User Manual

MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specications V4.0.0 rev14
4
0. Revision History
Version Date Section Description
V1.0.0 Sep. 1, 2013 - Initial version
V1.0.1 Sep. 25, 2013 7 Added note (*1) to XMV "InputSelect" parameter
7 Added *2 to XMV "ATT" and "DigitalATT"
8 Separated Meter List of EXi8 and EXo8
V1.0.2 Jan.14, 2014 3.1 Added Heart beat command
3.1 Added explanation for escape character
3.2.4 Added note for "1-10) Time synchronization notication <Old format>"
3.2.4, 3.4.3 Added time set and get commands
3.2.4, 3.4.3 Added DST related commands
3.3.1 Added note for "2-1) Device run mode query"
3.3.3 Modied description text and added note for "2-9) Keepalive activation setting"
3.4.3 Added alert event log related commands
4 Fixed text "devstatus devmode" to "devstatus runmode" in communication start process explanation
4 Fixed communication start process ow diagram
6 Added parameter value detail for MY4-AEC (table 12, 13, 14)
7 Added parameter "MYInsert 16 Channel" to Parameter List
7 Added MY4-AEC parameters to Parameter List
7 Amend description for parameter "Power" in XMV Parameter List
8 Added MY4-AEC address to Meter List
V1.0.3 May 23, 2014 3.3.1, 4 Added clarication of [devstatus runmode] command, which is necessary to establish remote control
communication.
V1.3.0 Nov. 1, 2014 1.3.1, 1.3.2 Increased total number of remote controller devices which can simultaneously access the MTX
system.
3.1 Fixed some incorrect values in the "Normalized Value" column of the table, and in the note below the
table.
3.3.5 Added "setr" command, which allows relative inc/dec level control.
6 Added "value to data" tables for fader parameters.
7 Added comments in remarks column for when "setr" command is available.
7 Added "DigitalInputSensitivity" parameter for XMV
V2.0.3 Aug. 25, 2015 1, 3.2.2, 3.3.4
3.3.5, 3.3.6, 6.
7, 8
Added MRX7-D
1.3.3 Added "MRX7-D and Remote Control Setup List"
2, 3.2.3. Added "NOTIFY ssrecall" command
2, 3.2.4. Added "NOTIFY sscurrent_ex"command
2, 3.2.4. Added "NOTIFY ssrecall_ex" command
2, 3.3.8. Added "ssrecall_ex"command
3.1. Amended raw value examples for 400Hz and 2kHz
3.2.2. 1-5)
3.3.4. 2-10)
3.3.4. 2-11)
3.3.5 2-13)
3.3.5 2-14)
3.3.5 2-15)
Amended "Detail"
6 Fixed MTX5 parameter in "1.Input Patch"
7 Fixed Category of "INPUT CHANNEL"
7 Amended to clarify Analog Gain to "Gain"and Digital Gain to "D.Gain"
7 Fixed "Xpos" in "MATRIX"
7 Fixed "UniqueId" in "OUTPUT CHANNEL" of "SPEAKER PROCESSOR"
7 Fixed "Xpos" in "OUTPUT PORT" of "OUTPUT PORT"
7 Amended "Remarks" in "MY4-AEC"
V2.1.0 Dec. 22, 2015 3.2.2 Added new 'Important' comment regarding Parameter change notication raw/normalised values in
MRX7-D part
7 Fixed Remark for "Channel Name" parameter in MTX3/MTX5-D part
7 Fixed ElmNo for "ROUTER" parameter in MTX3/MTX5-D part
7 Fixed "INPUT CHANNEL LEVEL" & "INPUT CHANNEL MUTE" parameters in MTX3/MTX5-D part
7 Fixed "INPUT CHANNEL DCA" parameters in MTX3/MTX5-D part
7 Fixed "MATRIX OUTPUT MASTER" parameters in MTX3/MTX5-D part
7 Added "ZONE DCA/MUTE" parameters in MTX3/MTX5-D part
7 Fixed Remark for "EQ/GEQ Gain" parameter in MRX7-D
7 Added "Acoustic Echo Canceller" parameters in MRX7-D
7 Added "Revolabs Control" parameters in MRX7-D
7 Fixed Remark for "ChannelName" parameters in XMV series
8
Fixed Meter Name for "OUTPUT PORT OUTPUT(SLOT)" in MTX3/MTX5-D part
8 Fixed Meter Name for "Matrix Mixer" in MRX7-D part