User Manual
Table Of Contents
- Notice regarding data copyright
- Notice regarding the content of this user guide
- Contents
- Chapter 1. An overview of MTX-MRX Editor
- An audio system control network
- Terms used in this user guide
- Data handled by MTX-MRX Editor
- Connection requirements for an MTX/MRX system
- MTX/MRX system configuration examples
- What are YDIF connections? (Cascade mode and Distribution mode)
- What are Dante connections? (Daisy-chain connection and Star connection)
- Patching
- Workflow
- About the screens
- Moving between screens
- Chapter 2. Menu bar and tool buttons
- Chapter 3. Project screen
- Chapter 4. System screen
- Chapter 5. Online and Synchronization
- Chapter 6. Presets
- Chapter 7. Dialog boxes/Software applications
- “Startup” dialog box
- “Network Setup” dialog box
- “Device Information” dialog box
- “Match Device by IP Address” dialog box
- “MTX Configuration” dialog box
- “Dante Information” dialog box
- “Word Clock” dialog box
- “Clock” dialog box
- “Daylight Saving Time” dialog box
- “Scheduler” dialog box
- “Remote Control” dialog box
- “External Events” dialog box
- “Digital Control Panel” dialog box
- “Wireless DCP” dialog box
- “MCP1” dialog box
- “PIN Setup” dialog box
- “Label” dialog box
- “Re-size Image” dialog box
- “PGM1/PGX1” dialog box
- “PGM1 Label Creator” application
- “GPI” dialog box
- “GPI Calibration” dialog box
- “Security Settings” dialog box
- “Project Information” dialog box
- “Configuration Diagram” dialog box
- “Get Log” dialog box
- “Sampling Rate Converter” dialog box
- “Input Source/Redundant” dialog box
- Appendix
Data handled by MTX-MRX Editor Chapter 1. An overview of MTX-MRX Editor
MTX-MRX Editor User Guide
6
Data handled by MTX-MRX Editor
Even if you modify the configuration, the changes will not be reflected in previously-stored
presets. After modifying a configuration, you must (if necessary) recall the preset and then
store it again.
Project file (.mtx)
Configuration
Device structure
*1
The type and number of devices, their UNIT ID, and YDIF connection order
MTX/MRX system settings
*2
YDIF mode
Device name
“Preset” dialog box
“Security Setting” dialog box ([File] menu)
“Project Information” dialog box ([File] menu)
Contents of “Set IP Address” in the “Device Information” dialog box ([System]
menu)
“MTX Configuration” dialog box ([System] menu)
“Daylight Saving Time” dialog box ([System] menu)
“Scheduler” dialog box ([System] menu)
“GPI” dialog box ([System] menu)
“Remote Control” dialog box ([System] menu)
“External Events” dialog box ([Controller] menu)
Library of the “Digital Control Panel” dialog box ([Controller] menu)
Library of the “Wireless DCP” dialog box ([Controller] menu)
Function Assign of the “PGM1/PGX1” dialog box ([Controller] menu)
Dimmer on/off and Input Source/Redundant settings ([Device] tab)
Patching in the “EXT. I/O” screen between the MTX/MRX and external devices
(YDIF connections, analog connections, Dante connections)
Pilot Tone setting in the [I/O] screen
*1 Synchronization is not possible if the device configuration is different.
*2 This will not change even if the preset is switched.
Preset
MTX/MRX sources for YDIF in the “EXT. I/O” screen
Parameters
*3
for MTX/MRX components
Assignments to DCP library presets
Assignments to Wireless DCP library presets
Assignments to MCP1 library presets
GPI Out status
[SD Song Select & Play]
Parameters of the EXi8/EXo8/XMV/R series (AD/DA)/Tio1608-D
MY4-AEC parameters (except for AES/EBU)
*3 The MRX’s component parameters are managed as snapshots of parameter sets.
They are associated with presets by registering a snapshot in a preset. For more
about snapshots, refer to “MRX Designer User Guide.”
Speaker Processor Library (.ce3)
NOTE