User Manual

MONTAGE Data List
147
Effect Parameter List
Variation, Insertion Block
[0] THRU/OFF
When this type is selected, no parameters are available.
Category — REVERB
[1] SPX HALL
[2] SPX ROOM
[3] SPX STAGE
[4] GATED REVERB
[5] REVERSE REVERB
Category — DELAY
[1] CROSS DELAY
[2] TEMPO CROSS DELAY
[3] TEMPO DELAY MONO
[4] TEMPO DELAY STEREO
[5] CONTROL DELAY
[6] DELAY L, R
No. Parameter Range Value Tbl No.
1 Reverb Time 0.3s – 30.0s (0 – 69) 4
2 Diffusion 0 – 10 (0 – 10)
3 Initial Delay 0.1ms – 99.3ms (0 – 63) 5
4 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
5 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Reverb Delay 0.1ms – 99.3ms (0 – 63) 5
12 Density 0 – 4 (0 – 4)
13 ER/Rev Balance E63>R – E=R – E<R63 (1 – 127)
14 Feedback High Damp 0.1 – 1.0 (1 – 10)
15 Feedback Level -63 – +63 (1 – 127)
16 —
No. Parameter Range Value Tbl No.
1 Type Type A, Type B (0 – 1)
2 Room Size 0.1 – 20.0
0.1 – 7.0 (Ins17)
(0 – 127)
(0 – 44)
6
3 Diffusion 0 – 10 (0 – 10)
4 Initial Delay 0.1ms – 200ms
0.1ms – 99.3ms (Ins17)
(0 – 127)
(0 – 63)
5
5 Feedback Level -63 – 0 – +63 (1 – 127)
6 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
7 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
8—
9—
10 Dry/Wet D63>W – D=W – D<W63 (1 – 127)
11 Liveness 0 – 10 (0 – 10)
12 Density 0 – 3 (0 – 3)
13 Feedback High Damp 0.1 – 1.0 (1 – 10)
14 —
15 —
16 —
No. Parameter Range Value Tbl No.
1 Delay Time L>R 0.1ms – 1638.3ms (1 – 16383)
2 Delay Time R>L 0.1ms – 1638.3ms (1 – 16383)
3 Feedback Level -63 – +63 (1 – 127)
4 Input Select L, R, L&R, L-MODE2, R-MODE2 (0 – 4)
5 Feedback High Damp 0.1 – 1.0 (1 – 10)
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13
EQ Low Frequency 32Hz – 2.0kHz (4 – 40) 3
14
EQ Low Gain -12dB – +12dB (52 – 76)
15 EQ High Frequency 500Hz – 16.0kHz (28 – 58) 3
16
EQ High Gain -12dB – +12dB (52 – 76)
No. Parameter Range Value Tbl No.
1 Delay Time L>R 32nd/3 – 4thx6 (0 – 19) 13
2 Delay Time R>L 32nd/3 – 4thx6 (0 – 19) 13
3 Feedback Level -63 – +63 (1 – 127)
4 Input Select L, R, L&R, L-MODE2, R-MODE2 (0 – 4)
5 Feedback High Dump 0.1 – 1.0 (1 – 10)
6 Lag -63ms – +63ms (1 – 127)
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY above.
No. Parameter Range Value Tbl No.
1 Delay Time 32nd/3 – 4thx6 (0 – 19) 13
2 Feedback Level -63 – +63 (1 – 127)
3 Feedback High Damp 0.1 – 1.0 (1 – 10)
4 L/R Diffusion -63ms – +63ms (1 – 127)
5 Lag -63ms – +63ms (1 – 127)
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY above.
No. Parameter Range Value Tbl No.
1 Delay Time 32nd/3 – 4thx6 (0 – 19) 13
2 Feedback Level -63 – +63 (1 – 127)
3 Feedback High Dump 0.1 – 1.0 (1 – 10)
4 L/R Diffusion -63ms – +63ms (1 – 127)
5 Lag -63ms – +63ms (1 – 127)
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 147.
No. Parameter Range Value Tbl No.
1 Delay Time 0.1ms – 1486.0ms (1 – 14860)
2 Delay transition rate 1 – 48 (1 – 48)
3 Feedback Level -63 – +63 (1 – 127)
4 Feedback High Damp 0.1 – 1.0 (1 – 10)
5—
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 147.
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Control Type Normal, Scratch (0 – 1)
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Tbl No.
1 Delay Time L 0.1ms – 1638.3ms (1 – 16383)
2 Delay Time R 0.1ms – 1638.3ms (1 – 16383)
3 Feedback Time 1 0.1ms – 1638.3ms (1 – 16383)
4 Feedback Time 2 0.1ms – 1638.3ms (1 – 16383)
5 Feedback Level -63 – +63 (1 – 127)
6 Feedback High Damp 0.1 – 1.0 (1 – 10)
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 147.
No. Parameter Range Value Tbl No.