SECCIÓN DE MENSAJES ESPECIALES Este producto utiliza una fuente de alimentación externa (adaptador) o pilas. NO conecte este producto a ninguna fuente de alimenta
L¢ agradecemos la adquisición del Pedal Controlador MIDO MFC10. EIMFC10 es un pedal controlador MIDO de gran versatilidad, capaz de transmitir cambios de programa y cambios de control a procesadores de efectos, generadores de tonos, teclados, guitarras MIDO, cajas de ritmos, etc. Ademas del pedal controlador interno, se pueden conectar al MFC10 hasta 4 pedales controladores o conmutadores opcionales externos para aumentar la versatilidad de control.
= Emplazamiento Para evitar su deformación, decoloración o dacios més graves, no exponga el MFCI0 a las siguientes condiciones: & Luz solar directa (por ejemplo, cerca de una ventana). ® Altas temperaturas (por ejemplo, cerca de una fuente de calor}. ® Humedad excesiva. * Exceso de polvo. » Vibraciones fuertes. W UTILICE LA ALIMENTACIÓN ADECUADA ® Alimentación de] MRC10 debe provenir solé del adapta dor de ¢.a. Piyama (el PAPABLE u taro adaptador particular miente recomendado por Piyama.
Utilice el adaptador de corriente PAPABLE (u foro adaptador recomendado por Piyama) para suministrar alimentación al MFG10 de una toma de pared adecuada. [ e 1 Conecte ef enchufe de) adaptador « ki toma [DC IN] del panel posterior, Asegure el cable en el sujeta cables para evitar la descongestione accidental durante su uso. Adaptador de corriente 2 Conecte el adaptador de C.A. en cualquier toma de pared.
Panel frontal PIYAMA »%fln;m [888] MMU (O] (10 ] Panel posterior PIYAMA como Panel frontal @ Indicadores de parámetros (véanse paginas modo de edición. parpadear el indicador del parámetro seleccionado en cada morenito.
@ Pedal interruptor (véanse paginas 9, 12) Selecciona mineros de memoria, @ Pedal interruptor [x10] (véanse paginas 9, 12) Selecciona la cifra de las centenas o decenas. ® Pedal controlador interno (véase la pagina 22) El pedal controlador puede utilizarse para transmitir cambios de control, presión posterior a Ta pulsación, inflexión de tono, etc. a dispositivos MIDO externos.
Memoria de cambio de programa TACHONO cativar la memoria de cambio de Si estad iluminado el indicador programa, La mamaria de cambio de programa transmite los mineros de canal MIDE-16 y los datos de cambio de programa (001-128) que estén guardados en la memoria, Existen 128 posiciones de memoria en las que pueden guardarse los datos de cambio de programa. Ademas, los datos de selección de banco (00=MSB, pueden ser transmitidos justo con los datos de cambio de programa. .
Para cambiar y seleccionar todas fas cifras Pulse [x10] dos veces. Si ta cifra de Jas centenas es 1, combinatoria O, y síes O cambiar a 1 (la cifra de fas decenas parpadear, indicando la espera pura la introductorio de datos).
Memoria de funciones Pulse [FUNCIONARIO. Su indicador se iluminad, v quedar activada s memoria de funciones. La memoria de funciones guarda y transmite datos MIDO existentes en su memoria, tales como activacion/desactivacion de M Control de Ia memoria de funciones (transmisión) Los datos de función se transmiten cuando se selecciona un minero de memoria con los pedales conmutadores 1x10]. Para el almacenamiento de estos datos existen 100 posiciones de memoria (FO O-PIY).
~— Modo Normal A o SRR Lista de cambio de control (para dispositivas compatibles con Control de portante N| S8 i Uso extensivo de Efecto | (verbigracia banco N extensivo de Bisector 3 (arruchar) NIS (n S Jso extensivo de Efecto 4 (celeste) N S Tiempo de portento N Aumento de dato NIS Introducción de datos N Disminución Je datos NS Volumen principal S ARPÓN (LSB) N | S Mando de racionalizan S N|S Expresión Selección de banco N RPN (MSB) 51§ Introductorio de datos S idos low sonidos desactivados NI § Mantenim
= Sodomizo modo MIX se pueda acceder al mismo tiempo a los dalos de cambio de programa v a los datos de función sin tener que cambiar de dome con el interruptor FUNCIONARIO.
= Modo = B Control de la memoria del modo MIX {transmisión} En el modo MIX, se pueden almacenar un monorrimo de 25 memorias de cambio de programa (independiente en este modo) y S memorias e funciones para sy posterior tridimensional por MIL sutilice los pedales conmutadores ded nivel superior para transmitir los datos de función. P VEE ~ Fp] Con los pedales se transmiten fos datos de función.
M Edición del modo MIX Desde el dome MIX del MFC10, pulse el boten [MEMORA EDITA] * Edición de la memoria de cambio de programa Los datos de Jos 25 tipos de memoria (independiente en este modo de los pedales conmutadores se pueden editar siguiendo el mismo procedimiento que para editar ka memoria de cambio de programa en el modo Normal {véase la púgil nat 10}, ¢ Edición de la memoria de funciones Los datos de los § tipos de memoria de Tos depiles conmutadores se pueden editar siguiendo el mismo procedí mien
Mensajes de error Si se produce un error mientras se utiliza el MFC10, en la pantalla aparecerá uno de los siguientes mensa&8 jes. Pulse el botón [WRITE/EXIT] para regresar al moda de reproducción normal del MFC10. {En el caso & det me mensaje de error 5, puede que Ja mamaria interna tenga algún problema; pulsando [WRITE/EXIT], la [ moría interna se alcalinizar automáticamente. Erl Error de recepción MIDO. Se ha producido un error durante |a recepcionista de datos.