English Deutsch L2 Switch Español Français SWR2100P-10G SWR2100P-5G Русский Italiano Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones Manuale di istruzioni Руководство пользователя EN DE FR ES IT RU
ATTENTION RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. ATTENTION : POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION, FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PRECAUTIONS PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/power cord • Do not damage the power cable or the LAN cable.
Do not open If you notice any abnormality • This device contains no user-serviceable parts. Do not open the device or attempt to disassemble the internal parts or modify them in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. • If any of the following problems occur, disconnect the electric plug from the outlet. - The power cord or plug becomes frayed or damaged. - Unusual smells or smoke are emitted.
PRECAUTIONS CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Power supply/power cord • When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.
NOTICE To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below. • Be sure to earth (ground) any static electricity from your body or clothing before touching the product. Failure to observe this precaution could result in damage to the product. Handling and maintenance • Do not install the product in a location where magnetic fields are strong. Otherwise, it might cause the product to malfunction.
NOTICE About this manual • The illustrations as shown in this manual are for instructional purposes only. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. • Software may be revised and updated without prior notice. Open Source Software Used in this Product • Please refer to Yamaha Pro Audio website for the details of licensing article. http://www.yamaha.
PRECAUTIONS ......................................................................................................... 4 NOTICE ..................................................................................................................... 7 Introduction .............................................................................................................10 Features...................................................................................................................10 Accessories ..
Introduction Thank you for purchasing the Yamaha SWR2100P-10G or SWR2100P-5G, an L2 switch. This product supplies power to PoE powered devices on the network. This owner’s manual explains how to install and set up the unit. It is intended for installers or facility designers. Please be sure to read this manual before you start using the product to take full advantage of its features. Please retain this manual in a safe location for future reference.
English Controls and Connectors Front panel ■ SWR2100P-10G 1 3 2 5 4 6 7 6 7 ■ SWR2100P-5G 1 3 2 4 5 1 POWER indicator Lights up when power is provided to the unit. POWER indicator Power Light off OFF Light on (green) ON 2 PoE LIMIT indicator Indicates the status of maximum power supply.
If the total power supply is 63W or higher but lower than 70W (in this case, the PoE LIMIT indicator will light up steadily in green), you will be unable to increase the number of powered devices to which power is supplied. Therefore, if you connect a powered device to a higher-priority port on the unit, power will be supplied to that powered device, but will not be supplied to a powered device connected to a lower-priority port.
These are ports for 10BASE-T, 100BASE-TX, and 1000BASE-T. Port #10 on the SWR2100P-10G and port #5 on the SWR2100P-5G are uplink ports, and do not provide a power supply function. 7 CONFIGURATION switch Sets enabling/disabling of functions. Please refer to “Setting the CONFIGURATION switches” (page 16). Top panel Serial number MAC address 8 8 Product label Indicates the equipment name, serial number, MAC address, etc. of the unit.
Rear panel Serial number 9 0 9 Holes for attaching the power cord clamp Attach the included power cord clamp (U-shaped type). For information about the attachment method, please refer to “Connections” (page 19). 0 Power inlet (3 poles connector, C14-type) Insert the included power cord. Connect to outlets between AC 100V and AC 240V (50/60 Hz).
English Bottom panel A B A A Rubber feet installation guide The following figure shows the position of the included feet when the unit is placed horizontally upside-down. When placing the unit horizontally, please attach the included feet as indicated in the figure. Feet Rubber feet installation Rubber feet B Attachment holes for the rack-mount accessory Use these holes to attach the RK-SWR rack-mount accessory.
Setting the CONFIGURATION switches You can enable or disable functions for this unit by setting the CONFIGURATION switches. In order to operate the switches, please use something round, such as the tip of a ballpoint pen or small screwdriver. This unit reads the switch status at startup and enables or disables functions as indicated. If the switch status is changed after startup, the new switch status will be in effect at the next startup.
This section explains how to attach an optional RK-SWR rack mount accessory to the unit. Please read before mounting the unit into a rack This unit is guaranteed to operate properly at 0–40 degree Celsius (32–104 degrees Fahrenheit). If you install this unit along with other devices into an EIA-standard rack, the temperature inside the rack may rise due to heat released from the other devices, resulting in poor performance of the unit.
2. Installing the rack mount panel to the 19-inch rack Use four screws (supplied with an EIA-standard 19-inch rack) to mount the unit into the rack. Be sure to tighten the screws so that they will not get loosened. 19-inch rack Screws supplied with the 19-inch rack Rack mount panel You can also mount two units as shown in the figure below.
1. English Connections Connect the LAN port of the network device to the LAN port of this product using a LAN cable. 2. Connect the power cord to a power inlet. Notice • We recommend that you attach the supplied power cord clamp to prevent the power cord from accidentally being disconnected. • This clamp is used only for the supplied power cord. If you use the clamp for other power cords, they might be damaged or might not secure properly. 1 Insert the included 2 Raise the clamp.
Appendix Hardware specifications Items SWR2100P-10G External dimensions (W x D x H, Unit: mm) Weight Number of ports Ports available for PoE power supply 5 ports 9 ports (port 1–9) 4 ports (port 1–4) Power supply system Alternative A Per port 30W (Varies depending on the power consumption class of each connected powered device.
250 2.3 English Dimensions 40.5 43.5 220 Unit: mm * The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file.
Software license agreement This License Agreement (the “AGREEMENT”) is a legal agreement between you and Yamaha Corporation (“YAMAHA”) under which YAMAHA is providing the firmware of YAMAHA’s network products (the “PRODUCT”) and related software program, documentation and electronic files (collectively, the “SOFTWARE”). YAMAHA grants you a personal non-exclusive license to use the SOFTWARE only for purposes of running it on the PRODUCT.
5-3. YAMAHA, YAMAHA’S SUBSIDIARIES AND AFFILIATES, THEIR DISTRIBUTORS AND DEALERS SHALL HAVE NO OBLIGATION TO INDEMNIFY YOU AGAINST ANY CLAIM OR SUIT BROUGHT BY A THIRD PARTY ALLEGING THAT THE SOFTWARE OR USE THEREOF INFRINGES ANY INTELLECTUAL PROPERTY OF SUCH THIRD PARTY. 6. TERM: 6-1. This AGREEMENT becomes effective upon your agreeing to the terms and conditions herein and continues in effect unless or until terminated in accordance with the provision of 6-2 or 6-3 herein. 6-2.
124 SWR2100P-10G/SWR2100P-5G Owner’s Manual
Information for users on collection and disposal of old equipment: This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation.
Información para usuarios sobre la recogida y eliminación de los equipos antiguos Este símbolo en los productos, embalajes y documentos anexos significa que los productos eléctricos y electrónicos no deben mezclarse con los desperdicios domésticos normales. Para el tratamiento, recuperación y reciclaje apropiados de los productos antiguos, llévelos a puntos de reciclaje correspondientes, de acuerdo con la legislación nacional.
ADDRESS LIST NETHERLANDS/BELGIUM/ LUXEMBOURG NORTH AMERICA CANADA Yamaha Music Europe Branch Benelux Clarissenhof 5b, 4133 AB Vianen, The Netherlands Tel: +31-347-358040 Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario, M1S 3R1, Canada Tel: +1-416-298-1311 FRANCE U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A. Tel: +1-714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México, S.A. de C.V. Av. Insurgentes Sur 1647 Piso 9, Col.
Yamaha Pro Audio global website https://www.yamaha.com/proaudio/ Yamaha Downloads https://download.yamaha.