User Manual
Table Of Contents
- Cover
- Introduction
- Setup workflow
- Example 1) Basic MTX3 system example (analog connections)
- Example 2) High audio quality system with XMV and YDIF connections (digital connections)
- Example 3) Using cascade mode to add MTX input channels (analog connection)
- Using the Device Configuration Wizard to create your device setup
- Making preliminary settings in MTX-MRX Editor
- Connecting the equipment
- Powering-on the MTX
- Powering-on the amp
- Setting the MCP1’s UNIT ID
- Specifying the computer’s TCP/IP address
- Taking MTX-MRX Editor online
- Making XMV settings
- Verifying that the settings were applied
- Example 4) A system using Dante
- Using the Device Configuration Wizard to create your device setup
- Making preliminary settings in MTX-MRX Editor
- Dante settings between systems
- Connecting the equipment
- Powering-on the MTX
- Powering-on the amp
- Specifying the computer’s TCP/IP address
- Taking MTX-MRX Editor online
- Making XMV settings
- Verifying that the settings were applied
- Example 5) A system using the PGM1 for paging
- Using the Device Configuration Wizard to create your device setup
- Making preliminary settings in MTX-MRX Editor
- Connecting the equipment
- Power-on the PoE-equipped gigabit network switch
- Power-on equipment other than amps and powered speakers
- Power-on amps and powered speakers
- Specifying the computer’s TCP/IP address
- Taking MTX-MRX Editor online
- Making XMV settings
- Verifying that the settings were applied
- Q&A
- Uninstalling the software (Removing the application)
Example 5) A system using the PGM1 for paging
MTX Setup Manual
141
Settings in the “MATRIX” screen
Here you can specify which input channel will be sent to which zone. For details on send level and other parameters,
refer to “MTX-MRX Editor User Guide.”
In this example, make the settings shown in the above illustration. Clicking or dragging a cross point (a square area)
will switch it on/off. Right-clicking a cross point will display a context menu. By selecting [All OFF] you can turn all
cross points off. The cross point shows the send level as the height of green.
With these settings, Event Space Mic1/2 are sent to the Event Space area, BGM (Luxury) is sent to the Luxury area,
BGM (Casual1) is sent to the Casual 1 area, BGM (Casual2) is sent to the Casual 2 area and Casual 3 area, BGM1 is
sent to the Food Court area, and BGM2 is sent to the Entrance area and the Restrooms area.
The PGM1 which is assigned to CH1 is specified in the following “ZONE” screen. If CH1 is turned on in MATRIX,
the input from PGM1 is output to the zone even if PTT is off.
The input channel faders in the lower left of the screen indicate the input level for faders that are grayed-out, and indi-
cate the input channel send level for faders that are not grayed-out. Grayed-out faders cannot be operated in this screen.
Paging signal flow
*1 DISTRIBUTION MODE only
PAGING
SOURCE
PRIORITY
SOURCE
PRIORITY
SOURCE
AMBIENT
SOURCE
PRIORITY
DUCKER
ANC
GR GR
PAGING
DUCKER
PRIORITY
DUCKER
MIXMIX
MIX
ZONE OUT
MASTER
LEVEL
METER
8
METER
AMBIENT
ANC1st PRIORITY
PAGING
2nd PRIORITY
ON
ZONE 1-8
To YDIF
OUTPUT
PATCH
From INPUT CHANNEL POST ON 1-16
From DIRECT INPUT POST ON 9-16
From ANC BUS 1-2
*1 From YDIF IN 1-16
From STEREO INPUT CHANNEL POST ON 1L-3R
D
C
A