User Guide

30 MU128 MIDI
1.2.16 Portamento Control
This message specifies the portamento source key number
(the key number at which portamento will begin).
Data of 0...127 specifies the portamento source key.
When Portamento Control is received, the currently-
sounding pitch will change at a Portamento Time of 0 to the
key of the next-received note-on of the same channel.
Control# Parameter Data Range
84 Portamento Control 0...127
(C-2...G8)
This is received even if Rcv PORTAMENTO = OFF.
1.2.17 Effect1 Depth(Reverb Send Level)
This message specifies the send level for the reverb effect.
Control# Parameter Data Range
91 Effect1 Depth 0...127
Increasing this value will produce a richer reverb. The effect
of the value will depend on the state of the reverb effect.
1.2.18 Effect3 Depth(Chorus Send Level)
This message specifies the send level for the chorus effect.
Control# Parameter Data Range
93 Effect3 Depth 0...127
Raising this value will increase the modulation or spacious-
ness. The effect of the value will depend on the state of the
chorus effect.
1.2.19 Effect4 Depth (Variation Effect Send
Level)
This message specifies the send level for the variation effect.
Control# Parameter Data Range
94 Effect4 Depth 0...127
However, this is not received if the Variation Effect
parameter Variation Connection = 0 (Insertion).
1.2.20 Data Increment/Decrement (for RPN)
This message increases or decreases the parameter value
specified for RPN (see 1.2.22), by increments of 1.
Control# Parameter Data Range
96 RPN Increment --
97 RPN Decrement --
The data byte is ignored.
1.2.21 NRPN (Non-registered parameter
number)
This message is used to specify a sound parameter (such as
vibrato, filter, EG, drum setup etc.) as an offset value.
Use NRPN MSB and NRPN LSB to specify the parameter
that you wish to modify, and then use Data Entry (see 1.2.4)
to set the value for the specified parameter.
MIDI data format
Control# Parameter Data Range
98 NRPN LSB 0...127
99 NRPN MSB 0...127
If the Multi Part parameter Rcv NRPN = OFF, that part will
not receive NRPN.
The following NRPN messages can be received.
NRPN Data Entry *1
MSB LSB MSB LSB
Parameter name and value range
01 08 mm -- *2 Vibrato rate
mm: 00 - 64 - 127
(-64...0...+63)
01 09 mm -- Vibrato depth
mm: 00 - 64 - 127
(-64...0...+63)
01 10 mm -- *3 Vibrato delay
mm: 00 - 64 - 127
(-64...0...+63)
01 32 mm --
Low pass filter cutoff frequency
mm: 00 - 64 - 127
(-64...0...+63)
01 33 mm -- Low pass filter resonance
mm : 00 - 64 - 127
(-64...0...+63)
01 36 mm -- High pass filter cutoff frequency
mm: 00 - 64 - 127
(-64...0...+63)
01 48 mm -- *4 EQ bass gain
mm: 00 - 64 - 127
(-64...0...+63)
01 49 mm -- *4 EQ treble gain
mm: 00 - 64 - 127
(-64...0...+63)
01 52 mm -- *4 EQ bass frequency
mm: 04 - 40
(32...2.0k [Hz])
01 53 mm -- *4 EQ treble frequency
mm: 28 - 58
(500...16.0k [Hz])
01 99 mm -- EG attack time
mm: 00 - 64 - 127
(-64...0...+63)
01 100 mm -- EG decay time
mm: 00 - 64 - 127
(-64...0...+63)
01 102 mm -- EG release time
mm: 00 - 64 - 127
(-64...0...+63)