User Manual
Table Of Contents
- Cover
- Introduction
- Setup workflow
- Example 1) Basic MTX3 system example (analog connections)
- Example 2) High audio quality system with XMV and YDIF connections (digital connections)
- Example 3) Using cascade mode to add MTX input channels (analog connection)
- Using the Device Configuration Wizard to create your device setup
- Making preliminary settings in MTX-MRX Editor
- Connecting the equipment
- Powering-on the MTX
- Powering-on the amp
- Setting the MCP1’s UNIT ID
- Specifying the computer’s TCP/IP address
- Taking MTX-MRX Editor online
- Making XMV settings
- Verifying that the settings were applied
- Example 4) A system using Dante
- Using the Device Configuration Wizard to create your device setup
- Making preliminary settings in MTX-MRX Editor
- Dante settings between systems
- Connecting the equipment
- Powering-on the MTX
- Powering-on the amp
- Specifying the computer’s TCP/IP address
- Taking MTX-MRX Editor online
- Making XMV settings
- Verifying that the settings were applied
- Example 5) A system using the PGM1 for paging
- Using the Device Configuration Wizard to create your device setup
- Making preliminary settings in MTX-MRX Editor
- Connecting the equipment
- Power-on the PoE-equipped gigabit network switch
- Power-on equipment other than amps and powered speakers
- Power-on amps and powered speakers
- Specifying the computer’s TCP/IP address
- Taking MTX-MRX Editor online
- Making XMV settings
- Verifying that the settings were applied
- Q&A
- Uninstalling the software (Removing the application)
MTX Setup Manual 7
The following table shows the workflow for connecting equipment such as MTX series matrix mixers and XMV series
power amplifiers to your computer, and making settings in MTX-MRX Editor.
Installing MTX-MRX Editor
In order to connect MTX series devices to your computer, you’ll need to download MTX-MRX Editor from the “down-
load” page of the Yamaha Pro Audio website.
http://www.yamahaproaudio.com/
System Requirements
Example 1 Example 2 Example 3 Example 4 Example 5
Installing MTX-MRX Editor Page 7
Starting up MTX-MRX Editor Page 8
Using the Device Configuration Wizard to create your device
setup
Page 9 Page 30 Page 55 Page 82 Page 125
Making pre-
liminary set-
tings in
MTX-MRX
Editor
Making EXT. I/O settings
YDIF — Page 35 — Page 94 —
XMV (Analog) — — Page 60 — —
XMV (Dante) — — — Page 106 Page 132
Parameter settings for the MTX and external
devices (Parameter settings such as for jacks
and channels)
Page 14 Page 39 Page 63
Page
98, 111
Page 136
Settings in the “DCA” screen
(Settings that control the level or mute of multiple
channels in a single operation)
— — Page 72 — —
Digital Control Panel (DCP) settings Page 21 Page 46 — — —
MCP1 settings — — Page 73 — —
Storing a preset (Presets and recall filter settings) Page 23 Page 48 Page 74 Page 117 Page 148
Dante settings between systems — — — Page 114 —
Connecting the equipment Page 26 Page 51 Page 77 Page 118 Page 149
Power-on the devices in order Page 26 Page 52 Page 78 Page 120 Page 150
Setting the MCP1’s UN IT ID — — Page 78 ——
Specifying the computer’s TCP/IP address Page 27 Page 52 Page 78 Page 120 Page 150
Taking MTX-MRX Editor online Page 28 Page 53 Page 79 Page 122 Page 152
Making XMV settings — Page 54 Page 80 Page 122 Page 152
Verifying that the settings were applied Page 29 Page 54 Page 80 Page 123 Page 153
OS Windows 10 (32bit/64bit)
CPU Core i3/5 or better
Memory 4 GB or more
H.D.D 230 MB or more free (When you install, need 480 MB or more free.)
Other Bonjour must be installed, Ethernet (1000BASE-T or higher)
NOTE
The System Requirements described above are applied to the MTX-MRX Editor version 4.0.0. You can check the latest version infor-
mation of each program and its system requirements at the following website
http://www.yamahaproaudio.com/
The system requirements may differ slightly depending on the particular computer.
Setup workflow