MMP1 to TMC-1 Setup Guide Version 1.
Contents Introduction ................................................................................................................. 3 Equipment used .......................................................................................................... 3 Part Names and Functions- ........................................................................................ 4 Connection .................................................................................................................
Introduction The TMC-1 is a monitor controller developed by CB Electronics. It allows remote control of the Yamaha MMP1 Studio Monitor Management System via Ethernet connection, allowing for level adjustments, mute on/off, and monitor source selection. This guide explains how to connect the MMP1 to the TMC-1 and set up the system. For more information about TMC-1 functions that can be used as to control the MMP1, see “TMC-1 - MMP1 Monitor remote” on CB Electronics’ website.
Part Names and Functions- ① ② ③ ④ ⑦ ⑤ ⑧ ⑥ ⑨ ⑩ ① Display Shows the name of the currently displayed page in the top left corner and the function names assigned to each User Key at the bottom. ② User Keys Functions can be assigned to eight User Keys using the TMC-1 setup software. See "To assign a function to the User Keys" on page 11 for how to assign a function to the User Keys.
③ [Function] keys The following functions are assigned by default. [Fn-1] Speaker Select (Pressing this button allows the [User] keys to select speakers.) [Fn-2] A/B Select (Selects either In/Out selections of A or B.) [Fn-3] Solo Defeat (Deactivates both Stem Solo and Speaker Solo.) ④ [User] key The SLS function is assigned by default. Since the MMP1 does not support the SLS function, assign another function to this key. ⑤ [Page] key (U.
⑨ [Ctrl] key (Spk. Solo) Pressing this key allows the User Keys to select “Speaker Solo”. Each press of this key switches the speaker solo bank between 00 and 01. A different function can be assigned to this key using theTMC-1 setup software. ⑩ Monitor Level encoder Rotating this encoder adjusts the monitoring level. Pressing the encoder mutes or unmutes the monitor outputs. This function syncs with the [Mute] key. * The texts in parentheses are the ones shown in the display.
Connection This chapter explains how to connect the MMP1, TMC-1, and a computer. [An example of the system configuration] MMP1 Ethernet cable USB cable Network Switch (SWP1) Computer TMC-1 TMC-1 Connect the MMP1, TMC-1, and a computer to a network switch using Ethernet cables. Use a CAT5e or higher Ethernet cable for the connection. Connect the TMC-1 to the computer via the USB ports. This connection is required only for setting up the TMC-1.
Setting up the system To set the TMC-1 operation mode 1. Press the [Page] and [Select] keys simultaneously to display the Select Page. 2. Press User Key 8 "Setup" to display the Setup Menu. 3. While holding down the [Select] key, press User key 4 "→" to display the Adv Menu 24 - MMP1 Device Emulation page. 4. Use the User Keys 3 "↑" and 7 "↓" to select the "MMP1 Compliant" mode.
3. Use User Keys 3 "↑" and 7 "↓" to select the IP address for the MMP1 and press Key 2 "Select". This will connect the TMC-1 to the MMP1. You can check the TMC-1 IP address on the Network TCP/IP page by pressing User Key 4 "→". If the TMC-1 has an IP address with a different subnet from the MMP1, pressing User Key 2 “Select” on the Discovery page will set a network address that has the same subnet as the MMP1. 4. Press the [Page] key to display the Meters page.
TMC-1 IP address The TMC-1 IP address can be set using the TMC-1 setup software. For details, see "To set TMC-1 IP address" on page 12. After assigning the IP address, check the IP address on the Discovery page. Precautions for a system with a Dante network Since the TMC-1 has a Fast Ethernet port, turn on the IGMP snooping and querier settings of the network switch in a system that runs together with a Dante network. See the user guide of the network switch for details.
When the software is connected to the TMC-1, the Midi Port column will change from "Midi Not Open" in a red bar to "Midi OK" in a green bar. To assign a function to the User Keys You can change the functions assigned to the User Keys in the [User Key] tab. Select a function to be assigned to each User Key from the pull-down menus. The TMC-1 has two banks for the User Keys and you can switch the bank between 1 and 2 in the [User Key] tab.
To set TMC-1 IP address You can set a TMC-1 IP address in the [Set IP] tab. Input an IP address and subnet mask to the "IP Address" and "IP Mask" columns respectively, and click the [Set] button. This will set the IP address for the TMC-1. If you click the [Read] button, the current IP address will be shown. To update TMC-1 Firmware and factory reset You can update the TMC-1 firmware and reset it to the default settings using MidiUpd software. For details about MidiUpd, see the MidiUpd guide. https://www.
User Key List (Version 19612) User Key Description functions Sum Spk Solo Turns on or off "SUM" (Monitor Source Summing). Turns on or off SOLO for a specified main monitor. (If used with the MUTE function, the MUTE function will be prioritized.) Spk Mute Mutes or unmutes a specified main monitor. A/B Sel Switches the monitor level between A and B. Main Selects Speaker Set A. Alt Selects Speaker Set B. Mini Selects Speaker Set C. Main ip Selects Monitor Source 1.