User Manual
Table Of Contents
- Cover
- Introduction
- Setup workflow
- Example 1) Ballroom where the Room Combiner can be used
- Example 2) Remote conferencing system that also uses Speech Privacy
- Using the Device Configuration Wizard to create your device setup
- Configuring the settings on the MRX
- Making EXT. I/O settings
- Connecting the equipment
- Powering-on the MRX
- Powering-on the amp
- Specifying the computer’s TCP/IP address
- Sending the Speech Privacy environmental sound
- Taking MTX-MRX Editor online
- Verifying that the settings were applied
- Example 3) A paging system using the PGM1
- Using the Device Configuration Wizard to create your device setup
- Specifying the MRX configuration
- Making EXT. I/O settings
- Connecting the equipment
- Powering-on the PoE-equipped gigabit network switch
- Specifying the MCP1’s UNIT ID
- Power-on equipment other than amps and powered speakers
- Power-on amps and powered speakers
- Specifying the computer’s TCP/IP address
- Taking MTX-MRX Editor online
- Verifying that the settings were applied
- Q&A
- Uninstalling the software (Removing the application)
Example 1) Ballroom where the Room Combiner can be used
MRX Setup Manual
42
Allocates parameters to the DCP4V4S and DCP4S in each room, so that they can be changed by operating a switch or
knob.
Set the library name to “Room Split” if the room is split, and to “Room Combine” if the rooms are combined.
Allocate the following parameters to the switches and knobs. (The steps for allocating parameters will be explained later.)
“Room Split” parameters
* The preset has not been configured at this time, so only the preset number is displayed. By recalling the preset, you will be able to
tell which preset was recalled by looking at the indicator on the DCP4S switch. (When using the DCP switch to switch the Combine
button on and off, you won’t be able to tell whether it is on or off just by looking at the DCP.)
For the “Room Combine” parameters, use the “Room Split” parameters, but change the red characters to “1” or “A.”
Now, we’ll explain how to set the parameters for switch 1 (parameter) of the DCP4V4S, and for switch 1 (preset) of the
DCP4S in Room A. This time, we’ll explain how to do this by dragging and dropping the parameters while holding <Ctrl>
using the component editor and so on; but you can also drag and drop from the “Parameters” area while holding <Ctrl>.
Making the DCP settings
DCP Switch/knob
Component, snapshot, or parameter link group
that includes the set parameter
Parameters
DCP4V4S for
Room A
Switch 1 Room Combiner plus Automixier Mics [ON] button for Room 1
Switch 2 Room Combiner plus Automixer BGM [ON] button for Room 1
Switch 3 RoomA BD-AUX On/Off for parameter link group [ON] button for Link Master
Switch 4 RoomA Matrix On/Off for parameter link group [ON] button for Link Master
Knob 1 Room Combiner plus Automixier Mics knob for Room 1
Knob 2 Room Combiner plus Automixier BGM knob for Room 1
Knob 3 RoomA BD Level for parameter link group Link Master fader
Knob 4 RoomA Aux Level for parameter link group Link Master fader
DCP4S for
Room A
Switch 1 Preset 01 Split *
Switch 2 Preset 02 Combine *
Switch 3 Room Combiner plus Automixier Room 1 BGM list (Inc/Upper Limit=4)
Switch 4 Room Combiner plus Automixier Room 1 BGM list (Dec)
DCP4V4S for
Room B
Switch 1 Room Combiner plus Automixier Mics [ON] button for Room 2
Switch 2 Room Combiner plus Automixier BGM [ON] button for Room 2
Switch 3 RoomB BD-AUX On/Off for parameter link group [ON] button for Link Master
Switch 4 RoomB Matrix On/Off for parameter link group [ON] button for Link Master
Knob 1 Room Combiner plus Automixier Mics knob for Room 2
Knob 2 Room Combiner plus Automixier BGM knob for Room 2
Knob 3 RoomB BD Level for parameter link group Link Master fader
Knob 4 RoomB Aux Level for parameter link group Link Master fader
DCP4S for
Room B
Switch 1 Preset 01 Split *
Switch 2 Preset 02 Combine *
Switch 3 Room Combiner plus Automixier Room 2 BGM list (Inc/Upper Limit=4)
Switch 4 Room Combiner plus Automixier Room 2 BGM list (Dec)