User Manual
Table Of Contents
- Notice regarding data copyright
- Notice regarding the content of this user guide
- Contents
- Chapter 1. An overview of MTX-MRX Editor
- An audio system control network
- Terms used in this user guide
- Data handled by MTX-MRX Editor
- Connection requirements for an MTX/MRX system
- MTX/MRX system configuration examples
- What are YDIF connections? (Cascade mode and Distribution mode)
- What are Dante connections? (Daisy-chain connection and Star connection)
- Patching
- Workflow
- About the screens
- Moving between screens
- Chapter 2. Menu bar and tool buttons
- Chapter 3. Project screen
- Chapter 4. System screen
- Chapter 5. Online and Synchronization
- Chapter 6. Presets
- Chapter 7. Dialog boxes/Software applications
- “Startup” dialog box
- “Network Setup” dialog box
- “Device Information” dialog box
- “Match Device by IP Address” dialog box
- “MTX Configuration” dialog box
- “Dante Information” dialog box
- “Word Clock” dialog box
- “Clock” dialog box
- “Daylight Saving Time” dialog box
- “Scheduler” dialog box
- “Remote Control” dialog box
- “External Events” dialog box
- “Digital Control Panel” dialog box
- “Wireless DCP” dialog box
- “MCP1” dialog box
- “PIN Setup” dialog box
- “Label” dialog box
- “Re-size Image” dialog box
- “PGM1/PGX1” dialog box
- “PGM1 Label Creator” application
- “GPI” dialog box
- “GPI Calibration” dialog box
- “Security Settings” dialog box
- “Project Information” dialog box
- “Configuration Diagram” dialog box
- “Get Log” dialog box
- “Sampling Rate Converter” dialog box
- “Input Source/Redundant” dialog box
- Appendix
How the settings in each dialog box relate to the “YDIF” screen Chapter 4. System screen
MTX-MRX Editor User Guide
122
How the settings in each dialog box relate to the “YDIF”
screen
About YDIF
When connected via YDIF, the XMV will send the audio signals without change to the
EXi8/EXo8 or the MTX/MRX. The audio signal will loop unless the EXi8/MTX/MRX
unit outputs a different signal or the output is stopped.
8
YDIF
OUTPUT
PATCH
From INPUT CHANNEL POST ON 1-8
From THRU 1-16
From ZONE OUT 1-8
From STEREO INPUT CHANNEL POST ON 1L-3R
16
8
*DISTRIBUTION MODE only
*CASCADE MODE only
YDIF OUT
YDIF OUT
YDIF MODE
CASCADE MODE
or DISTRIBUTION MODE
8
6
8
16
YDIF
OUT
YDIF2
YDIF1
#03 EXi8
CH1
OUT
OUT
OUT
OUT
OUT
OUT OUT
IN
IN
IN
IN
IN
IN IN
#04 EXi8
#01 MTX3
#02 MTX3
#30 XMV
#31 XMV
#03 EXi8
OUT
OUT
OUT
OUT
OUT
IN
IN
IN
IN
IN
#04 EXi8
#01 MTX3
#02 MTX3
#30 XMV
#31 XMV
OUT8
CH A&B
MTX3 ID=02
MTX3 ID=01
XMV4280 ID=31
XMV4280 ID=30
EXi8 ID=03
EXi8 ID=04
Network
Swich
No output No output
No output
No output
Through
Through
Through
Through
Through
Through
Through
Through
Through
Through
CH C
OUT1
“YDIF Out Patch” dialog box
“Channel Select” dialog box
“YDIF In Patch” dialog box
YDIF signal flow with the settings shown above