User Manual
MU50 MIDI Data Format
13
2.1.4 XG Native Parameter Change
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n device Number
01001100 4C XG Model ID
0aaaaaaa aaaaaaa Address High
0aaaaaaa aaaaaaa Address Mid
0aaaaaaa aaaaaaa Address Low
0ddddddd ddddddd Data
||
11110111 F7 End of Exclusive
For parameters whose data size is 2 or 4, transmit the appropriate number of data bytes.
2.1.4.1 XG Sytem On
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1N device Number
01001100 4C XG Model ID
0aaaaaaa 00 Address High
0aaaaaaa 00 Address Mid
0aaaaaaa 7E Address Low
00000000 00 Data
11110111 F7 End of Exclusive
When On is received, the SOUND MODULE MODE will change to XG.
Since approximately 50 ms is required to execute this message, leave an appropriate
interval before
the message that follows it.
2.1.4.2 XG System Data parameter change
Refer to tables <1-1> and <1-2>.
2.1.4.3 System Information
Data transmission is performed in response to a Dump Request, but data reception is
ignored.
Refer to tables <1-1> and <1-3>.
2.1.4.4 Multi Effect1 Data parameter change
Refer to tables <1-1> and <1-4>.
2.1.4.5 Display Data parameter change
Refer to tables <1-1> and <1-5>.
2.1.4.6 Multi Part Data parameter change
Refer to tables <1-1> and <1-6>.
2.1.4.7 Drums Setup Data parameter change
Refer to tables <1-1> and <1-7>.
If a DRUM SETUP RESET parameter change is received while in XG mode, the Drum
Setup parameter values will be initialized.
In any mode, selecting a Drum Set will cause the Drum Setup parameter values to be
initialized.
2.1.5 MU80, MU50 native parameter change
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n device Number
01001001 49 MU80, MU50 Model ID
0aaaaaaa aaaaaaa Address High
0aaaaaaa aaaaaaa Address Mid
0aaaaaaa aaaaaaa Address Low
0ddddddd ddddddd Data
||
11110111 F7 End of Exclusive
For parameters with a data size of 2 or 4, transmit the appropriate number of data bytes.
2.1.5.1 MU80, MU50 System Data parameter change
Refer to tables <2-1> and <2-2>.
2.1.5.2 Current Performance parameter change
Refer to tables <2-1> and <2-3>.
2.1.5.3 Remote Switch
Refer to tables <2-1> and <2-4>.
2.1.6 Other parameter changes
2.1.6.1 Master Tuning
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0001nnnn 1n device Number
00100111 27 Model ID
00000001 30 Sub ID2
00000000 00
00000000 00
0mmmmmmm mm Master Tune MSB
0lllllll ll Master Tune LSB
0ccccccc cc
11110111 F7 End of Exclusive
This message simultaneously changes the pitch of all channels.
2.1.6.2 Disk Orchestra On
11110000 F0
01000011 43
01110011 73
00000001 01
00010100 14
11110111 F7
This message sets the SOUND MODULE MODE of this device to DOC MODE.
2.2 Bulk Dump
This device handles the following bulk dump data.
[ XG NATIVE ]
1) XG System Data
2) Multi Effect1 Data
3) Multi Part Data
4) Drums Setup Data
[ MU80, MU50 NATIVE ]
1) MU80, MU50 System data
2) Internal Performance
2.2.1 XG Native Bulk Dump
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0000nnnn 0n device Number
01001100 4C XG Model ID
0bbbbbbb bbbbbbb ByteCount
0bbbbbbb bbbbbbb ByteCount
0aaaaaaa aaaaaaa Address High
0aaaaaaa aaaaaaa Address Mid
0aaaaaaa aaaaaaa Address Low
00000000 00 Data
||
||
0ccccccc ccccccc Check-sum
11110111 F7 End of Exclusive
For the Address and Byte Count, refer to the supplementary tables.
The Check Sum is the value that results in a value of zero for the lower 7 bits when the
Start Address, Byte Count, and the Check Sum itself are added.
No more than 512 bytes shall be transmitted at one time. If one of the above Dump
Request messages for 513 bytes or more is received,
the data will be divided into appropriate packets of 512 bytes or less, and transmitted at
appropriate intervals (of at least 120 msec).
2.2.1.1 XG System Data bulk dump
Refer to tables <1-1> and <1-2>.
2.2.1.2 Multi Effect1 Data bulk dump
Refer to tables <1-1> and <1-4>.
2.2.1.3 Multi Part Data bulk dump
Refer to tables <1-1> and <1-6>.
2.2.1.4 Drums Setup Data bulk dump
Refer to tables <1-1> and <1-7>.