Data List

MONTAGE Data List
150
Effect Parameter List
Category — TEC
[1] RING MODULATOR
[2] DYNAMIC RING MODULATOR
[3] DYNAMIC FILTER
[4] AUTO SYNTH
[5] ISOLATOR
[6] SLICE
[7] TECH MODULATION
[8] CONTROL FILTER
No. Parameter Range Value Tbl No.
1 OSC Frequency Coarse 0.5 – 5kHz (0 – 127) 17
2 OSC Frequency Fine 0 – 127 (0 – 127)
3 LFO Wave Tri, Sine (0 – 1)
4 LFO Depth 0 – 127 (0 – 127)
5 LFO Speed 0.0Hz – 39.70Hz (0 – 127) 1
6 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
7 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 Modulator Input Level -∞dB – 0dB – +24dB (0 – 127) 45
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 143.
No. Parameter Range Value Tbl No.
1 Sensitivity 0 – 127 (0 – 127)
2 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
3 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
4 Attack Time 0.3ms – 227ms (0 – 127) 15
5 Release Time 2.6ms – 2171ms (0 – 127) 16
6 Release Curve 0 – 127 (0 – 127)
7 Direction Up, Down (0 – 1)
8 Dyna Threshold Level 0 – 127 (0 – 127)
9 Dyna Level Offset 0 – 127 (0 – 127)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 Side Chain Input Level -∞dB – 0dB – +24dB (0 – 127) 45
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 143.
No. Parameter Range Value Tbl No.
1 Filter Type LPF (12dB), LPF (18dB), LPF
(24dB), HPF, BPF, BEF
(0 – 5)
2 Sensitivity 0 – 127 (0 – 127)
3 Dyna Level Offset 0 – 127 (0 – 127)
4 Resonance -16 – +111 (0 – 127)
5 Attack Time 0.3ms – 227ms (0 – 127) 15
6 Release Time 2.6ms – 2171ms (0 – 127) 16
7 Release Curve 0 – 127 (0 – 127)
8 Direction up, down (0 – 1)
9 Dyna Threshold Level 0 – 127 (0 – 127)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 Side Chain Input Level -∞dB – 0dB – +24dB (0 – 127) 45
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 143.
No. Parameter Range Value Tbl No.
1 Mod Speed 0 – 127 (0 – 127)
2 Mod Wave Type TypeA, TypeB, TypeC,
TypeD
(0 – 3)
3 Mod Depth 0 – 127 (0 – 127)
4 Mod Depth Offset R -63 – +63 (1 – 127)
5 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
6 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
7 Delay Time 0.1ms – 370.0ms (1 – 3700)
8 Delay Time Offset R 0 – 884 (0 – 884)
9 Delay Level 0 – 127 (0 – 127)
10 Dry Mix Level 0 – 127 (0 – 127)
11 Feedback Level -63 – +63 (1 – 127)
12 FB Level Offset R -63 – +63 (1 – 127)
13 AM Speed 0.00Hz – 39.7Hz (0 – 127) 1
14 AM Wave Tri, Sine, Saw Up, Saw Down (0 – 3)
15 AM Depth 0 – 127 (0 – 127)
16 AM Inverse R Normal, Inverse (0 – 1)
No. Parameter Range Value Tbl No.
1 On/Off Switch On, Off (0 – 1)
2 Low Level -64 – +63 (0 – 127)
3 Mid Level -64 – +63 (0 – 127)
4 High Level -64 – +63 (0 – 127)
5 Low Mute Off, On (0 – 1)
6 Mid Mute Off, On (0 – 1)
7 High Mute Off, On (0 – 1)
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Tbl No.
1 Divide Type 16th – 4th (5 – 11) 13
2 Gate Time 0 – 100% (0 – 100)
3 Pan AEG Type A – E (0 – 4)
4 Pan AEG Min Level 0 – 127 (0 – 127)
5 Pan Depth -63 –+63 (1 – 127)
6 Divide Min Level 0 – 127 (0 – 127)
7 Pan Type A – J (0 – 9)
8 Drive 0 – 127 (0 – 127)
9 AEG Phase 0 – 15 (x 16th note) (0 – 15)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Phase Reset Off (free run), Key On Reset,
SEQ Start Reset
(0 – 2)
12 Set Slice Tempo — —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 143.
No. Parameter Range Value Tbl No.
1 Mod Speed 0 – 127 (0 – 127)
2 Mod Depth 0 – 127 (0 – 127)
3 Mod Gain -12 – +12dB (52 – 76)
4 Mod Mix Balance D63>W – D=W – D<W63 (1 – 127)
5 Pre Mod HPF Cutoff
Frequency
20Hz – 8.0kHz (0 – 52) 3
6 Mod LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
7 Mod LPF Resonance 1.0 – 12.0 (10 – 120)
8 Delay Time 0.1 – 740.0ms (1 – 7400)
9 Delay Time Offset R 0 – 884 (0 – 884)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Feedback Level -63 – +63 (1 – 127)
12 FB Level Offset R -63 – +63 (1 – 127)
13 Feedback Hi Damp 0.1 – 1.0 (1 – 10)
14 FB Hi Damp Offset R -0.9 – +0.9 (1 – 19)
15 —
16 —
No. Parameter Range Value Tbl No.
1 Filter Type LPF (12dB), LPF (18dB), LPF
(24dB), HPF, BPF
(0 – 4)
2 Cutoff Frequency Control 0 – 127 (0 – 127)
3 Resonance 0 – 127 (0 – 127)
4 Filter Output Level -12dB – +12dB (52 – 76)
5—
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 —
14 —
15 —
16 —