User Manual
Table Of Contents
- Notice regarding data copyright
- Notice regarding the content of this user guide
- Contents
- Chapter 1. An overview of MTX-MRX Editor
- An audio system control network
- Terms used in this user guide
- Data handled by MTX-MRX Editor
- Connection requirements for an MTX/MRX system
- MTX/MRX system configuration examples
- What are YDIF connections? (Cascade mode and Distribution mode)
- What are Dante connections? (Daisy-chain connection and Star connection)
- Patching
- Workflow
- About the screens
- Moving between screens
- Chapter 2. Menu bar and tool buttons
- Chapter 3. Project screen
- Chapter 4. System screen
- Chapter 5. Online and Synchronization
- Chapter 6. Presets
- Chapter 7. Dialog boxes/Software applications
- “Startup” dialog box
- “Network Setup” dialog box
- “Device Information” dialog box
- “Match Device by IP Address” dialog box
- “MTX Configuration” dialog box
- “Dante Information” dialog box
- “Word Clock” dialog box
- “Clock” dialog box
- “Daylight Saving Time” dialog box
- “Scheduler” dialog box
- “Remote Control” dialog box
- “External Events” dialog box
- “Digital Control Panel” dialog box
- “Wireless DCP” dialog box
- “MCP1” dialog box
- “PIN Setup” dialog box
- “Label” dialog box
- “Re-size Image” dialog box
- “PGM1/PGX1” dialog box
- “PGM1 Label Creator” application
- “GPI” dialog box
- “GPI Calibration” dialog box
- “Security Settings” dialog box
- “Project Information” dialog box
- “Configuration Diagram” dialog box
- “Get Log” dialog box
- “Sampling Rate Converter” dialog box
- “Input Source/Redundant” dialog box
- Appendix
“Word Clock” dialog box Chapter 7. Dialog boxes/Software applications
MTX-MRX Editor User Guide
182
The following devices are not shown.
• EXi8
•Exo8
• XMV units connected via YDIF
• XMV units connected via analog
● [Device Word Clock Fs:]
This indicates the word clock of the device. When online, this indicates the word clock
value for the device. When offline, the indication will be as follows.
● [Clock Source]
Use these buttons to select the word clock source. A indicator showing the status is
displayed at the left of buttons that can be selected. When offline the status cannot be
detected, so all indicators will be yellow.
● [Dante]
Specifies the Dante word clock. If the device is set to Device Lock by Dante Controller,
a lock icon is shown, and settings cannot be made.
• [Word Clock Fs:] box
Indicates/specifies the word clock of the device. If the unit is set to Device Lock by
Dante Controller, a lock icon is shown, and the unit is excluded from editing. If the
unit is set to AES67 mode by Dante Controller, this indicates “48kHz,” and the unit
is excluded from editing.
• [Preferred Master] check box
Selecting this check box will increase the probability that the device will become the
clock master within the Dante network. Use this when the MTX/MRX system
includes a Dante device that is not supported by MTX-MRX Editor, and you want
to use the MTX/MRX system device as the clock master. If the unit is set to Device
Lock by Dante Controller, the unit is excluded from editing.
● [Close] button
Closes the dialog box.
Icon Clock source
Dante
Internal
Mini-YGDAI card
None YDIF
MTX5-D/MRX7-D
If DANTE is specified as the word clock source, this indicates
the value specified by Dante [Word Clock Fs:].
Otherwise, this indicates “---”.
MTX3
If Internal 44.1 kHz or 48 kHz are selected, that value is shown.
If YDIF is selected, this indicates “---”.
Dante-compatible XMV This indicates “48 kHz”.
Indicator Status
Locked.
Locked but not synchronized.
Unlocked.
The clock status cannot be detected because an external
device is not connected or because there is no valid clock input.
NOTE