Data List

MONTAGE Data List
155
Effect Parameter List
[5] SPIRALIZER P
[7] SPIRALIZER F
[6] TEMPO SPIRALIZER P
[8] TEMPO SPIRALIZER F
[9] ISOLATOR
[10] SLICE
[11] TECH MODULATION
[12] CONTROL FILTER
[13] VINYL BREAK
No. Parameter Range Value Tbl No.
1 Spiral Speed -39.7Hz – 0.00Hz – +39.7Hz (1 – 255) 60
2 Filter Offset C-2 – G8 (0 – 127)
3 Feedback 0 – 127 (0 – 127)
4 Spiral Step Mode Continuous, Semitone, Scale (0 – 2)
5 Spiral Step Semitones 1 semitones – 12 semitones (0 – 11)
6 Spiral Step Scale Type Maj, Min (Natural),
Min (Harmonic)
(0 – 2)
7 Spiral Sync Step, Octave (0 – 1)
8 Offset Transition Rate 1 – 62 (1 – 62)
9 Spiral Step Transition Rate 1/48 – 1/2 (0 – 14) 61
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11
12
13
14
15
16 Spiral Switch Off, On (0 – 1)
No. Parameter Range Value Tbl No.
1 Spiral Speed 32nd/3 – 4thx6 (0 – 19) 13
2 Filter Offset C-2 – G8 (0 – 127)
3 Feedback 0 – 127 (0 – 127)
4 Spiral Step Mode Continuous, Semitone, Scale (0 – 2)
5 Spiral Step Semitones 1 semitones – 12 semitones (0 – 11)
6 Spiral Step Scale Type Maj, Min (Natural),
Min (Harmonic)
(0 – 2)
7 Spiral Sync Step, Octave (0 – 1)
8 Offset Transition Rate 1 – 62 (1 – 62)
9 Spiral Step Transition Rate 1/48 – 1/2 (0 – 14) 61
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11
12
13
14
15 Direction Up, Down (0 – 1)
16 Spiral Switch Off, On (0 – 1)
No. Parameter Range Value Tbl No.
1 On/Off Switch On, Off (0 – 1)
2 Low Level -64 – +63 (0 – 127)
3 Mid Level -64 – +63 (0 – 127)
4 High Level -64 – +63 (0 – 127)
5 Low Mute Off, On (0 – 1)
6 Mid Mute Off, On (0 – 1)
7 High Mute Off, On (0 – 1)
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Tbl No.
1 Divide Type 16th – 4th (5 – 11) 13
2 Gate Time 0 – 100% (0 – 100)
3 Pan AEG Type A – E (0 – 4)
4 Pan AEG Min Level 0 – 127 (0 – 127)
5 Pan Depth -63 –+63 (1 – 127)
6 Divide Min Level 0 – 127 (0 – 127)
7 Pan Type A – J (0 – 9)
8 Drive 0 – 127 (0 – 127)
9 AEG Phase 0 – 15 (x 16th note) (0 – 15)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Phase Reset Off (free run), Key On Reset,
SEQ Start Reset
(0 – 2)
12 Set Slice Tempo — —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 147.
No. Parameter Range Value Tbl No.
1 Mod Speed 0 – 127 (0 – 127)
2 Mod Depth 0 – 127 (0 – 127)
3 Mod Gain -12 – +12dB (52 – 76)
4 Mod Mix Balance D63>W – D=W – D<W63 (1 – 127)
5 Pre Mod HPF Cutoff
Frequency
20Hz – 8.0kHz (0 – 52) 3
6 Mod LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
7 Mod LPF Resonance 1.0 – 12.0 (10 – 120)
8 Delay Time 0.1 – 740.0ms (1 – 7400)
9 Delay Time Offset R 0 – 884 (0 – 884)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Feedback Level -63 – +63 (1 – 127)
12 FB Level Offset R -63 – +63 (1 – 127)
13 Feedback Hi Damp 0.1 – 1.0 (1 – 10)
14 FB Hi Damp Offset R -0.9 – +0.9 (1 – 19)
15 —
16 —
No. Parameter Range Value Tbl No.
1 Filter Type LPF (12dB), LPF (18dB), LPF
(24dB), HPF, BPF
(0 – 4)
2 Cutoff Frequency Control 0 – 127 (0 – 127)
3 Resonance 0 – 127 (0 – 127)
4 Filter Output Level -12dB – +12dB (52 – 76)
5—
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Tbl No.
1 Break Off, On (0 – 1)
2 Speed Fast, Middle, Slow,
Vinyl Stop, Power Off
(0 – 4)
3 Speed Adjust +30% – -30% (0 – 120)
4—
5—
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Output Level -19.5dB – +12dB (1 – 127) 47
12 —
13 —
14 —
15 —
16 —