User Manual
Table Of Contents
- Contents
- An overview of MRX Designer
- Screen structure
- Basic use of MRX Designer
- Menu bar
- Tool buttons
- Shortcut keys
- Design sheet
- “Parameter Sets” area
- “Parameter Link Group” area
- “Gang Edit Group” area
- “Properties” area
- Components and the component editor
- Editing the parameters
- Acoustic Echo Canceller (AEC)
- Ambient Noise Compensator (ANC)
- Audio Detector
- Auto Gain Controller (AGC)
- Combiner
- Delay
- Dynamics
- Effect
- EQ
- Fader
- Feedback Suppressor
- Filter
- Inputs/Outputs
- Meter
- Mixer
- Oscillator
- Paging
- Polarity
- Revolabs Control
- Router
- Source Selector
- Speaker Processor
- Speech Privacy
- Text
- Transmitter/Receiver
- User Defined Block
- Dialog boxes and applications
- “Print” dialog box
- “Install Speech Privacy File” dialog box
- “File Transfer” application
- “PGM1 Label Creator” application
- “Compile” dialog box
- “Snapshot Group” dialog box
- “Remote Control Setup List” dialog box
- “External Events” dialog box
- “GPI” dialog box
- “Digital Control Panel” dialog box / “Wireless DCP” dialog box / “MCP1” dialog box
- “PGM1/PGX1” dialog box
- “Port Name” dialog box
- List of settings in “Settings” dialog boxes
- Context menus
- Troubleshooting
Menu bar
MRX Designer User Guide
15
Controller
[External
Events]
Enables you to configure the commands to be
transmitted so that you can control peripheral
devices via the network to which the Dante
connector or NETWORK connector is
connected. For details, refer to “MTX-MRX Editor
User Guide.”
“External Events” dialog
box
[GPI]
Lets you make settings for the GPI connector of
the MRX. For details, refer to “MTX-MRX Editor
User Guide.”
“GPI” dialog box
[Digital Control
Panel]
Lets you make settings for a DCP.
“Digital Control Panel”
dialog box / “Wireless
DCP” dialog box / “MCP1”
dialog box
[Wireless DCP] Lets you make settings for a Wireless DCP. “Port Name” dialog box
[MCP1] Lets you make settings for an MCP1. “MCP1” dialog box
[PGM1/PGX1] Lets you make settings for a PGM1/PGX1. “PGM1/PGX1” dialog box
[Arrange]
[Align Left
Sides]
Aligns the left side to the left-most component of
the selected multiple components.
—
[Align
Horizontal
Centers]
Aligns the center of the component to the
horizontal center of the selected multiple
components.
—
[Align Right
Sides]
Aligns the right side to the right-most component
of the selected multiple components.
—
[Align Tops]
Aligns the top side to the highest of the selected
multiple components.
—
[Align Vertical
Centers]
Aligns the center of the component to the vertical
center of the selected multiple components.
—
[Align Bottoms]
Aligns the bottom side to the lowest of the
selected multiple components.
—
[Distribute
Horizontally]
Spaces the selected components evenly in the
horizontal direction.
—
[Distribute
Vertically]
Spaces the selected components evenly in the
vertical direction.
—
[Same Heights]
Aligns the height of the selected components.
Depending on the number of ports, the height
might not align.
—
[Same Widths]
Aligns the width of the selected components.
Depending on the port name, the width might not
align.
—
[Bring to Front]
Moves the selected component or wire to the front.
—
[Send to Back]
Moves the selected component or wire to the
back.
—
Menu Command Summary
Dialog box or window
that appears