Data List

MONTAGE Data List
153
Effect Parameter List
[3] TEMPO PHASER
[4] DYNAMIC PHASER
[5] CONTROL PHASER
Category — TREMOLO&ROTARY
[1] AUTO PAN
[2] TREMOLO
[3] ROTARY SPEAKER 1
[4] ROTARY SPEAKER 2
Category — DISTORTION
[1] AMP SIMULATOR 1
No. Parameter Range Value Tbl No.
1 LFO Speed 16th – 4thx16 (5 – 29) 13
2 LFO Depth 0 – 127 (0 – 127)
3 Phase Shift Offset 0 – 127 (0 – 127)
4 Feedback Level -63 – +63 (1 – 127)
5 LFO Phase Reset Off (free run), Key On Reset,
SEQ Start Reset
(0 – 2)
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 150.
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Stage 4 – 22 (4 – 22)
12 Diffusion Mono, Stereo (0 – 1)
13 —
14 —
15 —
16 —
No. Parameter Range Value Tbl No.
1 Sensitivity 0 – 127 (0 – 127)
2 Dyna Level Offset 0 – 127 (0 – 127)
3 Feedback Level -63 – +63 (1 – 127)
4 Attack Time 0.3ms – 227ms (0 – 127) 15
5 Release Time 2.6ms – 2171ms (0 – 127) 16
6 Release Curve 0 – 127 (0 – 127)
7 Direction up, down (0 – 1)
8 Dyna Threshold Level 0 – 127 (0 – 127)
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Stage 4, 5, 6 (4 – 6)
12 Side Chain Input Level -∞dB – 0dB – +24dB (0 – 127) 45
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 150.
No. Parameter Range Value Tbl No.
1 Phase Control 0 – 127 (0 – 127)
2 Bottom 0 – 127 (0 – 127)
3 Top 0 – 127 (0 – 127)
4 Feedback 0 – 127 (0 – 127)
5 Stage 4, 6, 8, 10 (0 – 3)
6 Mode 1, 2 (0 – 1)
7 Color 0 – 127 (0 – 127)
8 Spread 0 – 127 (0 – 127)
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Tbl No.
1 LFO Speed 0.0Hz – 39.70Hz (0 – 127) 1
2 L/R Depth 0 – 127 (0 – 127)
3 F/R Depth 0 – 127 (0 – 127)
4 Pan Direction L<>R, L>>R, L<<R, L turn,
R turn, L/R
(0 – 5)
5 LFO Wave 0 – 28 (0 – 28)
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 150.
10 —
11 EQ Mid Frequency 100Hz – 10.0kHz (14 – 54) 3
12 EQ Mid Gain -12dB – +12dB (52 – 76)
13 EQ Mid Width 0.1 – 12.0 (1 – 120)
14 —
15 Input Mode Mono, Stereo (0 – 1)
16 —
No. Parameter Range Value Tbl No.
1 LFO Speed 0.0Hz – 39.70Hz (0 – 127) 1
2 AM Depth 0 – 127 (0 – 127)
3 PM Depth 0 – 127 (0 – 127)
4—
5—
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 150.
10 —
11 EQ Mid Frequency 100Hz – 10.0kHz (14 – 54) 3
12 EQ Mid Gain -12dB – +12dB (52 – 76)
13 EQ Mid Width 0.1 – 12.0 (1 – 120)
14 LFO Phase difference -180deg – +180deg (4 – 124)
15 Input Mode Mono, Stereo (0 – 1)
16 —
No. Parameter Range Value Tbl No.
1 Rotor Speed Slow 0.0Hz – 2.65Hz (0 – 63) 1
2 Horn Speed Slow 0.0Hz – 2.65Hz (0 – 63) 1
3 Rotor Speed Fast 0.0Hz – 39.70Hz (64 – 127) 1
4 Horn Speed Fast 0.0Hz – 39.70Hz (64 – 127) 1
5 Slow-Fast Time of Rotor 0 – 127 (0 – 127)
6 Slow-Fast Time of Horn 0 – 127 (0 – 127)
7 Drive Rotor 0 – 127 (0 – 127)
8 Drive Horn 0 – 127 (0 – 127)
9 Rotor/Horn Balance R63>H – R=H – R<H63 (1 – 127)
10 —
11 – 14: Same as the parameters shaded in gray in CROSS DELAY on page 150.
15 Mic L-R Angle 0deg – 180deg (0 – 60)
16 Speed Control Slow, Fast (0 – 1)
No. Parameter Range Value Tbl No.
1 Speed Control Slow, Fast (0 – 1)
2 Drive 0.0 – 10.0 (0 – 100)
3 Tone 0.0 – 10.0 (0 – 100)
4 Rotor/Horn Balance R63>H – R=H– R<H63 (1 – 127)
5 Output Level 0 – 127 (0– 127)
6 Mic L-R Angle 0deg, 90deg, 120deg,
180deg
(0 – 3)
7 Input Level -6dB – 0dB – +6dB (52 – 76)
8 Modulation Depth 0 – 63 (0 – 63)
9—
10 —
11 Slow-Fast Time of Horn x0.21 – x1.00 – x2.00 (14 – 127) 49
12 Fast-Slow Time of Horn x0.21 – x1.00 – x2.00 (14 – 127) 49
13 Rotor Speed Slow 0.0rpm – 88.3rpm (0 – 127) 56
14 Horn Speed Slow 0.0rpm – 89.6rpm (0 – 127) 57
15 Rotor Speed Fast 189.3rpm – 736.8rpm (1 – 127) 58
16 Horn Speed Fast 209.4rpm – 817.6rpm (1 – 127) 59
17 Slow-Fast Time of Rotor x0.21 – x1.00 – x2.00 (14 – 127) 49
18 Fast-Slow Time of Rotor x0.21 – x1.00 – x2.00 (14– 127) 49
No. Parameter Range Value Tbl No.
1 Overdrive 0 – 100% (0 – 100)
2 Device Transistor, Vintage Tube,
Distortion1, Distortion2, Fuzz
(0 – 4)
3 Speaker Type Flat, Stack, Combo, Twin,
Radio, Megaphone
(0 – 5)
4 Presence -10 – 10 (0 – 20)
5 Output Level 0 – 100% (0 – 100)
6—
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Tbl No.