MW12CX/MW12C 使用说明书
注意事项 请在操作使用前,首先仔细阅读下述内容 * 请将本说明书存放在安全的地方,以便将来随时参阅。 警告 为了避免因触电、短路、损伤、火灾或其它危险可能导致的严重受伤甚至死亡,请务必遵守下列基本注意事 项。这些注意事项包括但不限于下列情况: 电源 / 电源线 关于潮湿的警告 • 只能使用本设备所规定的额定电压。所要求的电压被印在本设 备的铭牌上。 • 请勿让本设备淋雨或在水附近及潮湿环境中使用,或将盛有液 体的容器放在其上,否则可能会导致液体溅入任何开口。 • 只能使用提供的 AC 电源适配器 ( PA-20 或 YAMAHA 推荐的相应 产品)。 • 切勿用湿手插拔电源线插头。 • 请勿将电源线放在热源如加热器或散热器附近,不要过分弯折 或损伤电源线,不要在其上加压重物,不要将其放在可能被踩 踏引起绊倒或可能被碾压的地方。 当意识到任何异常情况时 • 若电源线出现磨损或损坏,使用设备过程中声音突然中断或因 此而发出异常气味或冒烟,请立即关闭电源开关,从电源插座 中拔出电源线插头,并请有资格的 YAMAHA 维修人员对设备进 行检修。 请勿打开 • 请勿打开本设备并试图拆卸其内部零件或进行
XLR 型插口应按下图所示进行布线 (IEC60268 标准 ): 针 1:地线,针 2:热线 (+) 和针 3:冷线 (-)。 TRS 耳机插口接线如下 : 套筒:地线,尖端:信号发送,环:返回。 对由于不正当使用或擅自改造本设备所造成的损失、数据丢失或破坏, YAMAHA 不负任何责任。 当不使用本设备时,请务必关闭其电源。 即使电源开关被置于 “STANDBY”(待机)位置,设备中仍有微量的电流。当确定长时间不使用本设备时,请务必将 AC 电源插头从 AC 电源插座拔出。 经常动态接触的零部件,如开关、控制旋钮、接口等,随着时间的推移,其性能会逐渐下降。请让有资格的 YAMAHA 维修服务人员 为您更换有缺陷的零部件。 电源打开时, MW 调音台的温度可能上升 15 至 20°C。 这是正常的。请注意,当环境温度超过 30°C 时,面板温度可能会超过 50°C, 小心以免灼伤。 * 本使用说明书同时适用于 MW12CX 和 MW12C。两种型号的主要差别是, MW12CX 包含数字效果, MW12C 没有内部效果。 * 在本使用说明书中,术语 “MW 调音台”同时指 MW12CX 和 MW12C。需要
前言 感谢您购买 YAMAHA MW12CX/MW12C USB录音调音台。MW12CX/MW12C包括一个使用 USB接口用于音频数据传输的调音台,以及用于 Windows® 和Macintosh® 计算机操作系统的 Cubase AI 4 DAW (数字音频工作站)。使用MW12CX/MW12C USB录音调音台和个人计算 机,您就可将一些基本元件组合成一个易于设置和操作的高性能计算机录音系统。 为了最大限度地发挥本调音台的超强功能和延长正常使用寿命,在使用之前请务必仔细阅读本 使用说明书。 阅读后,请将本说明书存放在安全的地方。 功能 通过单根 USB缆线连接到计算机 (第7页) MW调音台通过附带的 USB缆线连接到计算机。 立体声音频 数据通过 USB连接 (44.
前言 使用调音台前的准备 1 计算机系统要求 请务必将调音台电源开关置于 STANDBY位置。 小心 2 只能使用附带的电源适配器 (PA-20)或 YAMAHA 推 荐的 相应 产品。 使 用其 他适 配器 可能 会 导致 设备 损 坏、过热或火灾。 请将电源适配器连接到调音台背面的 AC ADAPTOR IN 连 接插 口 (q)中,然后 顺时针 拧紧 固定环 (w )将 连接固定。 w 3 q 将电源适配器插入到标准家用电源插座。 • 当不使用 调音台或本 地区正在发 生雷雨闪电 时,请 务必将电源适配器从电源插座拔出。 小心 Windows Vista 计算机 使用内置 USB接口的 Windows计算机 操作系统 Windows Vista CPU 1 GHz或更高主频的 Intel酷睿 /奔腾 /赛扬处理器 内存 1 GB或更多内存 Windows XP 计算机 使用内置 USB接口的 Windows计算机 操作系统 Windows XP Professional/XP Home Edition CPU 750 MHz或更高主频的 Intel酷睿
调音台基本操作 速成指南 调音台基本操作 本安装和操作的速成指南包括从安装 Cubase AI 4 软件到使用 Cubase AI 4 进行录音和混音。 浏览本部 分时可能需要参见第 16页的 “前面板和后面板”部分以及 Cubase AI 4软件附带的pdf手册。 步骤 1 安装 Cubase AI 4 重要事项! 1 2 3 由于安装 “DAW”软件时显示在计算机屏幕上的最终用户软件许可协议 ( EUSLA )已被替换为本 说明书后面的协议,所以应忽略 EUSLA 。请仔细阅读本说明书后面的软件许可协议,并同意该协议 以安装本软件。 启动计算机并登录到管理员帐户。 将附带的DVD光盘插入计算机的 DVD光驱。 打开 “Cubase AI 4 for Windows”文件夹,双击 “CubaseAI4.
调音台基本操作 速成指南 3 连接话筒和/或乐器。 步骤 有关如何进行连接的详细信息,请参见第 15页的 “设置”一节和第 16页的 “前面板和后面板”一 节。 3 打开系统 为了防止产生大的 “砰砰”声和噪音,请按照首先打 开声源 (乐器、 CD播放器等)最后打开功率放大器 或有源音箱的顺序打开音频设备的电源。 例子: 首先打开乐器、话筒和CD播放器,然后为调音台,最后打 开功率放大器或有源音箱。 打开幻相供电时请遵守下列注意事项。 使用幻相供电电容式话筒时,请 务必打开 MW 调音台PHANTOM 开关。 • 不需要幻相供电时请务必关闭PHANTOM 开关。 小心 • 打开此开关时,请务必只将电容话筒连接到XLR输入插 口。如果连接到幻相供电时,其他设备可能会损坏。但 此注意事项不适用于平衡式动圈话筒,因为它们不受幻 相供电的影响。 • 为了最大 降低音箱 损坏的可能 性,只有在关 闭功率放 大 器或有源 音箱时,才进行 打开幻相 供电的操作。 也可 以 将调音台的 输出控制旋钮 ( STEREO OUT 主衰减器 和 REC OUT衰减器)调到最低。 DI USB缆线 尽管电吉他
调音台基本操作 速成指南 步骤 4 调节电平和音调 电平调节 音调调节 1 第一步是恰当设定所有乐器和其它声源上的电 平控制旋钮。 2 调节通道的GAIN控制旋钮,让相应的 PEAK指 示灯在最高峰值电平时短暂地闪烁。 (立体声 通道9/10和 11/12未设置 GAIN控制旋钮。) 3 4 5 6 打开要录音的输入通道的 ON和 REC开关。 请确定PFL开关已关闭 ( ),并且 MONITOR开关设定为 REC ( )。 将REC OUT衰减器调高到 “ 0”位置。 通过耳机或监听音箱进行监听时,设定需要的 通道衰减器初始平衡。整体的耳机电平用 PHONES控制旋钮调节。 MONITOR开关 MW调音台的压缩器和三频段均衡器可用来调整单独通道的 音调以取得最佳混音效果。 为话筒输入使用高通滤波器 正如其名称,“高通滤波器”可只让超过特定频率的信号通 过。 反之,“截止频率”以下的信号将被削弱。打开MW高通 滤波器时, 80 Hz以下的信号将被削除。 这对降低人声演唱中 的低频呼吸噪音,以及处理通过话筒支架传递的噪音或隆隆 声非常有用。 对于话筒通道通常应该打开高通滤波器。 压缩
调音台基本操作 速成指南 步骤 5 使用 Cubase AI 4录音 本部分对使用安装的 Cubase AI 4软件在 MW调音台中录音的步骤进行了说明。 注 有关Cubase AI 4软件操作的详细信息,请参见软件中附带的 pdf格式手册。 Cubase AI 4设置 1 启动Cubase AI 4。 Windows: 单击[ 开始] → [所有程序 ] → [Steinberg Cubase AI 4] → [Cubase AI 4]启动程序。如果出现 ASIO Multimedia对话窗口,请单击 [Yes]。 Macintosh: 从左侧窗口中选择[Device]字段中的 [VST Audio System]。从右侧窗口中选择 [ASIO Driver]字段中的 [USB Audio CODEC (2)],然后单击 [OK]。直接跳到 步骤6,如下操作。 Macintosh: 双击[ 应用程序] → [Cubase AI 4]。 注 注 • 安装 Cubase AI 4 软件时如果指定了某个文件目 的地,必须从该位置启动应用程序。 • 在桌面上创建一个 Cubase AI 4快捷
调音台基本操作 速成指南 4 将显示 ASIO Direct Sound Full Duplex Setup 对话框。 只选择输入端口和输出端口 [USB Audio CODEC]复选框。 6 从 [File]菜单中选择 [New Project]创建一个新 项目文件。 将打开New Project对话窗口。 在本例中,选择 [CAI4 4 Stereo 8 Mono Audio Track Recorder]并单击 [OK]。 注 5 录制的Cubase AI 4 数据作为 “project file”存 储。 确认“ USB Audio CODEC 1/2”显示在 [Port System Name]字段中,并选择 Device Setup 窗口中的[Visible]列。 单击 [OK]关闭窗口。 注 如果[Port System Name]字段没有发生变化, 请关闭并重新启动Cubase AI 4,然后打开 Device Setup窗口。 7 出现目录选择对话窗口时,选择要保存项目的 项目和音频文件的文件夹,然后单击 [OK]。 将出现一个具有4个立体声音轨和 8个单声道音轨的 新项
调音台基本操作 速成指南 4 准备录音 1 单击音轨列表 (显示音轨名称的区域)选择 进行录音的音轨。 选定音轨的各种设置可从屏幕左侧的 Inspector窗口 选择。 [Record Enable]按钮 演奏要录音的乐器,调节MW调音台的 GAIN控 制旋钮、通道衰减器和 REC OUT衰减器,使 削波指示灯不亮。 <传送面板 > 削波指示灯 音轨列表 5 在项目窗口顶部的标尺指定想要开始录音的 点。 单击标尺的黑色区域将项目光标 (垂直黑线)移动 到该位置。 标尺 录音和播放 监察窗 1 输入路由 注 2 3 请确认要录制音轨的 [Record Enable]按钮已 打开。 录音开始时,项目光标将开始移动到右侧,并将创 建显示录音结果的框。 <传送面板 > 录制合成器时通常可以使用立体声音轨,录制 人声或吉他时通常可以使用单声道音轨。 单击监察窗中的输入路由字段,选择音频输入 源。立体声音轨选择 “Stereo In 1”,单声道 音轨选择 “Left (Right)-Stereo In 1”。 单击传送面板的[Record]按钮开始录音。 Record (录音)
调音台基本操作 速成指南 4 若要收听刚刚录音的音轨,或者使用传送面板 [Rewind] 按钮或者标尺倒转到录音部分的开 始,然后单击传送面板的 [Start]按钮。 整体播放电平将通过调音台右侧窗口的主部分母线 电平表显示,通道电平将通过通道条电平表显示。 注 • 单击调音台窗口左上角的 [Narrow/Wide] 按钮增 大调音台通道条的宽度。 • Cubase AI 4 的输出信号被路由发送至 MW 调音 台 的 2TR IN 输入 插口。 若要用 插在 MW 调音 台 上的耳机收听播放的声音,请将母线选择开关设 定为 TO MONITOR( ),用2TR IN/USB控制 旋钮和 PHONES控制旋钮调节音量。 [Narrow/Wide]按钮 若要保存项目文件,在实际保存文件前从 [File]菜单中选择 [Save]并输入文件名称。 经常保存项目文件,防止发生问题时造成大量数据 丢失。 6 7 重复步骤1到 5在相同音轨上录制其它内容。 若要在不同音轨上录制其它内容,请选择一个 新音轨并重复录音步骤。 注 在录音时可以同时监控正在录制的声音和以前 录制的声音 (MONITOR MIX)
调音台基本操作 速成指南 4 左右拖动通道条上方的声像控制旋钮,设定每 个音轨的立体声位置。 6 对混音已做出最终调节后,请进入 [File] 菜 单并选择[Export] → [Audio Mixdown]。 7 输入文件名并选择保存文件的目标以及文 件类型。 如果要使用文件创建一张音频 CD,请选择 WAV文 件类型 (Macintosh OS X操作系统中的 AIFF)、 Stereo Out (立体声)、 16位和 44.
参考指南 设置 参考指南 吉他 有源音箱 合成器 脚踏开关 (YAMAHA FC5) 贝司 录音机 CD播放器 话筒 DI 效果处理器 (激励器) 效果处理器 耳机 有源监听音箱 有源监听音箱 个人计算机 MW12CX MW12CX/MW12C 使用说明书 15
参考指南 前面板和后面板 以下说明同时适用于 MW12CX和MW12C。需要说明每种型号的不同功能时,先说明MW12CX的功能, 然后在后面的括号中说明 MW12C的功能: MW12CX ( MW12C)。 通道控制部分 1 MIC输入插口 (通道1-4、 5/6、 7/8) 通道 1~ 4 (单声道) 通道 5/6和 7/8 (立体声) 通道 9/10和 11/12 (立体声) 这些是平衡式 XLR型话筒输入插口 (1:地线; 2: 热 线; 3:冷线)。 2 LINE输入插口 (通道 1-4) 1 1 这些是平衡式 TRS耳机插口型线性输入插口 (T:热线; R:冷线;S:地线)。 可以将平衡式或非平衡式耳机插头插入这些插口。 4 3 LINE输入插口 (通道 5/6-11/12) 2 3 这些是非平衡式耳机插口型立体声线性输入插口。 3 4 LINE输入插口 (通道 9/10、 11/12) 5 这些是非平衡式立体声 RCA针式插口。 注 6 6 7 7 5 INSERT插口 (通道1-4) 每个这类插口都在相应单声道输入通道 (通道 1-4)的均 衡器与衰减器
参考指南 前面板和后面板 6 GAIN控制旋钮 B AUX PRE开关 调节输入信号电平。 为 了 获得 信噪 比和 动态 范 围的 最佳 平衡,调 节 电平 使 PEAK 指示灯 (9)仅在最高输入瞬间峰值时偶尔短暂 地亮起。 -60~ -16 刻度为 MIC 输入的调节范围。-34 ~ +10 刻度为 LINE输入的调节范围。 7 C EFFECT (AUX2)控制旋钮 开关 (高通滤波器) 此开关使 HPF 打开或关闭。要打开 HPF,请按下此开关 ( )。HPF将削去 80 Hz以下的频率(HPF 不适用于立 体声输入通道 3 的线性输入)。 8 COMP控制旋钮 调节 应用到通道的压缩电平 值。将旋钮向右旋转 时,压 缩率 将增大,同时相应地自动 调节输出增益。将获 得一 个 更平滑的、甚至是动态的 效果,这是由于整体电 平增 强后高声信号变低所致。 避免将压缩率 设得太高,因为由此 引起的较高平 均输 出电平会产生反馈。 注 选择是否将前置衰减器或后置衰减器的信号发送到 AUX (AUX1)母线。如果将此开关设定为开 ( ) ,调音 台将前置衰减器信号 (通道衰减器 I前的信号)
参考指南 前面板和后面板 主控制部分 1 2TR IN插口 这些 RCA 针式插口可用来输入立体声声源。 希望将 CD 播放器直接连接到调音台时,可使用这些插口。 • 选择希望用 2TR IN/USB开关 E 发送信号的位置,并 注 2 1 用 主控 制部 分的 2TR IN/USB 控制 旋钮 调节 信号 电 平。 6 • 2TR IN 和 USB 两个输入插口的输入信号将混合在一 起。 4 2 REC OUT 1 (L、 R)插口 7 这些是 RCA针式插口,可以用来连接外接立体声录音 机。经 REC OUT衰减器处理的信号从这些插口输出。 3 REC OUT 2 (L、 R)插口 5 3 8 这些是阻抗平衡式 TRS耳机插口,可以用来连接外接立 体声录音机。 经REC OUT衰减器处理的信号从这些插 口输出。 4 RETURN L (MONO)、 R插口 B 9 这些是非平衡式耳机插口型线性输入插口。 这些插口接 收的信号被发送到 STEREO L/R母线及 AUX (AUX1) 母线。这些插口一般用来接收从外接效果设备 (混响、 延迟等)返回的信号。 注 0 C 这些
参考指南 前面板和后面板 D MONITOR/PHONES 8 PHONES插口 将一对耳机连接此 TRS 耳机插孔。PHONES 插口输出的 信号与 MONITOR OUT插口相同。 • MONITOR开关 如果将此开关设定为 REC ( ), REC L/R母线信号将 被发送到 MONITOR OUT插口、PHONES插口和电平表。 如果设定为 STEREO( ),STEREO L/R母线信号将被 发送到这些插口和电平表。 9 PHANTOM +48 V电源开关 用 此开关可打开或关闭 幻相电源。打开此开关时,调 音 台将向所有提供 XLR 话筒输入插口的通道 (通道 1-4、 5/6、 7/8)提供+48V幻相电源。 使用 一个或几个以幻相电 源为电源的电容话筒时,请 打 开此开关。 注 打开此开关时,调音台将向所有 XLR型 MIC INPUT插口 的针2和针 3提供 DC +48 V电源。 • 如果您不需要幻相电源,务必关闭此开关 ( 小心 )。 • MONITOR控制旋钮 控制输出到 MONITOR OUT插口的信号电平。 • PHONES控制旋钮 控制输出到 PHONES插口的
参考指南 前面板和后面板 数字效果 * 只有 MW12CX有数字效果。 1 FOOT SWITCH插口 可以将 YAMAHA FC5脚踏开关 (另售)连接到此插口,用它来打开或关闭 数字效果。 1 2 PROGRAM数据盘 2 从 16种内部效果中选择一种。有关内部效果的详细信息,请参见第 21页。 3 PARAMETER控制旋钮 3 调节所选效果的参数 (深度、速度等)。 每种效果类型最后使用的参数值将会被保存。 4 注 当您变换 到不同的效果类型时,对于新选 择的效果,调音台将自动恢复 以前 使用的参数值 (无论 PARAMETER控制旋钮目前处在什么位置)。 电源关闭时,这些参数值将被复位。 4 AUX 控制旋钮 调节从内部数字效果单元发送到 AUX母线的信号电平。 注 EFFECT RTN衰减器不影响发送到 AUX母线的信号电平。 5 ON 开关 打开或关闭内部效果。只有打开此开关,才能应用内部效果。打开时开关亮 橙灯。 可以用选购的 YAMAHA FC5脚踏开关 (另售)打开或关闭数字效果。 5 6 注 电源打开时的默认状态为, ON 开关亮灯,内部效果单元被激活
参考指南 前面板和后面板 数字效果程序一览表 编号 程序 参数 说明 1 REVERB HALL 1 REVERB TIME 2 REVERB HALL 2 REVERB TIME 3 REVERB ROOM 1 REVERB TIME 4 REVERB ROOM 2 REVERB TIME 5 REVERB STAGE 1 REVERB TIME 6 REVERB STAGE 2 REVERB TIME 7 REVERB PLATE REVERB TIME 模拟金属板混响单元,以产生更加强劲的声音。 8 DRUM AMBIENCE REVERB TIME 与使用低音鼓相同的短促混响。 9 KARAOKE ECHO DELAY TIME 用于卡拉 OK演唱 (跟唱)时的回声。 10 VOCAL ECHO DELAY TIME 适用于声乐的回声。 11 CHORUS 1 LFO 频率 12 CHORUS 2 LFO 频率 通过调制延时时间创建一种浑厚的声音。 用 PARAMETER控制旋钮可调节调制延时时间的 LFO* 频
参考指南 故障排除 MW调音台无法打开。 ❑ 附带的电源适配器是否已经正确插入调音台和适当的 AC壁装电源插座? 系统无法正确运行。 ❑ 是否已经正确连接了 USB缆线和所有必要的音频线缆? ❑ 是否使用了 USB集线器? USB集线器可能会干扰正常操作,因此试着将 MW调音台直接连接到计算机的 USB端口。如 果计算机有多个 USB端口,试着使用不同的 USB端口。 ❑ 是否同时使用了其它 USB设备? 如果使用了其它设备,试着将其它设备取下,只连接 YAMAHA USB设备。 无声音。 ❑ ❑ ❑ ❑ ❑ 音箱缆线连接是否正确,或者是否发生了短路? 所用通道的 ON开关、 ST开关和 REC开关是否已打开? 声源、音频设备、应用程序软件、计算机操作系统等的音量控制是否设定在适当的级别? 计算机操作系统的输出是否设定为静音? 是否同时运行了多个应用程序? 请务必退出所有没有正在使用的应用程序。 ❑ 计算机操作系统的声音输出指定是否正确? Windows: 1. 从[开始 ] 菜单中单击[控制面板 ],然后双击 “声音、语音和音频设备”图标打开 “声音和 音频设备”对话窗口。 2.
参考指南 故障排除 声音中断或失真。 ❑ PEAK指示灯是否闪烁红色? 可能必须调低 GAIN控制旋钮或通道衰减器电平以避免失真。 ❑ 应用效果和压缩器的电平是否适当? 可能需要调低 EFFECT RTN衰减器、 ETTECT控制旋钮和 COMP控制旋钮。 ❑ 使用的计算机是否符合列出的系统要求? 详情请参见第 6页的 “计算机系统要求”。 ❑ 是否同时运行了其它应用程序、设备驱动程序或 USB设备 (扫描仪、打印机等)? 请务必退出所有没有正在使用的应用程序。 ❑ 是否正在播放很多音轨? 可以 同时播放 的音轨数取 决于正在使 用的计算机 的性能。 如果超过 计算机性 能范围可能 会 造成播放中断。 ❑ 是否正在录制或播放长的连续音频? 计算机的音频数据处理能力取决于许多因素,其中包括 CPU速度和对外接设备的访问。 在 Windows计算机中,下述的一些设置更改可以提高性能。 1. 从 [ 开始 ] 菜单中单击 [ 控制面板 ],然后双击 “声音、语音和音频设备”图标打开 “声音 和音频设备”对话窗口。 2.
参考指南 规格 ■ 电气规格 STEREO OUT 频率响应 REC OUT2 EFFECT/AUX ( AUX1、 2*) SEND MONITOR OUT、 REC OUT1 STEREO OUT 总谐失真 (THD + N) CH INPUT 1-4 MIC 哼声和噪声 STEREO OUT 哼声和噪声是用 6dB/ 八 REC OUT2 度音阶滤波器在 EFFECT/AUX 12.7kHz下测量的,相 ( AUX1、 2*) SEND 当于具有无穷大 dB/ 八 度音阶衰减的 20kHz滤 STEREO OUT 波器。 REC OUT2 STEREO OUT 串音 (1 kHz) 最大电压增益 (1 kHz) GAIN: 最小值 (通道 1-7/8) 20 Hz-20 kHz 1 kHz 时的标称输出电平 输入:通道 1-11/12、 RETURN、 2TR IN 幻相电压 类型 最大 值 单位 -3.0 0.0 1.0 dB 0.
参考指南 规格 ■ 模拟输入规格 输入连接插口 CH INPUT MIC (通道1-4) CH INPUT LINE (通道1-4) ST CH MIC INPUT (通道5/6、 7/8) ST CH LINE INPUT (通道5/6、 7/8) 增益 输入阻抗 适当阻抗 3kΩ 50-600Ω 话筒 -60 dB -16 dB -34 dB 10kΩ 600Ω 线路 3kΩ 50-600Ω 话筒 +10 dB -60 dB -16 dB -34 dB 2TR IN (L、 R) 标称电平 -80 dBu (0.078 mV) -60 dBu (0.775 mV) 削波前的 最大值 -40 dBu (7.75 mV) -36 dBu (12.3 mV) -16 dBu (123 mV) +4 dBu (1.23 V) -54 dBu (1.55 mV) -34 dBu (15.5 mV) -14 dBu (155 mV) -10 dBu (245 mV) +10 dBu (2.45 V) +30 dBu (24.5 V) -80 dBu (0.
参考指南 规格 ■ 外形尺寸图 86.1 79.6 346.2 433.9 436.
MW12CX/MW12C 使用说明书 -60dBu -50dBu -40dBu -30dBu -20dBu -10dBu 0dBu +10dBu +20dBu +30dBu (CH5/6, 7/8) R L R CH IN MIC Gain:Max [-60dBu] CH IN LINE Gain:Max [-34dBu] CH IN MIC Gain:Min [-16dBu] CH IN LINE Gain:Min [+10dBu] FOOT SW EFFECT ON/OFF [-10dBV] [-7.
关于附带光盘 特别注意事项 关于附带的光盘中的 DAW 软件 • 附带光盘中包含的软件以及其版权归 Steinberg Media Technologies GmbH 独家所有。 附带光盘中包含可用于 Windows 和 Macintosh 计算机的 DAW 软件。 • 本软件和说明书的使用由授权协议支配,打开软件包裹封 条视为完全同意协议。 (安装应用程序前请仔细阅读本 说明书最后的软件授权协议。) 注 • 为了安装附带光盘中的软件,需要可以运行的Internet 连接。 确认在安装时填写所有需要的字段。 • 如果使用 Macintosh 计算机,请双击 “***.mpkg”文件开始 安装。 • 无制造商的书面许可严禁以任何方式复制软件或说明书之 整体或部分。 • YAMAHA 不承担有关软件及文件使用的责任或担保,对使 用本说明书及软件的后果不负责任。 • 禁止将本光盘用于音频 / 视频播放。请勿在音频 / 视频 CD / DVD 播放器上播放本光盘。否则可能损坏播放器,无法 修补。 • 有关最低系统要求和光盘中软件的最新信息,请单击下面 的网站。
4. 媒介的有限担保 6.
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 关于各产品的详细信息,请向就近的 YAMAHA 代理商或下列 经销商询问。 THE NETHERLANDS/ BELGIUM/LUXEMBOURG Yamaha Music Central Europe GmbH, Branch Benelux Clarissenhof 5-b, 4133 AB Vianen, The Netherlands Tel: 0347-358 040 FRANCE U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave.