User Manual

ManualsBrandsYamaha ManualsMixing TablesDigital mixing desk

M7CL ﬁrmware V1.10 contains the following changes and additions relative to

V1.05. (Changes in V1.06 are also included here.)

* The Help function in V1.10 and later of this product uses bitmap fonts from the Ricoh Corporation.

• Speed of synchronization with M7CL Editor has been

improved.

• In the ATT/HPF/EQ popup window (1ch) and the

DYNAMICS popup window (1ch), the location of the

ON button has been distanced from the “ × ” (close) but-

ton in order to prevent accidental operation.

• By pressing a GEQ fader in the GEQ popup window,

you can now switch the faders assigned to the Central-

ogic section. The numbers of the assigned faders are

shown on the GEQ faders.

• The position of the window has been improved so that

the channel number and channel name ﬁeld at the bot-

tom of the display can be seen even when a popup win-

dow or the SCENE LIST window is displayed.

• When you use the SAVE/LOAD screen to save all of the

M7CL’s internal data (except for user authentication key

data) in a single operation, the user level, user-deﬁned

keys, and preference settings of the administrator and

guest will also be saved. On the M7CL console, this

data can be loaded only when the administrator logs in.

In M7CL Editor (V2.1.1 or later), this data can be read

at any time. However on earlier versions of the M7CL

console or M7CL Editor, this data that was saved in

V1.10 or later cannot be read.

•You can now view the M7CL’s Help by pressing the

(Help) button in the function access area. For

details, refer to “Using the Help function.”

• The assigned user-deﬁned key will now blink while

you’re viewing a screen or popup window that’s book-

marked by a user-deﬁned key.

•You can now reset the GAIN to the default value (0.0

dB) for each band by simultaneously pressing the

SELECTED CHANNEL section EQ [Q] encoder and

EQ [GAIN] encoder.

• The following have been added as parameters that can

be assigned to the user-deﬁned keys.

• PRE FADER (immediately before the fader) has been

added as a position for direct output from an INPUT

channel.

• If you’re using the M7CL V1.10, you must use V2.1.1

or later of M7CL Editor. You can download the most

recent version of M7CL Editor from the following web-

site.

http://www.yamahaproaudio.com/

M7CL V1.10 Supplementary Manual

Changes in V1.06

Changes in V1.10

FUNCTION

PARAME-

TER 1

PARAME-

TER 2

Description

SET BY

SEL

SET

[INSERT

ON]

—

By holding down this key

and pressing the [SEL] key

of a channel, that chan-

nel’s INSERT ON can be

switched on/off.

SET BY

SEL

SET

[DIRECT

OUT ON]

—

By holding down this key

and pressing the [SEL] key

of a channel, that chan-

nel’s DIRECT OUT ON

can be switched on/off.

HELP — —

Opens or closes the HELP

popup window. If you hold

down this key and operate

a panel controller (except

for the faders) or an on-

screen controller, the cor-

responding explanation

will appear.

Summary of content (4 pages)

PAGE 1
M7CL V1.10 Supplementary Manual M7CL firmware V1.10 contains the following changes and additions relative to V1.05. (Changes in V1.06 are also included here.) * The Help function in V1.10 and later of this product uses bitmap fonts from the Ricoh Corporation. Changes in V1.06 • Speed of synchronization with M7CL Editor has been improved.
PAGE 2
Using the Help function You can view the Help file provided by Yamaha, or you can view any desired text file created by a user. * We accept no responsibility for any damages that may occur as a result of using help files created by a third party other than Yamaha. ■ Loading a Help file from a USB storage device NOTE • The help file is not backed up in internal user memory. Each time you turn on the power, you must reload it from your USB storage device.
PAGE 3
■ Viewing Help 1 Before you proceed, load the help file or text file from your USB storage device. 2 In the function access area, press the (Help) button to access the HELP popup window. ■ Using user-defined keys to recall Help directly 1 Before you proceed, load the Help file from your USB storage device. 2 In the function access area, press the SETUP button to access the SETUP screen.
PAGE 4
5 Press the button corresponding to the user- Directly recalling the Help for a specific controller in the LCD screen 6 In the FUNCTION column, choose “HELP” 9 While holding down the user-defined key to defined key to which you want to assign the Help function. and press the OK button. 7 When you’ve finished assigning the func- tion to the user-defined key, press the “ × ” symbol to close the USER DEFINED KEYS page. 8 In the function access area, press the SETUP button to close the SETUP screen.