User Manual

MX49 MX61 MX88 Data List
53
MIDI Data Format
Many MIDI messages listed in the MIDI Data Format section are expressed in hexadecimal
or binary numbers. Hexadecimal numbers may include the letter “H” as a suffix. The letter
“n” indicates a certain whole number.
The chart below lists the corresponding decimal number for each hexadecimal number.
Additional Notes
• For example, 144 – 159(Decimal)/9nH/1001 0000 – 1001 1111(Binary) indicate the note-
on messages for the channels 1 through 16 respectively. 176 – 191/BnH/1011 0000 –
1011 1111 indicate the control change messages for the channels 1 through 16
respectively. 192 – 207/CnH/1100 0000 – 1100 1111 indicate the program change
messages for the channels 1 through 16 respectively. 240/F0H/1111 0000 is positioned
at the beginning of data to indicate a system exclusive message. 247/F7H/1111 0111 is
positioned at the end of the system exclusive message.
• aaH (Hexadecimal)/0aaaaaaa (Binary) indicates the data addresses. The data address
consists of High, Mid and Low.
• bbH/0bbbbbbb indicates byte counts.
• ccH/0ccccccc indicates check sums.
• ddH/0ddddddd indicates data/value.
SYNTHESIZER/SEQUENCER PART
(1) TRANSMIT FLOW
MIDI <-+-[SW1]--+---------NOTE ON/OFF 9nH
OUT | |
| +---------KEY'S AFTER TOUCH AnH (Seq only)
| |
| +---------CONTROL CHANGE (All in Seq)
| | MODULATION BnH, 01H
| | VOLUME BnH, 07H
| | PAN BnH, 0AH
| | EG SUSTAIN LEVEL BnH, 1FH
| | SUSTAIN SWITCH BnH, 40H
| | FILTER RESONANCE BnH, 47H
| | EG RELEASE TIME BnH, 48H
| | EG ATTACK TIME BnH, 49H
| | FILTER CUTOFF FREQ BnH, 4AH
| | EG DECAY TIME BnH, 4BH
| | REVERB SEND BnH, 5BH
| | CHORUS SEND BnH, 5DH
| | ASSIGNABLE CONTROLLERS BnH, (00H .. 5FH)
| |
| +--[SW7]--BANK SEL MSB BnH, 00H
| | BANK SEL LSB BnH, 20H
| |
| +---------CHANNEL MODE MESSAGE (Seq only)
| | RESET ALL CONTROLLERS BnH, 79H
| | LOCAL CONTROL BnH, 7AH
| | OMNI MODE OFF BnH, 7CH
| | OMNI MODE ON BnH, 7DH
| | MONO MODE ON BnH, 7EH
| | POLY MODE ON BnH, 7FH
| |
| +--[SW8]--PROGRAM CHANGE CnH
| |
| +---------CHANNEL AFTER TOUCH DnH (Seq only)
| |
| +---------PITCH BEND CHANGE EnH
|
+--[SW3]-----------SYSTEM REALTIME MESSAGE
| TIMING CLOCK F8H
|
+--[SW4]-----------SYSTEM REALTIME MESSAGE
| START FAH
| CONTINUE FBH
| STOP FCH
|
+------------------ACTIVE SENSING FEH
|
+--[SW5]-+---------SYSTEM EXCLUSIVE MESSAGE (All in Seq)
| +---------<BULK DUMP>
| | F0H 43H 0nH 7FH 17H bhH blH ahH amH alH ddH....ddH ccH F7H
| |
| +---------<PARAMETER CHANGE>
| F0H 43H 1nH 7FH 17H ahH amH alH ddH.....ddH F7H
|
+------------------SYSTEM EXCLUSIVE MESSAGE
IDENTITY REPLY
F0H 7EH 7FH 06H 02H 43H 00H 41H 47H 06H 00H 00H 00H 7FH F7H
[SW1] MIDI Transmit Channel
The data is transmitted over the specified channel for the current Part.
However, Program Change messages for changing the Performance are transmitted over the Basic Channel.
[SW3] MIDI Clock Out
[SW4] Seq MIDI Control
[SW5] MIDI Device Number
When set to all, transmitted via 1.
[SW7] SYSTEM Bank Select Switch
[SW8] SYSTEM Program Change Switch
Decimal Hexadecimal Decimal Hexadecimal
0 0 64 40
1 1 65 41
2 2 66 42
3 3 67 43
4 4 68 44
5 5 69 45
6 6 70 46
7 7 71 47
8 8 72 48
9 9 73 49
10 0A 74 4A
11 0B 75 4B
12 0C 76 4C
13 0D 77 4D
14 0E 78 4E
15 0F 79 4F
16 10 80 50
17 11 81 51
18 12 82 52
19 13 83 53
20 14 84 54
21 15 85 55
22 16 86 56
23 17 87 57
24 18 88 58
25 19 89 59
26 1A 90 5A
27 1B 91 5B
28 1C 92 5C
29 1D 93 5D
30 1E 94 5E
31 1F 95 5F
32 20 96 60
33 21 97 61
34 22 98 62
35 23 99 63
36 24 100 64
37 25 101 65
38 26 102 66
39 27 103 67
40 28 104 68
41 29 105 69
42 2A 106 6A
43 2B 107 6B
44 2C 108 6C
45 2D 109 6D
46 2E 110 6E
47 2F 111 6F
48 30 112 70
49 31 113 71
50 32 114 72
51 33 115 73
52 34 116 74
53 35 117 75
54 36 118 76
55 37 119 77
56 38 120 78
57 39 121 79
58 3A 122 7A
59 3B 123 7B
60 3C 124 7C
61 3D 125 7D
62 3E 126 7E
63 3F 127 7F