Owner`s manual

Voice mode
Performance
mode
Song mode Utility mode File mode Master mode
Pattern mode
Mixing Voice
mode
Reference
Performance Edit mode Common Edit
172
Owner’s Manual
Voice Edit parameters are divided into Common Edit (parameters common to all four Parts), and Part Edit (parameters of individual Parts).
These parameters are for making global (or common) edits to all four Parts of the selected Performance.
Performance Edit mode
[PERFORM] ➞ Performance selection ➞ [EDIT]
Common Edit
[PERFORM] ➞ Performance selection ➞ [EDIT] ➞ [COMMON]
[F1] GENERAL
[SF1] NAME
From this display you can assign the category (sub and main) of the selected Performance, and create a name
for the Performance. The Performance name can contain up to 10 characters. For specific instructions on
naming, see Basic Operation on page 38.
[SF3] MEQ OFS
(Master EQ Offset)
Determines the offset values of the Master EQ in the [F2] OUT/MEF → [SF2] MEQ display. The level of each of
the four bands (with the exception of “MID”) can be adjusted. Moreover, you can also tweak these settings
directly from the four Knobs on the front panel when the [EQ] button is turned on.
[SF4] PORTA (Portamento)
This display allows you to set the Portamento related parameters. The parameters are the same as in the
Performance Play mode. See page 171.
[SF5] OTHER
From this display you can set the control functions for the Knobs and related parameters. With the exception of
Pitch Bend, which cannot be set here, these parameters are the same as in the Voice Edit mode (page 154).
[F2] OUT/MEF (Output/Master Effect)
[SF1] OUT (Output)
Volume Determines the output level of the selected Performance. You can adjust the overall volume, keeping the
balance between all Parts.
Settings: 0 – 127
Pan Determines the stereo pan position of the selected Performance. This parameter offsets the same parameter in
the part edit setting. When the [PAN/SEND] button is turned on, you can also adjust this parameter using the
Knob.
Settings: L63 (far left) – C (center) – R63 (far right)
n A setting of “C” (center) maintains the individual Pan settings of each Part.
RevSend (Reverb send) Determines the Send level of the signal sent from Insertion Effect A/B (or the bypassed signal) to the Reverb
effect. When the [PAN/SEND] button is turned on, you can also adjust this parameter using the Knob.
Settings: 0 – 127
ChoSend (Chorus send) Determines the Send level of the signal sent from Insertion Effect A/B (or the bypassed signal) to the Chorus
effect. When the [PAN/SEND] button is turned on, you can also adjust this parameter using the Knob.
Settings: 0 –127
n For details on the Effect connections in the Performance mode, see page 143.
[SF2] MEQ (Master EQ)
From this display you can apply five-band equalization to all Parts of the selected Performance. You can raise
or lower the signal level at the Frequency of each band (LOW, LOWMID, MID, HIGHMID, HIGH).
SHAPE Determines whether the equalizer type used is Shelving or Peaking. The Peaking type attenuates/boosts the
signal at the specified Frequency setting, whereas the Shelving type attenuates/boosts the signal at
frequencies above or below the specified Frequency setting. This parameter is available only for the LOW and
HIGH frequency bands.
Settings: shelv (Shelving type), peak (Peaking type)
FREQ (Frequency) Determines the center frequency. Frequencies around this point are attenuated/boosted by the Gain setting.
Settings: LOW: Shelving 32Hz – 2.0kHz, Peaking 63Hz – 2.0kHz
LOWMID, MID, HIGHMID: 100Hz – 10.0kHz
HIGH: 500Hz – 16.0kHz
GAIN Determines the level gain for the Frequency (set above), or the amount the selected frequency band is
attenuated or boosted.
Settings: -12dB – 0dB – +12dB
Q (Frequency Characteristic) This varies the signal level at the Frequency setting to create various frequency curve characteristics.
Settings: 0.1 – 12.0
n For details on the EQ, see page 141.
[SF3] MEF (Master Effect)
From this display you can set the Master Effect related parameters.
Switch Determines whether Master Effect is applied or not to the selected Performance.
Settings: off, on
Type Determines the Master Effect type.
Settings: Refer to the Effect Types list in the separate Data List booklet.
n The available parameters except for the above two differ depending on the currently selected effect type. Refer to the separate Data List booklet for details.