electronics Corporation 6660 Orangethorpe Avenue Buena Park, CA90620 714-522-9105 714-670-0108 Projector LPX-510 This device complies with Part 15 of the FCC Rules.
LPX-510_E.book Page iii Wednesday, January 21, 2004 10:58 AM Caution: Read this before operating this unit. • To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Installation • • • • • • Install this unit in a well-ventilated, cool, dry, clean place with at least 10 cm clearance on the top, right and left, and at the back of this unit — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.
LPX-510_E.book Page 0 Wednesday, January 21, 2004 10:58 AM OBSERVERA Apparaten kopplas inte bort från växelströmskällan (nätet) så länge som den är ansluten till vägguttaget, även om själva apparaten har stängts av. ADVARSEL Alleen voor klanten in Nederland Bij dit product zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.
LPX-510_E.book Page 1 Wednesday, January 21, 2004 10:58 AM Turning On the Projector....................................................................................6 Connecting the Power Cord ..................................................................................... 6 Turning On the Power and Projecting Images.......................................................... 7 Turning Off the Projector....................................................................................
LPX-510_E.book Page 2 Wednesday, January 21, 2004 10:58 AM Notes on Handling and Storage Be sure to observe the following precautions to avoid malfunctions, operating errors or damage to the projector. Notes on Handling and Storage • Do not set up the projector near high-voltage electrical wires or sources of magnetic fields. These may interfere with correct operation. • Do not touch the lens with bare hands.
LPX-510_E.
LPX-510_E.book Page 4 Wednesday, January 21, 2004 10:58 AM Features of the Projector Image appearance can be selected to match the projection environment (Picture Mode) The projector is equipped with a unique CB (color balance) filter that enhances the color reproduction of images. It is ideal for use in providing the optimum image effects for the projection environment when viewing images such as games, sporting competitions and movies. It makes other troublesome color adjustments unnecessary. (p.
LPX-510_E.book Page 5 Wednesday, January 21, 2004 10:58 AM Basic Operations This chapter describes basic operations such as turning the projector on and off and adjusting the projected images. Turning On the Projector .................................................................. 6 • • Connecting the Power Cord ........................................................................................6 Turning On the Power and Projecting Images ..........................................................
LPX-510_E.book Page 6 Wednesday, January 21, 2004 10:58 AM Turning On the Projector This section describes the procedure from turning on the power to projecting images. Be sure to read the Safety Instructions in this manual for details on safe handling when using the projector. Connecting the Power Cord 1 Check that the power is turned off for all components connected to the projector. 2 Connect the computer or other video source to the projector. Refer to the Setup Guide. 3 Remove the lens cap.
LPX-510_E.book Page 7 Wednesday, January 21, 2004 10:58 AM Turning On the Projector Turning On the Power and Projecting Images 1 2 Lights green STANDBY/ON ESCAPE MENU IRIS PATTERN ZOOM FOCUS SETTING PATT SETTING MENU ESCAPE ASPECT INPUT Projector Basic Operations Turn on the power for all equipment connected to the projector. For a video source, press the [Play] button at the video source to start playback.
LPX-510_E.book Page 8 Wednesday, January 21, 2004 10:58 AM Turning On the Projector • If only one signal source has been connected, the signals from that source will be projected without needing to press one of the above buttons. • If video signals are being input to several input ports simultaneously, interference between the various signals may occur, and this may cause interference in the projected images.
LPX-510_E.book Page 9 Wednesday, January 21, 2004 10:58 AM Turning Off the Projector Follow the procedure below to turn off the power of the projector. 1 Turn off the power for the signal sources that are connected to the projector. Check that the power for all connected components has been tuned off.
LPX-510_E.book Page 10 Wednesday, January 21, 2004 10:58 AM Turning Off the Projector 5 Retract the front adjustable foot if it is extended. Turn the front adjustable foot to retract it. Retract 6 7 10 Retract Attach the lens cap. Attach the lens cap to the lens when not using the projector, in order to stop the lens from getting dusty or dirty. Disconnect the cords that are connecting the projector and other equipment.
LPX-510_E.book Page 11 Wednesday, January 21, 2004 10:58 AM Adjusting the Screen Image You can adjust the screen image in order to obtain the best possible picture. Adjusting the Image Size (Zoom adjustment) The size of the projected image is basically determined by the distance from the projector to the screen. (Refer to the Setup Guide.) The following procedures explain how to adjust the screen image once the projector itself has been set up.
LPX-510_E.book Page 12 Wednesday, January 21, 2004 10:58 AM Adjusting the Screen Image Projection image position adjustment (Lens shift) The lens shift function can be used to adjust the position of projected images when the projector has been set up in places such as the following.
LPX-510_E.book Page 13 Wednesday, January 21, 2004 10:58 AM Adjusting the Screen Image Correcting Keystone Distortion (Keystone) When you wish to adjust the projection above or below the range of lens shift adjustment set the projector at an angle. When the projector is angled, the projected image may distort into a trapezoid. Keystone distortion can be corrected within a maximum vertical angle of approximately 15°. Approx. 15°° above Basic Operations Approx.
LPX-510_E.book Page 14 Wednesday, January 21, 2004 10:58 AM Adjusting the Screen Image Displaying a Test Pattern You can project a test pattern at times such as when setting up the projector in order to correct keystone correction and to make line menu adjustments. • Crosshatch This can be used to check whether the projector is tilted or set up vertically in front of the screen. • Grayscale pattern This is used when adjusting brightness or when adjusting image quality or color tone.
LPX-510_E.book Page 15 Wednesday, January 21, 2004 10:58 AM Adjusting the Screen Image 4 STANDBY/ON ESCAPE IRIS SETTING PATT ESCAPE MENU ASPECT INPUT MENU PATTERN SETTING ASPECT Exit the pattern display. Display the pattern select menu and then select "Exit". Press the button on the projector's control panel or the button on the remote control. INPUT LIGHT Projector HIDE Remote control Basic Operations The full menu cannot be displayed while a test pattern is being projected.
LPX-510_E.book Page 16 Wednesday, January 21, 2004 10:58 AM Adjusting the Image Quality The quality of the screen images can be adjusted as follows. Focus adjustment 1 STANDBY/ON ESCAPE MENU IRIS PATTERN ZOOM FOCUS SETTING PATT SETTING MENU ESCAPE ASPECT Press the [SETTING] button on the projector's control panel or the FOCUS button on the remote control. An adjustment icon will be displayed over the image during projection.
LPX-510_E.book Page 17 Wednesday, January 21, 2004 10:58 AM Adjusting the Image Quality Brightness adjustment (Iris adjustment) The brightness of the images can be adjusted. When projecting in dark rooms or onto small screens and the images appear too bright, decrease the setting. STANDBY/ON ESCAPE MENU IRIS PATTERN ZOOM FOCUS SETTING PATT SETTING MENU ESCAPE ASPECT Press the [SETTING] button on the projector's control panel or the IRIS button on the remote control.
LPX-510_E.book Page 18 Wednesday, January 21, 2004 10:58 AM Adjusting the Image Quality Selecting the picture mode The following six picture modes have been preset for use with images with varying characteristics. Use the select menu to select a picture mode that best suits the images. Mode name Use Dynamic Ideal for viewing games and sporting competitions in bright rooms. Bright Ideal for viewing movies in bright rooms. Standard Ideal for viewing in dark rooms.
LPX-510_E.book Page 19 Wednesday, January 21, 2004 10:58 AM Adjusting the Image Quality Selecting the Image Aspect Ratio This selects the ratio between the height and width of the projected images. If the input signal includes aspect ratio information, the projector's automatic mode will detect this information and use it to automatically change the aspect ratio to the optimum ratio. • Basic Operations Automatic mode can only be set when signals are being input to the VIDEO, S VIDEO, D4 or HDMI port.
LPX-510_E.book Page 20 Wednesday, January 21, 2004 10:58 AM Adjusting the Image Quality Details of each aspect ratio are as follows. Normal mode 4:3 image The aspect ratio of the images being input is maintained, and the images are projected into a 16:9 screen area. If projecting images in 4:3 mode such as normal TV broadcasts and computer images, black bands will be displayed at the left and right as shown in the illustration at left.
LPX-510_E.book Page 21 Wednesday, January 21, 2004 10:58 AM Adjusting the Image Quality Smart Zoom mode 4:3 image Basic Operations Images in 4:3 format such as normal TV broadcasts are extended horizontally, with less elongation in the middle and more elongation at the edges. This is useful for when 4:3 images are projected onto a wide screen. Because there is almost no distortion due to enlargement in the middle of the images, the images appear close to what they would be at their original size.
LPX-510_E.book Page 23 Wednesday, January 21, 2004 10:58 AM Advanced Operations This chapter describes functions for enhancing the projection of images, and how to use the menus. Functions for Enhancing Projection ............................................. 24 • Description of Functions ............................................................................................24 • White Level Adjustment ...................................................................................................
LPX-510_E.book Page 24 Wednesday, January 21, 2004 10:58 AM Functions for Enhancing Projection This section explains how to use the functions for adjusting the picture quality to the optimum quality. Description of Functions White Level Adjustment Adjusts the brightness of bright shades without changing the black level. Use the "Image" - "Picture Quality" - "Input Adjustment" - "White Level/Black Level" - "White Level" menu item to change the setting. (p.
LPX-510_E.book Page 25 Wednesday, January 21, 2004 10:58 AM Functions for Enhancing Projection Absolute Color Temperature and Flesh Tone Adjustment The absolute color temperature adjusts the tint of the whole image. Flesh tone adjustment adjusts the color of flesh tones to the desired color. Use the "Image" - "Color Adjustment" - "Abs. Color Temp." and "Flesh Tone" menu items to change the settings. (p.31) Change in color temperature • Abs. Color Temp.
LPX-510_E.book Page 26 Wednesday, January 21, 2004 10:58 AM Functions for Enhancing Projection Saving and Retrieving Image Quality Settings (Memory Save) Once the "Picture Quality" and "Color Adjustment" menu commands have been used to adjust the projected images, the adjustment values can then be stored. In addition, the saved data can be retrieved easily, so that you can enjoy viewing images with the adjusted settings at any time. Settings that can be saved in memory • menus (p.
LPX-510_E.book Page 27 Wednesday, January 21, 2004 10:58 AM Functions for Enhancing Projection Image Setup Info Select "Memory Save" from the submenu of the "Image" menu, and then press the button on the projector's control panel or the button on the remote control.
LPX-510_E.book Page 28 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions The menus can be used to make adjustments and settings for items such as the screen, image quality and input signal. The following two types of menu are available. • • Full menu This lets you check all menu items while making settings.
LPX-510_E.book Page 29 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions indicates default settings "Setup" menu Signal Progressive p.32 OFF, Video, Film/Auto Motion Detection Median value (3) Noise Reduction OFF , NR1, NR2 Overscan When component video or RGB video signals are input: Standard , Full When component video signals or RGB video signals are being input to the HDMI port: Auto , Standard, Larger Setup Level (Varies depending on country of purchase) 0% , 7.
LPX-510_E.book Page 30 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions "Image" Menu The image quality adjustment items are determined by the input port (image signal) that is selected.
LPX-510_E.book Page 31 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions Color Adjustment If the picture mode is set to "PC", "Color Adjustment" cannot be selected. Main menu Abs. Color Temp. *2 Function • Abs. Color Temp. : This adjusts the overall tints of the images in accordance with the images being projected. (p.25) • Flesh Tone RGB *1 : This adjusts the flesh tones of people who appear in the images. (p.
LPX-510_E.book Page 32 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions "Setup" Menu Image Setup Info Reset Return Signal Screen Operation User's Logo On-Screen Display Input Signal Language Reset -,+:Select English :Enter Signal Main menu Function Progressive *1 (Setting is only possible when composite video , S-Video , component video or 480i and 576i RGB video signals are being input.
LPX-510_E.book Page 33 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions Main menu Default setting Function Setup Level *1 (Setting is only possible when composite video or S-Video signals in NTSC format are being input or component video has been set. Setting is not possible when signals are being input from the HDMI port.
LPX-510_E.book Page 34 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions Operation Main menu Function Sleep Mode The projector is equipped with a power-saving function that causes the power to turn off automatically and the projector to switch to standby if no signal is input to the projector for a continuous length of time. The length of time before the power-saving function operates can be selected from four available settings.
LPX-510_E.book Page 35 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions User’s Logo You can record your favorite image as a user's logo. A user's logo can be stored for projecting when the projector starts up and when projecting the hide screen. When a user's logo is recorded, the previous user's logo will be erased. Follow the instructions on the screen to record a user ’s logo.
LPX-510_E.book Page 36 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions Input Signal Main menu Function Default setting Video Signal Sets the signal format in accordance with the video equipment that is connected to the VIDEO or S VIDEO port. If set to "Auto", the video signal format is set automatically. If there is a lot of interference in the image, or if a problem such as no image being projected occurs even though "Auto" has been selected, select the correct signal format manually.
LPX-510_E.book Page 37 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions Using the Menus Displaying and Operating Full Menus Menus can be operated using the projector's control panel and also by using the remote control. 1 STANDBY/ON IRIS SETTING ESCAPE PATT MENU ESCAPE MENU Display the menu screen. Press the [MENU] button on the projector's control panel or the button on the remote control.
LPX-510_E.book Page 38 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions 4 Setup Image Info Change the setting. If using the projector's control panel, press the − or + button to make the setting. If using the remote control, tilt the button to the left or right. If a selection menu is displayed, select an item, and then press the button on the projector's control panel or the button on the remote control to confirm the setting.
LPX-510_E.book Page 39 Wednesday, January 21, 2004 10:58 AM Using the Menu Functions 2 STANDBY/ON ESCAPE IRIS SETTING PATT ESCAPE MENU ASPECT INPUT MENU PATTERN SETTING ASPECT INPUT LIGHT Projector HIDE Remote control Select an item to be set. If using the projector's control panel, press the or button to select a command. If using the remote control, tilt the button up or down to select a command. The line menu item changes when a button is pressed.
LPX-510_E.book Page 41 Wednesday, January 21, 2004 10:58 AM Troubleshooting This chapter describes troubleshooting procedures for the projector. When Having Some Trouble ........................................................... 42 When the Indicators Provide No Help ........................................... 44 • Problems relating to images .................................................................................................... 44 • Problems when projection starts .......................
LPX-510_E.book Page 42 Wednesday, January 21, 2004 10:58 AM When Having Some Trouble The projector is provided with the following three indicators which notify you of the operating status of the projector. The following tables show what the indicators mean and how to remedy the problems that they indicate. *If the indicator does not light when the power is turned on, the power cord may not be connected correctly or the power may not be supplied.
LPX-510_E.book Page 43 Wednesday, January 21, 2004 10:58 AM When Having Some Trouble Indicator status Orange Projector status (No abnormality) If you press the [STANDBY/ON] button on the projector's control panel or the button on the remote control, projection will start after the warm-up is complete. p.6 Warm-up in progress (No abnormality) The warm-up period is approximately 30 seconds. Wait for short while. The indicator will stop flashing and light green.
LPX-510_E.book Page 44 Wednesday, January 21, 2004 10:58 AM When the Indicators Provide No Help If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem. Probable relating to images No images appear Projection does not start, the projection area is completely black, the projection area is completely blue, etc. See below The message "Not Supported." is displayed (p.45) The message "No Signal." is displayed (p.
LPX-510_E.book Page 45 Wednesday, January 21, 2004 10:58 AM When the Indicators Provide No Help The message "Not Supported." is displayed Are the image signal format settings correct? When a composite video or S-Video signal is being input. If images cannot be projected even when the "Video Signal" menu command is set to "Auto", change the setting to the signal format for the connected equipment. "Setup" - "Input Signal" - "Video Signal" (p.
LPX-510_E.book Page 46 Wednesday, January 21, 2004 10:58 AM When the Indicators Provide No Help Interference or distortion appear in images Are the image signal format settings correct? When a composite video or S-Video signal is being input. If images cannot be projected even when the "Video Signal" menu command is set to "Auto", change the setting to the signal format for the connected equipment. "Setup" - "Input Signal" - "Video Signal" (p.
LPX-510_E.book Page 47 Wednesday, January 21, 2004 10:58 AM When the Indicators Provide No Help Image colors are not right Are the image signal format settings correct? When a composite video or S-Video signal is being input. If images cannot be projected even when the "Video Signal" menu command is set to "Auto", change the setting to the signal format for the connected equipment. "Setup" - "Input Signal" - "Video Signal" (p.
LPX-510_E.book Page 48 Wednesday, January 21, 2004 10:58 AM When the Indicators Provide No Help Problems when projection starts Power does not turn on Have you pressed the [Power] button? Press the button on the remote control or the [STANDBY/ ON] button on the projector's control panel. Is "Key Lock" set to "ON"? If the "Key Lock" menu command is set to "ON", none of the control panel buttons will operate. Press the button on the remote control. "Setup" - "Operation" - "Lock Setting" - "Key Lock" (p.
LPX-510_E.book Page 49 Wednesday, January 21, 2004 10:58 AM Appendices This chapter provides information on maintenance procedures to ensure the best level of performance for the projector for a long time. Maintenance..................................................................................... 50 • Cleaning.......................................................................................................................50 • Cleaning the Projector Case .........................................
LPX-510_E.book Page 50 Wednesday, January 21, 2004 10:58 AM Maintenance This section describes maintenance tasks such as cleaning the projector and replacing consumable parts. Cleaning You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate. Be sure to read the Safety Instructions in this manual for details on safe handling of the projector during cleaning. Cleaning the Projector Case Clean the projector case by wiping it gently with a soft cloth.
LPX-510_E.book Page 51 Wednesday, January 21, 2004 10:58 AM Maintenance Cleaning the Air Filter If the airfilter becomes clogged with dust or the message "The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air filter." is displayed, clean the air filter. Turn the projector upside-down and use a vacuum cleaner to clean the air filter. * Do not use water or detergents to clean the air filter.
LPX-510_E.book Page 52 Wednesday, January 21, 2004 10:58 AM Maintenance 4 Install the air filter. Install the air filter so that it faces the correct way. 5 Install the air filter cover. Replacing Consumables This section explains how to replace the lamp. Lamp Replacement Period It is time to replace the lamp when: • The message "Lamp Replace" appears on the screen when projection starts. The message appears for 30 seconds, and disappears again after 30 seconds have passed.
LPX-510_E.book Page 53 Wednesday, January 21, 2004 10:58 AM Maintenance • The lamp replacement warning message is set to appear after approximately 1600 hours of lamp use in order to maintain the brightness and quality of the projected images. The time taken for the message to be displayed will vary depending on factors such as the lamp power setting and the picture mode setting. If you continue to use the lamp after this period, the possibility of the lamp breaking becomes greater.
LPX-510_E.book Page 54 Wednesday, January 21, 2004 10:58 AM Maintenance 4 Loosen the screws fixing the lamp. 5 Remove the old lamp. Pull the lamp out straight. 6 Install the new lamp. Securely insert the lamp so that it is facing correctly. 7 Securely tighten the lamp fixing screws. 8 Install the lamp cover, then tighten the lamp cover fixing screws. • • 54 Install the lamp securely. For safety, the lamp will turn off automatically when the lamp cover is opened.
LPX-510_E.book Page 55 Wednesday, January 21, 2004 10:58 AM Maintenance Resetting the Lamp Operating Time The lamp operating time must always be reset after the lamp has been replaced with a new one.The projector has a built-in lamp operating time counter. A replacement message is displayed when the counter reaches a certain amount. Do not reset the lamp operating time except after the lamp has been replaced, otherwise the lamp replacement period will not be indicated correctly.
LPX-510_E.book Page 56 Wednesday, January 21, 2004 10:58 AM Maintenance If vertical stripe interference appears in the projected images Vertical stripe interference may appear in the projected images at times. If this vertical stripe interference impairs image viewing, the images can be adjusted by carrying out the following procedure. Example Image with vertical stripe interference Image after adjustment Note the following points when carrying out the procedure below.
LPX-510_E.book Page 57 Wednesday, January 21, 2004 10:58 AM Maintenance 3 Dark portions Bright portions Apply [Vertical Stripe Adjustment R] Bright Color 0 Dark Color 0 ESC :Return :Select -,+:Adjust 4 While checking the tone adjustment screen, adjust the settings starting from the one where the vertical stripe interference is most noticeable. If the stripes are most noticeable in the bright portions of the image, adjust the "Bright Color" setting first.
LPX-510_E.book Page 58 Wednesday, January 21, 2004 10:58 AM Optional Accessories The following options are available for using with the projector. The availability of these options is subject to change without prior notice. Lamp cartridge PJL-520 Use as a replacement for spent lamps. Ceiling mount bracket (for low ceilings) * PMT-L51 Use when installing the projector to a low ceiling. Ceiling mount bracket (for high ceilings) * PMT-H55 Use when installing the projector to a high ceiling.
LPX-510_E.book Page 59 Wednesday, January 21, 2004 10:58 AM List of Supported Signal Resolutions Depending on the "Overscan"settings, the values given below will change slightly.
LPX-510_E.
LPX510_E_4.FM Page 61 Tuesday, February 10, 2004 1:54 PM Specifications Product name LPX-510 Home cinema projector Dimensions 440 (W) x 137 (H) x 321 (D) mm (17.3 (W) x 5.39 (H) x 12.6 (D) inches) (not including protruding parts) Panel size 17.8mm (0.7 inches) Display method Polysilicon TFT active matrix Drive method Full-line 12-phase block sequential writing Resolution 921,600 pixels (1280 (W) x 720 (H) dots) x 3 Focus adjustment Electronic type Zoom adjustment Electronic type (approx.
LPX-510_E.book Page 62 Wednesday, January 21, 2004 10:58 AM UP 440 LAMP/COVER TEMP/FAN HOME CINEMA PROJECTOR LPX-510 ASPECT LENS SIFT DOWN 80 ESCAPE Center of projector PATTERN STANDBY/ON INPUT MENU SETTING Appearance 19.5 68 LEFT RIGHT Surface of lens Center of lens 19.7 321 156.5 137 87.
LPX-510_E.book Page 63 Wednesday, January 21, 2004 10:58 AM Part Names and Functions Front/Top Control panel (p.64) Vertical lens adjustment dial (p.12) Moves the lens vertically. Horizontal lens adjustment dial (p.12) Moves the lens horizontally. Remote control light-receiving area (Setup Guide) Receives signals from the remote control. Lens cap Attach when not using the projector to prevent the lens from becoming dirty or damaged. Air exhaust vent Front adjustable feet (p.
LPX-510_E.book Page 64 Wednesday, January 21, 2004 10:58 AM Part Names and Functions Control Panel STANDBY/ON ESCAPE MENU PATTERN SETTING ASPECT INPUT LAMP/COVER TEMP/FAN HOME CINEMA PROJECTOR LPX- 510 [STANDBY/ON] button (p.7, 9) Press to turn the projector's power on and off. [ESCAPE] button (p.11, 16, 17, 38, 39) When pressed while a menu or selection menu is being displayed, the screen changes to the previously-displayed menu. [PATTERN] button (p.
LPX-510_E.book Page 65 Wednesday, January 21, 2004 10:58 AM Part Names and Functions Rear G/Y B / PE:/C E: R/ PR:/C R: HD/SYNC VD G/Y B / PE:/C E: R/ PR:/C R: HD/SYNC VD INPUT A HDMI VIDEO D4 VIDEO S VIDEO INPUT B RS-232C D4 VIDEO port (Setup Guide) Connects to the component video ports or D port of other video equipment. (Japan only) INPUT A/INPUT B ports (Setup Guide) Connects to the component video ports or RGB ports of other video equipment or to a computer's video output port.
LPX-510_E.book Page 66 Wednesday, January 21, 2004 10:58 AM Part Names and Functions Remote Control IRIS ZOOM FOCUS SETTING PATT ESCAPE MENU ASPECT INPUT LIGHT HIDE S VIDEO A HDMI VIDEO B D4 INPUT MEMORY 1 2 3 4 5 6 Indicator Illuminates when remote control signals are being output. [PATT] button (p.14) Displays a selection menu for selecting a test pattern. [Zoom] button (p.11) Press to adjust the size of projected images. [MENU] button (p.
LPX-510_E.book Page 67 Wednesday, January 21, 2004 10:58 AM Glossary Component video Video signals which have the video brightness signals and color signals separated, in order to provide better image quality. In high-definition TV (HDTV), it refers to images which consist of three independent signals: Y (luminance signal), and Pb and Pr (color difference signals). Composite video Video signals which have the video brightness signals and color signals mixed together.
LPX-510_E.book Page 68 Wednesday, January 21, 2004 10:58 AM Glossary 68 Sync. (Synchronization) The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images will not be of a good quality. The process of matching the phases of these signals (the relative position of the crests and troughs in the signal) is called "synchronization".
LPX-510_E.book Page 69 Wednesday, January 21, 2004 10:58 AM All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of YAMAHA CORPORATION. No patent liability is assumed with respect to the use of the information contained herein.
©2004 YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD.
LPX510 SET UP GUIDE English-conver1 Home Cinema Projector LPX-510 ENGLISH 1 Before Using the Remote Control 2 Setup 3 Connecting to a home theater system 4 Connecting to a Computer Inserting the batteries and replacement period Using the remote control and remote operating range Screen Size and Setting-up Distance Setting-up Methods
LPX510 SET UP GUIDE English-01 1 Inserting the batteries and replacement period Before Using the Remote Control The batteries are not inserted into the remote control at the time of purchase. You will first need to insert the accessory batteries into the remote control. Remove the battery compartment cover. While pushing the catch, lift the battery cover up. 1 3 2 Insert the batteries. Make sure the polarities of the batteries are correct. Replace the battery compartment cover.
LPX510 SET UP GUIDE English-02 Using the remote control and remote operating range [LIGHT] (illumination) switch [LIGHT] switch When the [LIGHT] switch is tilted up or down, the buttons with indicators shown in the illustration at left will light for approximately 10 seconds. If the [LIGHT] switch is tilted up or down while the buttons are lit, they will stay lit for a further 10 seconds. Use the remote control within the ranges indicated below.
LPX510 SET UP GUIDE English-03 2 Screen Size and Setting-up Distance Setup The projection size will vary depending on the projection distance from the projector's lens to the screen. 90˚ The height from the center of the lens to the bottom of the screen will vary depending on the lens shift setting. Center of the lens Screen Projection distance Refer to the table below to the projector so that the images are projected onto the screen at the optimum size. Units: cm (in.
LPX510 SET UP GUIDE English-04 Setting-up Methods The projector supports the following 4 projection methods, allowing you to choose the best method for displaying your images. After setting up the projector, refer to the OWNER'S MANUAL for details on turning on the power and adjusting settings such as the screen size. ("Basic Operations" in OWNER'S MANUAL) Be sure to read "Caution" in OWNER'S MANUAL for details on safe handling when setting up the projector.
LPX510 SET UP GUIDE English-05 Turn off the power for the projector and the home theater system before making the connections. Check the shapes of the cable connectors and the device ports before making the connections. If you try to force a connector to fit a device port with a different shape or number of terminals, a malfunction or damage to the connector or port may result.
LPX510 SET UP GUIDE English-06 4 Connecting to a Computer Turn off the power for both the projector and the computer before connecting them. If the power for either device is on at the time of connection, damage may result. Check the shapes of the cable connectors and the device ports before making the connections. If you try to force a connector to fit a device port with a different shape or number of terminals, damage to the connector or port may result.
LPX510 SET UP GUIDE English-07 Computer DVI Computer cable (commerciallyavailable) + BNC RCA adapter connector HDMI cable (commerciallyavailable) (commerciallyavailable) * Attach the adapter connector to the computer cable and then connect it to the projector. G/Y B / PB/CB R/ PR/CR HD/SYNC VD INPUT A HDMI VIDEO D4 VIDEO S VIDEO INPUT B G/Y B / PB/CB R/ PR/CR HD/SYNC VD RS-232C *Push the connectors in as far as they will go. ©2004 All Rights Reserved.
