Owner`s manual

Appendix
221
Owner’s Manual
Display Messages
Display Messages
LCD Indication Explanation
Are you sure ? [YES]/[NO] Confirms whether you want to execute a specified operation or not. Press [INC/YES] or [DEC/NO] as required.
Arp memory full The internal memory for Arpeggio data is full, preventing storing the recorded sequence data as an Arpeggio.
Arpeggio type stored The current Arpeggio type has been stored to one of the [SF1] - [SF5] buttons.
Bad USB device The USB storage device is unusable. Format the USB storage device and try again.
Bulk protected. Bulk data was received when RcvBulk was set to “protect.” (See page 209.)
Can’t make folder. No more directories can be created below the current level.
Can’t undo OK? [YES]/[NO]
When certain Song/Pattern Jobs are executed, internal memory becomes too full for use of the Undo operation.
Press [INC/YES] if this is OK, or [DEC/NO] to abort the operation. Try again after erasing unwanted Songs, Patterns,
or User phrases.
Choose user phrase.
You have attempted to record a Pattern track to which a preset phrase is assigned. If you wish to use a preset
phrase as raw material for Pattern recording, copy it to a User phrase before recording.
Completed. The specified load, save, format, or other Job has been completed.
Device number is off. Bulk data cannot be transmitted/received since the device number is off.
Device number mismatch. Bulk data cannot be transmitted/received since the device numbers don’t match.
Executing... A format operation or Job is being executed. Please wait.
File already exists. A file having the same name as the one you are about to save already exists.
File not found. The file of the specified type cannot be found on the USB storage device
Folder is too deep. Directories below this level cannot be accessed.
Folder not empty. You have attempted to delete a folder that contains data.
Illegal check box.
No check boxes have been checked in a Sequencer track Job which requires a check box selection. Check the
appropriate check box.
Illegal file The file specified for loading is unusable by the MO or cannot be loaded in the current mode.
Illegal file name. The specified file name is invalid. Try entering a different name.
Illegal input. An invalid input or value has been specified. Check the input method or value.
Illegal measure. An invalid measure number has been specified in the Song/Pattern mode. Select the measure again.
Illegal phrase number. An invalid phrase number has been specified in the Pattern mode. Select the phrase again.
Illegal track number. An invalid track number has been specified in the Song/Pattern mode. Select the track again.
Incompatible USB device A USB device which cannot be used with the MO has been connected to the USB TO DEVICE connector.
Meter mismatch
In the Pattern Job mode, the meter (time signature) of the destination Pattern is different from the meter of the source
Pattern.
MIDI buffer full. Failed to process the MIDI data because too much data was received at one time.
MIDI checksum error. An error occurred when receiving bulk data.
MIDI data error. An error occurred when receiving MIDI data.
Mixing stored In the Song/Pattern mode, the Mixing settings have been loaded from the file.
Mixing Voice full
The Mixing Voice cannot be stored because the number of Voices already stored has exceeded the maximum
capacity.
No data.
When a Song/Pattern Job is executed, the selected track or range contains no data. Select an appropriate track or
range. In addition, this message appears when a Job related to a Mixing Voice cannot be executed because the
specified Mixing Voice is not available.
No F7 (End of Exc.)
Exclusive data has been entered or changed without the necessary “End of Exclusive” byte (F7). Make sure F7 is
included.
No response from USB device There is no response from the USB device connected to the USB TO DEVICE terminal.
Not empty folder You have attempted to delete a folder that contains data.
Now loading... (xxxx) Indicates that a file is being loaded.
Now saving... (xxxx) Indicates that a file is being saved.
Now scanning auto loaded files Scanning for the files specified for Auto Load.
Now working... Canceling the Load/Save operation by pressing the [EXIT] button.
Overwrite? [YES]/[NO]
A save operation will overwrite data on the USB storage device, and this message confirms whether it is OK to
continue or not. Press [INC/YES] or [DEC/NO] as required.
Pattern length mismatch. A Pattern Job will result in the length of a Pattern being greater than 256 measures.
Phrase length mismatch A Pattern Job will result in the length of a phrase being greater than 256 measures.
Phrase number overflow The maximum number of phrases (256) has been exceeded when recording, executing a Pattern Job, or editing.
Please keep power on.
The data is being written to Flash ROM.
Never attempt to turn off the power while data is being written to Flash ROM. Turning the power off while this
message is shown results in loss of all user data and may cause the system to freeze (due to corruption of data in
the Flash ROM). This may also result in the MO being unable to properly start up the next time the power is turned
on.