Specifications

switched off. The Elements 3, 4, 5, and 6 are activated
ASSIGNABLE FUNCTION 2 = The Element 1 („Accordion“) is
switched off. The Element 2 („Tango Accordion“) is activated
Example: Pre2-030 (B14) Pop Bells & Pad MW
Element 1 = All AF off
ASSIGNABLE FUNCTION 1 = Element 1 („MedDetunedPadSt“) is
deactivated
ASSIGNABLE FUNCTION 2 = Element 1 („MedDetunedPadSt“)
is deactivated. In addition Elements 2 + 3 are played one octave
higher and are applied with a vibrato. This is programmed in Ctrl
Set (EDIT – COMMON – F4), not in the XA Control.
Example: Pre2-050 (D02) Classical AF1 & 2
Element 1 = All AF off
Element 2 = All AF off
Element 2 = All AF off
Element 4 = normal (Strumming-Effekt auf Taste C6)
Element 5 = key off sound
Element 6 = AF 1 on
Element 7 = AF 2 on
Element 8 = off (nicht verwendet)
ASSIGNABLE FUNCTION 1 = Elements 1, 2, and 3 are switched off.
Element 6 („Nylon Slide St“) is activated.
ASSIGNABLE FUNCTION 2 = Elements 1, 2, and 3 are switched off.
Element 7 („Nylon Harmonics St“) is activated.
While playing this Voice alternately press the ASSIGNABLE buttons 1
+ 2 to get the slide effect and the harmonics. These are realized by
switching on and switching off the Elements.
If AF1 is pressed, the Elements 1-3 are switched off, as they are set
to „all AF off“. At the same time Element 6 is turned on, because
this is set to „AF 1 on“.
If AF2 is pressed, the Elements 1 - 3 are also switched off. At the
same time Element 7 is switched on, because this is set to „AF 2
on“..
Example: Pre2-081 (F01) Dynamic Clean AF1&2
Element 1 = All AF off
Element 2 = All AF off
Element 4 = AF 1 on
Element 5 = AF 2 on
ASSIGNABLE FUNCTION 1 = The Elements 1 and 2 are switched
off. The Element 4 („Clean Mute“) is added
ASSIGNABLE FUNCTION 2 = The Elements 1 and 2 are switched
off. The Element 5 („Clean Slap“) is added
For the settings „all AF off“, „AF 1 on“, and „AF 2 on“ you have to
keep in mind, that the function of the ASSIGNABLE FUNCTION 1
+ 2 buttons may vary. Their function can be set in VOICE - EDIT
- COMMON - F1 General - SF3 Other using the parameters „A.
Function 1 Mode“ and „A. Function 2 Mode“. Here you can decide,
whether the AF buttons should function as latching or as a momentary
switches. When set to „latch“, pressing the button toggles between
on and off, which is indicated by the LED of the button. When set to
„momentary“ holding down the button switches on, while releasing
it switches off.
It is also important to know that AF1 + AF2 not only depend on
the XA Control settings of the Elements. Additionally or alterna-
tively they can have a parameter assigned to from the Control Set
(VOICE COMMON).
If you want to analyze further XA Voices which use the ASSIGNABLE
FUNCTION 1 + 2, you can recognize them by the „AF1&2“ in the
Voice name..
MEGA-vOICE-TECHNOLOGIE
The Mega Voice technology developed by Yamaha enables the
creation of ultra-realistic sounds thanks to an extremely elaborate
multi-sampling. Each Mega Voice consists of several multi-samples
or Elements combining velocity switches and key ranges. The Mega
Voices accommodate different playing techniques and noises of the
sampled instruments such as dead notes, hammer-on effects, ghost
notes and strumming.
On the MOTIF Mega Voices focus on acoustic guitars, electric guitars
and basses. The Mega Voice technology was first realized in the
Yamaha Tyros.
Due to their complex structure of keyboard and velocity limits Mega
Voices are very difficult to play. Therefore, special arpeggio patterns
have been programmed to control the Mega Voices.
You can find the Mega Voices in the Preset Voice Bank 8 (081 to
124).
Try the velocity zones and key splits to get an idea of the structure of
the Mega Voices..
EUROPE.YAMAHA.COM