Owner's Manual

ManualsBrandsYamaha ManualsOtherME02R

ME02R96

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

ME02R96

Owner’s Manual

Thank you for your purchase of the YAMAHA ME02R96 memory expansion kit for the 02R96 mixer.

By replacing the original CPU board with this ME02R96 expansion board, you will expand your

mixer’s automix memory to 7MB—a sevenfold increase that will make your mixer even more versa-

tile and even easier to use.

Please read through the following precautions carefully before having the serviceperson install this

ME02R96 expansion kit. Be sure to retain the manual in a safe place.

Precautions

WARNINGS

Failure to observe the following warnings may lead to fatality or serious injury from ﬁre or

electric shock.

CAUTIONS

Failure to observe the following cautions may lead to injury, or may result in damage to

equipment or other property.

●

Do not attempt to disassemble or modify the

ME02R96 board. Do not apply excessive force to

board connectors or other board components.

(Mishandling of the board may lead to shock, ﬁre

hazard, or equipment failure.)

●

Be sure to unplug the 02R96 main unit from the

power supply before installing the ME02R96

board (to eliminate shock hazard).

●

Be careful to avoid catching or snagging ﬁngers

while carrying out the installation.

●

Before starting installation, be sure to save all

important data from the 02R96 unit to an external

MIDI device. This installation process will clear all

of the unit’s user memory and will reset all set-

tings to their defaults.

●

When handling the ME02R96 board, do not

touch the board’s metallic leads (pins). (Pins are

sharp and may cause hand cuts.)

●

The ME02R96 board is electrostatic-sensitive.

Before handling the board, you should brieﬂy

touch the main unit’s metal casing with your bare

hand so as to drain off any static charge from

your body.

●

Be sure to install the included lithium battery. This

is a backup battery that is required maintain the

data in the 02R96’s expanded memory.

The ME02R96 expansion kit must be installed by an authorized

serviceperson. Please contact a local Yamaha dealer or a service

center to arrange for installation. Do not attempt to install the

ME02R96 on your own.

Summary of content (9 pages)

PAGE 1
DEUTSCH Thank you for your purchase of the YAMAHA ME02R96 memory expansion kit for the 02R96 mixer. By replacing the original CPU board with this ME02R96 expansion board, you will expand your mixer’s automix memory to 7MB—a sevenfold increase that will make your mixer even more versatile and even easier to use. ENGLISH ME02R96 Owner’s Manual The ME02R96 expansion kit must be installed by an authorized serviceperson. Please contact a local Yamaha dealer or a service center to arrange for installation.
PAGE 2
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PAGE 3
ENGLISH Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. * Please dispose of used batteries in accordance with local regulations. * Illustrations in this manual are for explanatory purposes only, and may not match the actual appearance of the product. * Company names and product names used herein are trademarks or registered trademarks of their respective owners.
PAGE 4
System software: The ME02R96 includes system version 1.20 or higher, and is not compatible with pre-V1.20 software. Before upgrading your 02R96 again in the future, be sure that your updater program is V1.20 or higher. Studio Manager: The ME02R96 is not compatible with Studio Manager versions prior to V1.1.1. If your version is older than V1.1.1, please replace it by installing the Studio Manager version included on the accompanying CD-ROM.
PAGE 5
● Install the ME02R96 Expansion Kit ENGLISH ~The following instructions are intended for use by authorized servicepersons only.~ This kit is not user-installable. Users should contact a local Yamaha dealer or a service center to arrange for installation by a Yamaha-authorized serviceperson. Detach and Raise the Control Panel When removing each screw, note its location and be sure to return it to the same place when reassembling. Screws come in various sizes and are not interchangeable. 1. 2.
PAGE 6
If the MB02R96 peak meter bridge is installed on the 02R96, remove it. First disconnect the bridge cable from the METER connector on the 02R96. Then remove the 4 screws holding the bridge in place (as shown below), and remove the bridge. 2 Screws 02R96 METER Connector 2 Screws ME02R96 5 ENGLISH 3.
PAGE 7
ENGLISH 4. Remove the screws indicated in the illustration below: 7 screws from the left side, 7 screws from the right side, 7 screws from the front, and 7 screws (or 5 screws, if 2 were already removed at Step 3) from the rear. Positioning Screw 7 Screws Positioning Screw Positioning Screw LCD 7 Screws 7 Screws Positioning Screw 7 Screws 5. Hold onto the LCD, and lift up the rear of the control panel. LCD 6.
PAGE 8
CPU ENGLISH 4 Screws Lithium Battery Install the ME02R96 Expansion Board and the Battery 1. Disconnect the 2 flat cables from the connectors on the CPU board. The cables are connected to white connectors. Before disconnecting each cable, pull the connector latch up as shown in the illustration. 2. 3. Flat Cable Latch Remove the 4 screws holding the CPU board in place, and remove the CPU board. Mount the ME02R96 board.
PAGE 9
ENGLISH Reattach the Control Panel 1. Lower the control panel back into place. Then refasten with the original screws, in the following order: front panel first, then the sides, and then the rear. When fastening each panel, always fasten the positioning screw first (see illustrations on page 6 above). Before screwing in the control panel, check to make sure that you have not left any loose screws or tools inside the 02R96 casing. Loose objects left in the casing may cause damage to the equipment. 2.