User Manual
M7CL V3 Editor Owner’s Manual
23
E
MATRIX SEND
These bar graphs indicate the send levels of the signals sent from the MIX
channel to MATRIX 1–8 bus. You can also adjust the send levels by drag-
ging a bar graph to left or right. While you drag the bar graph, the send
level is shown in the numerical display area for TO STEREO/MONO.
You can set the minimum value (–
∞
dB) by holding down the
<Ctrl>(< >) key of your computer keyboard and clicking the bar
graph, or set the nominal value (0.00 dB) by holding down the
<Ctrl>(< >) key and <Shift> key and clicking the bar graph.
The bar graph display will change as follows according to the send position (pre/post)
and on/off status of the signal sent from the MIX channel to the MATRIX buses.
To switch a send on/off, click the channel number located at the left of the bar graph.
F
PAN/BALANCE
The
PAN knob
adjusts the panning of the signal that is sent from the mix channel to the
STEREO bus L/R channels (or the L/C/R channels). You can set this to the center value
by holding down the <Ctrl>(< >) key of your computer keyboard and clicking this
knob. If assigned as a stereo bus, this adjusts the balance of the odd-numbered channel
and even-numbered channel. The stereo bus setting can be made in Mix Bus Setup of
the Mixer Setup dialogbox.
The
[ST] button
is an on/off switch for the signal that is sent from the mix channel to
the STEREO bus.
The
[MONO] button
is an on/off switch for the signal that is sent from the mix channel
to the MONO bus.
If LCR MODE is selected in the Selected Channel window, the
[LCR]
button will
appear instead of the [ST] button and [MONO] button, and the [LCR] button will be
an on/off switch for the signal that is sent from the mix channel to the LCR bus.
G
VARI/FIXED
Indicates the type (VARI or FIXED) of the currently selected MIX bus. This parameter
can be switched in Mix Bus Setup of the Mixer Setup dialogbox.
H
SEL (Select)
Selects the MIX channel for which you want to make settings.
I
CUE
This button cue-monitors the signal of the MIX channel.
J
ON
Switches the MIX channel on/off.
The button is color-coded and indicates status as follows:
White: MIX channel is on (normal mode).
Black: MIX channel/Send is off.
Other colors: Send is on (SENDS ON FADER mode).
K
Fader
Adjusts the output level of the MIX
channel. The current fader value is
shown in the numeric box immediately
below the fader. You can set this to the
minimum value (–∞ dB) by holding
down the
<Ctrl>(< >) key
of your
computer keyboard and clicking the
fader knob, or set it to the nominal value
(0.00 dB) by holding down the
<Ctrl>(< >) key
and <Shift> key and
clicking the fader knob.
The numbers and alphabetical letters at
the right of the fader indicate the mute
groups to which that channel belongs, and show the Recall Safe and Mute Safe status of
the channel.
The fader is color-coded and indicates status as follows:
White: You can adjust the input level of the MIX channel (normal mode).
Gray: MIX channel is off.
Other colors: You can adjust the send level (SENDS ON FADER mode).
6
5
8
9
J
L
M
7
K
• Pre/on (green))
• Pre/off (green)
• Post/on (yellow)
• Post/off (yellow)
The numbers of mute groups
to which this channel belongs
are shown in red.
If this channel is set to Recall
Safe, the R character is
shown in green.
If this channel is set to Mute
Safe, the M character is
shown in green.