User Manual

ManualsBrandsYamaha ManualsMusical InstrumentsMO6

Data List

MIDI Data Format

Many MIDI messages listed in the MIDI Data Format section are expressed in hexadecimal

or binary numbers. Hexadecimal numbers may include the letter “H” as a suffix. The letter

“n” indicates a certain whole number.

The chart below lists the corresponding decimal number for each hexadecimal number.

Additional Notes

• For example, 144 – 159(Decimal)/9nH/1001 0000 – 1001 1111(Binary) indicate the note-

on messages for the channels 1 through 16 respectively. 176 – 191/BnH/1011 0000 –

1011 1111 indicate the control change messages for the channels 1 through 16

respectively. 192 – 207/CnH/1100 0000 – 1100 1111 indicate the program change

messages for the channels 1 through 16 respectively. 240/F0H/1111 0000 is positioned

at the beginning of data to indicate a system exclusive message. 247/F7H/1111 0111 is

positioned at the end of the system exclusive message.

• aaH (Hexadecimal)/0aaaaaaa (Binary) indicates the data addresses. The data address

consists of High, Mid and Low.

• bbH/0bbbbbbb indicates byte counts.

• ccH/0ccccccc indicates check sums.

• ddH/0ddddddd indicates data/value.

SYNTHESIZER/SEQUENCER PART

(1) TRANSMIT FLOW

MIDI <-+-[SW1]--+---------NOTE ON/OFF 9nH

OUT | |

| +---------KEY'S AFTER TOUCH AnH (Seq only)

| |

| +---------CONTROL CHANGE (All in Seq)

| | MODULATION BnH,01H

| | VOLUME BnH,07H

| | PAN BnH,0AH

| | SUSTAIN SWITCH BnH,40H

| | FILTER RESONANCE BnH,47H

| | EG RELEASE TIME BnH,48H

| | EG ATTACK TIME BnH,49H

| | FILTER CUTOFF FREQ BnH,4AH

| | EG DECAY TIME BnH,4BH

| | REVERB SEND BnH,5BH

| | CHORUS SEND BnH,5DH

| | ASSIGNABLE CONTROLLERS BnH,(00H..5FH)

| |

| +--[SW7]--BANK SEL MSB BnH,00H

| | BANK SEL LSB BnH,20H

| |

| +---------CHANNEL MODE MESSAGE (Seq only)

| | RESET ALL CONTROLLERS BnH,79H

| | LOCAL CONTROL BnH,7AH

| | OMNI MODE OFF BnH,7CH

| | OMNI MODE ON BnH,7DH

| | MONO MODE ON BnH,7EH

| | POLY MODE ON BnH,7FH

| |

| +--[SW8]--PROGRAM CHANGE CnH

| |

| +---------CHANNEL AFTER TOUCH DnH

| |

| +---------PITCH BEND CHANGE EnH

+--[SW4]------------SYSTEM COMMON MESSAGE

| SONG POSITION POINTER F2H

| SONG SELECT F3H

+--[SW4]-----------SYSTEM REALTIME MESSAGE

| TIMING CLOCK F8H

| START FAH

| CONTINUE FBH

| STOP FCH

+-------------------ACTIVE SENSING FEH

+--[SW5]-+----------SYSTEM EXCLUSIVE MESSAGE (All in Seq)

| +--[SW6]-- <BULK DUMP>

| | F0H 43H 0nH 7FH 00H bhH blH ahH amH alH ddH...ddH ccH F7H

| |

| +--[SW6]-- <PARAMETER CHANGE>

| F0H 43H 1nH 7FH 00H ahH amH alH ddH...ddH F7H

+-------------------SYSTEM EXCLUSIVE MESSAGE

| IDENTITY REPLY

| F0H 7EH 7FH 06H 02H 43H 00H 41H 33H (or 34H) 06H 00H 00H 00H

| 7FH F7H

+--[SW3,4]----------MIDI MACHINE CONTROL

STOP F0H 7FH 7FH 06H 01H F7H

DEFERRED PLAY F0H 7FH 7FH 06H 03H F7H

LOCATE F0H 7FH 7FH 06H 44H 06H 01H hrH

mnH scH frH ffH F7H

[SW1] MIDI Transmit Channel

In the Master mode: complies with Zone Transmit Channel.

In the mode other than the Master: complies with Keyboard Transmit Channel.

The sequence data played back in the Song/Pattern mode is transmitted according to the MIDI Filter settings.

[SW2] MIDI Control Mode

[SW3] MIDI Sync (transmitted when the MIDI Sync is set to MTC.)

[SW4] Seq MIDI Control

[SW5] MIDI Device Number

When set to all, transmitted via 1.

The sequence data played back in the Song/Pattern mode is transmitted according to the MIDI Filter settings.

[SW6] The System data can be transmitted/recognized in any mode.

Regarding the other types of data, it depends on the current mode whether they can be transmitted/recognized

or not.

[SW7] SYSTEM Bank Select Switch

[SW8] SYSTEM Program Change Switch

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

Decimal Hexadecimal Decimal Hexadecimal