User Manual
Table Of Contents
- Notice regarding data copyright
- Notice regarding the content of this user guide
- Contents
- Chapter 1. An overview of MTX-MRX Editor
- An audio system control network
- Terms used in this user guide
- Data handled by MTX-MRX Editor
- Connection requirements for an MTX/MRX system
- MTX/MRX system configuration examples
- What are YDIF connections? (Cascade mode and Distribution mode)
- What are Dante connections? (Daisy-chain connection and Star connection)
- Patching
- Workflow
- About the screens
- Moving between screens
- Chapter 2. Menu bar and tool buttons
- Chapter 3. Project screen
- Chapter 4. System screen
- Chapter 5. Online and Synchronization
- Chapter 6. Presets
- Chapter 7. Dialog boxes/Software applications
- “Startup” dialog box
- “Network Setup” dialog box
- “Device Information” dialog box
- “Match Device by IP Address” dialog box
- “MTX Configuration” dialog box
- “Dante Information” dialog box
- “Word Clock” dialog box
- “Clock” dialog box
- “Daylight Saving Time” dialog box
- “Scheduler” dialog box
- “Remote Control” dialog box
- “External Events” dialog box
- “Digital Control Panel” dialog box
- “Wireless DCP” dialog box
- “MCP1” dialog box
- “PIN Setup” dialog box
- “Label” dialog box
- “Re-size Image” dialog box
- “PGM1/PGX1” dialog box
- “PGM1 Label Creator” application
- “GPI” dialog box
- “GPI Calibration” dialog box
- “Security Settings” dialog box
- “Project Information” dialog box
- “Configuration Diagram” dialog box
- “Get Log” dialog box
- “Sampling Rate Converter” dialog box
- “Input Source/Redundant” dialog box
- Appendix
Alert list Appendix
MTX-MRX Editor User Guide
271
47
Event [**] could not be
transmitted.
Check the devices that are connected to the
network.
Error Single
50
The UNIT ID is set to “00.” Set the UNIT ID to something other than “00.” Error Continuing
51
Devices with identical UNIT IDs
were found connected within
the same network.
Change the UNIT ID so that there are no
duplicates.
Error Continuing
52
A communication error
occurred with the [DCP]
connection.
• If an error was shown in the DCP panel,
refer to the DCP owner’s manual and take
the appropriate action.
• Ensure that the panel ID of the DCP units
do not conflict.
• Verify that the cables are correctly
connected and are within the specified
length.
Error Single
53
The DCP[*] connected to the
[DCP] connector has been
configured differently from the
project settings.
• Check that the required DCP is connected.
• Check whether a different model of DCP
might be connected.
Error Continuing
56
SD memory card was not
recognized.
Use an SD memory card that complies with
the specifications.
Error Continuing
58
Unable to play the specified file
or folder in the SD player.
Verify that the specified audio file or folder
exists in the SD memory card. There must be
at least one playable audio file in the specified
folder.
Warning Single
60
A preset recall attempt has
failed.
Initialize the memory of the device (use rear
panel DIP switches 7 and 8). If this does not
solve the problem, contact your Yamaha
dealer.
Error Continuing
61
The recall could not be
executed because the preset to
be recalled when the MTX/
MRX starts up was not found.
Specify a preset that exists. No sound will be
output unless an appropriate preset is
recalled.
Error Continuing
62
A snapshot/snapshot group
recall attempt has failed.
Initialize the memory of the device (use rear
panel DIP switches 7 and 8). If this does not
solve the problem, contact your Yamaha
dealer.
Error Continuing
63
The snapshot/snapshot group
could not be recalled.
• The Snapshot selected for recall cannot be
recalled as no data has been stored to it.
• Another device may have been added after
snapshots were stored. Please synchronize
and check all snapshots/snapshot groups
using Editor, edit as necessary and store
again.
Warning Single
64
The preset could not be
recalled.
• The Preset selected for recall cannot be
recalled as no data has been stored to it.
• Another device may have been added after
presets were stored. Please synchronize
and check all presets using MTX-MRX
Editor, edit as necessary and store again.
Warning Continuing
65
Invalid parameters set for GPI
IN.
Check the GPI IN settings and perform
synchronization again.
Error Continuing
66
Invalid parameters set for GPI
OUT.
Check the GPI OUT settings and perform
synchronization again.
Error Continuing
Number Content Action Type
Single/
Continuing