GUITAR EFFECTS PROCESSOR [PHONES Jack] The PHONES Jack (stereo mini) lets you practice or edit patches while monitoring the MAGICSTOMP’s sound output through a pair of headphones. (Output level/Impedance: –10dBm/150Ω) * Use the Volume Knob to adjust the volume. * Output is still delivered from the OUTPUT jack when a pair of headphones is connected to the PHONES jack. When monitoring through a pair of headphones, make sure you properly adjust the volume so as not to damage your hearing.
Deep Edit Any of the parameters in the currently selected patch can be edited. You can use this, along with the ability to select a different effect type, to create original patches. q Press the [STORE/EXIT] button. “PRESS[STORE]1sec” will appear on the lower half of the display. * If you press the [STORE/EXIT] button when a Preset Patch is selected, the corresponding User Patch number will automatically be selected as the destination patch number for storing.
r Rotate the knobs to edit their corresponding parameters. After viewing the parameters you want to edit, use the knobs located below the display to edit the parameters. If the knob’s position does not match the parameter’s value, you’ll need to rotate the knob until it matches the position that corresponds to the parameter value before you can change the setting (→ Owner’s Manual : page 14). ÿEDIT-PRM:03/07Ÿ ؇08.
Auto Feedback Reduction (AFR) Function The MAGICSTOMP is equipped with a highly sophisticated Auto Feedback Reduction function (AFR) to eliminate feedback (howling). * In this case, “Feedback” is when a specific frequency produced by the amplifier causes the guitar to resonate uncontrollably, creating a howling sound. The MAGICSTOMP’s AFR function uses a notch filter, which cuts the frequency that is causing the feedback, to eliminate feedback.
After selecting a patch in which the AFR function is active, follow the instructions below to use the AFR function. * The AFR function’s switch operation differs in the Up/Down Mode and Performance Mode. q When feedback occurs in the Up/Down Mode press the ON/OFF switch, and when in the Performance Mode press the switch that corresponds to the currently selected patch (–, ON/OFF, +).
GUITAR EFFECTS PROCESSOR Nouveautés et améliorations du modèle MK2 Français [Édition complète] La fonction « Édition complète » du modèle MK2 vous permet de modifier n’importe quel paramètre d’un patch, de définir les paramètres commandés par les trois potentiomètres de l’appareil, et de mémoriser ces réglages.
Édition complète (Deep Edit) N’importe quel paramètre du patch actuellement sélectionné peut être modifié. Vous pouvez employer cette possibilité, et le fait qu’un autre type d’effet puisse également être choisi, pour composer des patches originaux. q Appuyez sur le bouton [STORE/EXIT]. Le message “PRESS[STORE]1sec” apparaît sur la ligne du bas de l’afficheur.
r Tournez les boutons pour modifier les paramètres correspondants. Après avoir accédé aux paramètres à modifier, utilisez les boutons situés sous l’afficheur pour modifier les valeurs des paramètres. Si la position du bouton ne correspond pas à la valeur du paramètre, vous devez tourner le bouton jusqu’à ce que sa position corresponde à la valeur du paramètre, avant d’être en mesure de modifier la valeur du paramètre (→ Mode d’emploi : page 40). ÿEDIT-PRM:03/07Ÿ ؇08.
Fonction de réduction automatique des couplages (AFR) Le MAGICSTOMP est doté d’une fonction très performante de réduction des couplages permettant de supprimer l’effet Larsen (hurlement). * Le “couplage” se produit lorsqu’une fréquence donnée produite par l’amplificateur provoque une mise en résonance de la guitare jusqu’à créer un son puissant et désagréable ressemblant à un hurlement.
Après sélection d’un patch pour lequel la fonction AFR est active, suivez les instructions ci-dessous pour utiliser cette fonction. * Les commandes de la fonction AFR diffèrent selon que vous êtes en mode Avance/Recul ou en mode Performance. q Lorsque se produit un couplage tandis que l’appareil est en mode Avance/Recul, ou bien en mode Performance, appuyez sur le commutateur qui correspond au patch actuellement sélectionné (–, ON/OFF, +).
GUITAR EFFECTS PROCESSOR Was ist neu und besser im MK2? [Deep Edit] Die “Deep Edit”-Funktion des MK2 ermöglicht die Bearbeitung aller Parameter eines Patch-Programms, die Zuordnung von Parametern zu den drei Reglern und das Speichern der vorgenommenen Einstellungen. Beim früheren MAGICSTOMP war die umfassende Bearbeitung und die Zuordnung von Parametern nur mit dem Anwendungsprogramm “Sound Editor for MAGICSTOMP” auf einem Computer möglich.
Deep Edit In diesem Modus können alle Parameter des gegenwärtig gewählten Patch-Programms bearbeitet werden. Zusammen mit der Fähigkeit, einen anderen Effekttyp zu wählen, bietet Ihnen diese Funktion die Möglichkeit, eigene Patches zu programmieren. q Drücken Sie die [STORE/EXIT]-Taste. “PRESS[STORE]1sec” wird in der unteren Hälfte des Displays angezeigt.
r Bearbeiten Sie die Parameter, indem Sie die zugehörigen Regler verstellen. Sobald die zu bearbeitenden Parameter angezeigt werden, nehmen Sie die Einstellungen mit den zugehörigen Reglern unter dem Display vor. Sollte die aktuelle Reglerposition nicht mit dem angezeigten Parameterwert übereinstimmen, müssen Sie den Regler zunächst bis zu der Position verstellen, die Parameterwert entspricht, bevor Sie die Einstellung ändern können (→ Bedienungsanleitung : Seite 66). ÿEDIT-PRM:03/07Ÿ ؇08.
AFR-Funktion (Auto Feedback Reduction) Der MAGICSTOMP bietet eine hochentwickelte AFR-Funktion, die eine Unterdrückung problematischen Feedbacks (Heulen) ermöglicht. * Der Begriff “Feedback” bezieht sich hier auf den bei bestimmten Verstärkerfrequenzen auftretenden unkontrollierbaren Resonanzeffekt der Gitarre, durch den ein Heulgeräusch erzeugt wird. Die AFR-Funktion des MAGICSTOMP arbeitet mit einer Notch-Filterschaltung, die spezifische Störfrequenzen wegfiltert und so das Feedback beseitigt.
Nachdem Sie ein Patch mit aktivierter AFR-Funktion ausgewählt haben, folgen Sie zur Einrichtung den nachstehenden Anweisungen. * Die Bedienung der AFR-Funktion ist im UP/DOWN MODE und im PERFORMANCE MODE unterschiedlich. q Im UP/DOWN MODE drücken Sie beim Auftreten von Feedback den ON/OFF-Schalter, im PERFORMANCE MODE den Schalter (–, ON/OFF oder +), der dem gegenwärtig gewählten Patch zugeordnet ist.
GUITAR EFFECTS PROCESSOR Qué hay de nuevo y de mejorado en el MK2 [Edición profunda] La función de “Edición profunda” del MK2 le permite editar los parámetros de todos los efectos de los que consta el parche, ajustar los parámetros que se controlan con los tres mandos de control de la unidad, y guardar estos ajustes en la memoria. En el MAGICSTOMP original, toda la edición y la asignación de los mandos de control se efectuaba empleando un ordenador ejecutando la aplicación “Sound Editor for MAGICSTOMP”.
Edición profunda Podrá editar cualquier parámetro del parche actualmente seleccionado, Podrá emplear esta función, junto con la posibilidad de seleccionar un tipo de efecto distinto, para crear parches originales. q Presione el botón [STORE/EXIT]. Aparecerá “PRESS[STORE]1sec” en la mitad inferior del visualizador.
r Gire los mandos para editar sus parámetros correspondientes. Después de haber visto los parámetros que desea editar, emplee los mandos situados debajo del visualizador para editar los parámetros. Si la posición del mando no corresponde con el valor del parámetro, deberá girar el mando hasta que la posición corresponda con el valor del parámetro antes de poder cambiar el ajuste (→ Manual del usuario : página 92). ÿEDIT-PRM:03/07Ÿ ؇08.
Función de reducción automática de la realimentación (AFR) El MAGICSTOMP está provisto de una función muy sofisticada de reducción automática de la realimentación acústica (AFR) que elimine la realimentación (aullido). * En este caso, la “realimentación” se produce cuando una frecuencia específica producida por el amplificador hace que resuene la guitarra de forma descontrolada, creando un sonido de aullido.
Después de haber seleccionado un parche en el que la función AFR esté activada, siga las instrucciones siguientes para emplear la función AFR. * La operación del interruptor de la función AFR es distinta en el modo de incremento/reducción y en el modo de interpretación. q Cuando se produzca realimentación en el modo de incremento/reducción, presione el interruptor ON/OFF, y cuando ocurra en el modo de interpretación, presione el interruptor que corresponda al parche actualmente seleccionado (–, ON/OFF, +).
GUITAR EFFECTS PROCESSOR Cosa c’è di nuovo e di migliorato nell’MK2 [Deep Edit] La funzione “Deep Edit” dell’MK2 permette di editare tutti i parametri degli effetti che compongono un patch, impostare i parametri controllati dalle tre manopole dell’unità e salvare queste modifiche in memoria. Nel MAGICSTOMP originale, l’editing completo e l’assegnazione delle manopole di controllo veniva fatto con un computer e l’applicativo “Sound Editor for MAGICSTOMP”.
Deep Edit Qualsiasi parametro del patch correntemente selezionato può essere editato. Ciò può essere utilizzato, assieme alla capacità di selezionare un tipo di effetto diverso, per creare dei patch originali. q Premere il pulsante [STOR/EXIT]. L’indicazione “PRESS[STORE]1sec” appare nella metà inferiore del display.
r Ruotare le manopole per modificare i parametri corrispondenti. Dopo aver visto i parametri che si desidera editare, utilizzare le manopole sotto al display per modificare tali parametri. Se la posizione della manopola non corrisponde al valore del parametro, è necessario ruotare la manopola fino alla posizione corrispondente al valore del parametro prima di poter cambiare l’impostazione. (→ Manuale di istruzioni: pagina 118) ÿEDIT-PRM:03/07Ÿ ؇08.
Funzione Auto Feedback Reduction (AFR) Il MAGICSTOMP è fornito di una funzione Auto Feedback Reduction (AFR) estremamente sofisticata per l’eliminazione del feedback (urlio). * In questo caso “Feedback” indica il caso in cui una specifica frequenza prodotta dall’amplificatore causa una incontrollabile risonanza della chitarra che crea un suono simile ad un urlo. La funzione AFR del MAGICSTOMP utilizza un filtro che taglia la frequenza causa del feedback per eliminare il feedback stesso.
Scelto un patch la cui funzione AFR è attiva, seguire le istruzioni che seguono per usare la funzione AFR. * L’uso dei pulsanti con la funzione AFR differisce nelle modalità Up/Down e Performance.
GUITAR EFFECTS PROCESSOR Wat is er nieuw en verbeterd aan de MK2 [Deep Edit] Met de zogenaamde “Deep Edit” functie van de MK2 kunt u alle effectparameters voor een patch bewerken, u kunt instellen welke parameters worden geregeld door de drie knoppen op het toestel en al deze instellingen opslaan in het geheugen. Met de oorspronkelijke MAGICSTOMP konden alle bewerkingen en toewijzingen van bedieningsorganen op de computer gebeuren via het “Sound Editor for MAGICSTOMP” programma.
Deep Edit Alle parameters van de geselecteerde patch kunnen worden veranderd. Samen met de mogelijkheid een ander soort effecttype te selecteren kunt u met deze functie uw eigen patches maken. q Druk op de [STORE/EXIT] toets. “PRESS[STORE]1sec” zal verschijnen in de onderste helft van het display.
r Verdraai de knoppen om de bijbehorende parameters in te stellen. Bekijk welke parameters u wilt veranderen en gebruik vervolgens de knoppen onder het display om de ingestelde waarden te veranderen. Als de stand van de knop niet overeenkomt met de waarde voor de bijbehorende parameter, moet u de knop ronddraaien tot de stand wel overeenkomt met de ingestelde waarde voor u deze kunt veranderen (→ Handleiding : bladzijde 144). ÿEDIT-PRM:03/07Ÿ ؇08.
Automatische Feedback Reductie (AFR) functie Uw MAGICSTOMP is uitgerust met een zeer verfijnde Automatische Feedback Reductie functie (AFR) om storende feedback (rondzingen) tegen te gaan. * Onder “feedback” verstaan we in dit geval de situatie waarin een bepaalde door de versterker geproduceerde frequentie oncontroleerbare resonanties veroorzaakt in de gitaar, waardoor het geluid gaat ‘rondzingen’.
Nadat u een patch heeft geselecteerd waarvoor de AFR functie in werking is, kunt u de onderstaande instructies volgen voor het gebruiken van de AFR functie. * De werking van de AFR functieschakelaar is in de Up/Down selectiefunctie anders dan in de Uitvoeringsfunctie. q Bij feedback in de Up/Down selectiefunctie dient u op ON/OFF te drukken, terwijl u in de Uitvoeringsfunctie de toets die correspondeert met de op dit moment geselecteerde patch (–, ON/OFF, +) in dient te drukken.
GUITAR EFFECTS PROCESSOR MK2的新功能和改进 [精细编辑] MK2的精细编辑功能可以让您对组成插曲的所有效果参数进行编辑,设置由本机的3个控制旋钮所控制 的参数,并且把这些设置存入存储器中。对原来的MAGICSTOMP而言,全部的编辑和控制旋钮参数指 定在运行“Sound Editor for MAGICSTOMP”的电脑执行,而对MAGICSTOMP MK2而言,所有这些操作 都可以由MAGICSTOMP MK2完成。 → 更多信息,参阅本手册的第32页。 [PHONES插口] PHONES插口(立体声微型插口)能够让您通过头戴式耳机在监听MAGICSTOMP的声音输出时练习或编 辑插曲。(输出电平/阻抗: –10dBm/150Ω) * 使用音量旋钮调节音量。 * 将一付头戴式耳机连接到PHONES插口时,仍然通过OUTPUT插口输出。 PHONES插口 使用一付头戴式耳机监听时,请务必适当地调节音量,以免损坏您的听 力。 [自动反馈抑制功能] 可以在“AcousticMulti”效果下使用自动反馈抑制功能,实时抵消反馈带来的振鸣。 → 更多信息,请参看本手册第34页。
精细编辑 可以对当前所选插曲的任何参数加以编辑。您可以使用精细编辑,同时选择一个不同的效果,来创建原创 插曲。 q 按[STORE/EXIT](存储/退出)钮。 “PRESS[STORE]1sec”将显示在显示屏的下半部。 * 如果选择了一首预置插曲时按[STORE/EXIT](存储/退出)钮,那么相应的用户插曲号码就被自动选择为 要存储的指定插曲号。 U01:DIST1 PRESS[STORE]1sec w 按一次ON/OFF开关,然后迅速释放(在1秒内)。 您现在处于精细编辑模式,显示屏将如下显示。 * 如果您按ON/OFF开关超过1秒,则将进入曲名编辑模式。(→用户手册∶参看174页) 0EDIT-KNOB0TYPE ‡KNB1fiKNB2áKNB3 EDIT-PRM:02/07 ‡MID0fiTRE0áPRE0 或 精细编辑图标 精细编辑图标 e 使用+/- 开关选择参数设置显示 当前选择的插曲参数列在数页上。使用“+”或“–”开关在显示屏上查看下一页或上一页。 * 每一参数的更多信息,请参考单独的效果清单。 显示的参数设置显示页 是全部7页中的第3页 该图标表示还有上一页 使用“–”开
r 转动旋钮编辑相应的参数 查看了想要编辑的参数后,可以使用位于显示屏下方的旋钮对参数进行编辑。如果旋钮的位置和参 数值不匹配,则在改变参数设置之前,必须转动旋钮,直至它和相应的参数值位置相匹配。(→用 户手册∶170页) EDIT-PRM:03/07 ‡08.
自动反馈抑制(AFR)功能 MAGICSTOMP配有非常先进的自动反馈抑制功能(AFR),用以消除反馈(振鸣)。 * 在这里,“反馈”是指当放大器产生一个特定频率的信号时,引起吉他产生不可控制的谐振,从而产生振鸣 的现象。 MAGICSTOMP的AFR功能采用一种陷波滤波器,该滤波器用来滤掉产生反馈的频率,从而消除反馈。最多 可以设置同时运行5个陷波滤波器。 只有将插曲的效果设为“AcousitcMulti”时,才能使用AFR功能。 注意 请注意:经常性的高音量反馈会对设备造成损坏。 ■ 打开AFR功能 从工厂出货时,MAGICSTOMP MK2的AFR功能设为OFF(该功能未激活),请按下述步骤打开AFR功能(激 活该功能)。 q 按[STORE/EXIT](存储/退出)钮后,再按两次ON/OFF开关在精细编辑模式下选择“Effect Type Select”屏幕显示。 * 按两次该开关时,务必每次都在1秒内释放该开关。 EDIT-FXT:63/63 AcousticMulti EDIT-FXT:63/63 AFR0FUNCTION0ON w 按住ON/OFF开关(约4秒钟),直到如 下显示。
在AFR功能激活时选择一首插曲后,请按下文的说明使用AFR功能。 * AFR功能开关的操作因增/减模式和演奏模式而异。 q 在增/减模式下显示反馈时,按ON/OFF开关,或者在演奏模式下按与当前选择插曲相应的开 关(–,ON/OFF,+)时: * 上述步骤(–,ON/OFF,+)开关不能使用于转变AFR功能处于激活状态中的插曲的ON/OFF效果的开关。 MAGICSTOMP将自动识别引起反馈的频率,同时激活一个空闲的陷波滤波器。当滤波器识别出有问题 的频率后,显示屏将显示类似下图所示的内容,然后返回到原来的状态。 为了表示AFR功能处于激活状态,当处于增/减模式时,ON/OFF开关的灯闪烁,当处于演奏模式时, 当前所选插曲相应开关的灯(–,ON/OFF,+)闪烁。 U96 Natural AFR10F=00221Hz * 如果没有设置陷波滤波器,在返回原来的状态前,显示屏将会显 示如下内容。 U96 Natural 00CAN'T0DETECT w 如果使用一个带通滤波器不能有效地处理反馈问题,请按步骤 q 所述按下开关并设置第 二个滤波器。最多可以设置5个带通滤波器。 * 如果5个滤波器都已设置完
WE43060 Printed in China