ENGLISH FRANÇAIS AMP CONTROL UNIT DEUTSCH NETWORK HUB and BRIDGE ESPAÑOL Owner’s Manual Mode d’emploi Bedienungsanleitung Manual de instrucciones NETWORK HUB AND BRIDGE LINK LOCK CONDUCT ERROR 88 M
ACU16-C/NHB32-C Owner’s Manual Addendum Please make the following changes and additions to the ACU16-C/NHB32-C owner’s manual. Some of these are due to the ACU16-C/NHB32-C system software upgrade, while others are corrections and supplementary explanations. Changes due to the software upgrade ❏ Support for CobraNet “Low Latency” (system software v1.10) In conjunction with the upgrade to system software V1.10, the latency setting that had been fixed at 5.33 ms can now be selected from three choices (5.
Incorrect—To view the Network Amp Manager Owner’s Manual, you’ll need to install the Adobe Acrobat Reader software, which is included on the CD-ROM. If you already have this software installed, skip this section. Correct—To view the NetworkAmp Manager Owner’s Manual (PDF format), Adobe Reader software (free of charge) must be installed. If you don’t have Adobe Reader, please download it from the Adobe Corporation’s website. http://www.adobe.
ACU NHB Pera_M_A Page 1 Wednesday, April 23, 2003 4:38 PM / Notes on rack-mounting the unit If you install the ACU16-C/NHB32-C along with another ACU16-C/NHB32-C or other device in a rack that is not well ventilated, the temperature inside the rack may rise due to the heat generated from the devices and the devices may be unable to perform properly. When you rack-mount the unit, be sure to keep a gap of 1U (4.5cm) above and below the unit for better ventilation.
ACU NHB Pera_M_A Page 1 Wednesday, April 23, 2003 10:04 AM / Important Note for PC-N Series Power Amplifier Users When you are using the ACU16-C connected to a PC9500N or PC4800N power amplifier, the NetworkAmp Manager's meter may not display the correct value, depending on your power amplifier.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
Explanation of Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
4 Software Licensing Agreement The following is a legal agreement between you, the end user, and Yamaha Corporation (“Yamaha”). The enclosed Yamaha software program is licensed by Yamaha to the original purchaser for use only on the terms set forth herein. Please read this licensing agreement with care. Opening this package indicates that you accept all terms outlined herein. If you do not agree to the terms, return this package unopened to Yamaha for a full refund.
5 ENGLISH Precautions Warnings Installation • • • • Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Manual or as marked on the unit. Failure to do so is a fire and electrical shock hazard. Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock may result. Do not place heavy objects, including this unit, on top of the power cord. A damaged power cord is a fire and electrical shock hazard.
6 Cautions Installation • • • • • • • • Keep this unit away from the following locations: — Locations exposed to oil splashes or steam, such as near cooking stoves, humidifiers, etc. — Unstable surfaces, such as a wobbly table or slope. — Locations exposed to excessive heat, such as inside a car with all the windows closed, or places that receive direct sunlight. — Locations subject to excessive humidity or dust accumulation. Hold the power cord plug when disconnecting it from an AC outlet.
Important Information Operating Notes • • • • • The performance of components with moving contacts, such switches, rotary controls, faders, and connectors, deteriorates over time. The rate of deterioration depends on the operating environment and is unavoidable. Consult your dealer about replacing defective components. Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone away from the unit.
8 Trademarks Adobe, Acrobat, and Reader are registered trademarks of Adobe Systems Incorporated. CobraNet and Peak Audio are trademarks of Cirrus Logic, Inc. Ethernet is a trademark of Xerox Corporation. Intel and Pentium are registered trademarks of Intel Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation, Inc. Yamaha is a trademark of Yamaha Corporation. All other trademarks are the property of their respective holders and are hereby acknowledged.
Contents 1 NetworkAmp Manager Installation . . . . . . . . . . . 10 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CD-ROM Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ACU16-C/NHB32-C Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 NetworkAmp Manager Installation 1 NetworkAmp Manager Installation Introduction This chapter explains how to install NetworkAmp Manager and the necessary drivers. For information on how to use NetworkAmp Manager, refer to the Network Amp Manager Owner’s Manual, which is included on the CD-ROM in PDF format and can be opened directly from NetworkAmp Manager’s Help menu.
ACU16-C/NHB32-C Hookup 11 The following illustration shows the hookup methods that can be used to connect the ACU16-C/NHB32-C to your computer: USB or serial. 1. USB NETWORK HUB AND BRIDGE LINK NHB32-C LOCK CONDUCT 88 ERROR ACU16-C USB port USB port USB cable 2. Serial - NHB32-C Windows PC running NetworkAmp Manager ACU16-C TO COMPUTER port Serial cable (9-pin D-sub) Serial port (RS-232C) Note: Before you connect to serial ports, turn off the ACU16-C/NHB32-C and your computer.
12 NetworkAmp Manager Installation Installing Acrobat Reader 1 To view the Network Amp Manager Owner’s Manual, you’ll need to install the Adobe Acrobat Reader software, which is included on the CD-ROM. If you already have this software installed, skip this section. Start your computer and Windows, and insert the included CD-ROM into your computer’s CD-ROM drive. 2 On the CD-ROM, double-click the “Acroread_” folder. This folder contains Acrobat software in several languages.
Installing the USB MIDI Driver 13 1 Start your computer and Windows, and insert the included CD-ROM into your computer’s CD-ROM drive. 2 Turn off the ACU16-C/NHB32-C and use a USB cable to connect the USB port on the ACU16-C/NHB32-C to a USB port on your computer. 3 Turn on the ACU16-C/NHB32-C. The Add New Hardware Wizard appears. If it doesn’t appear, try disconnecting and reconnecting the USB cable. Alternatively, open the Add New Hardware control panel. 4 Click Next.
14 NetworkAmp Manager Installation 5 Select “Search for the best driver for your device (Recommended),” and then click Next. The following window appears. 6 Select “Specify a location,” and specify “D:\USBdrv_” (replacing “D” with the drive letter of your CD-ROM drive), and then click Next. When the driver is located, “YAMAHA USB MIDI Driver” is displayed, as shown below. 7 Click Next. Note: You may be prompted to insert your Windows CD-ROM.
Installing the USB MIDI Driver 15 1 Start your computer and Windows, and insert the included CD-ROM into your computer’s CD-ROM drive. 2 Turn off the ACU16-C/NHB32-C and use a USB cable to connect the USB port on the ACU16-C/NHB32-C to a USB port on your computer. 3 Turn on the ACU16-C/NHB32-C. The Add New Hardware Wizard appears. If it doesn’t appear, try disconnecting and reconnecting the USB cable. Alternatively, open the Add New Hardware control panel.
16 NetworkAmp Manager Installation Windows 2000 1 Start your computer and Windows, log on as the Administrator, and then insert the included CD-ROM into your computer’s CD-ROM drive. 2 Go to My Computer–>Control Panel–>System–>Hardware–>Driver Signing–>File Signature Verification, select “Ignore—Install all files, regardless of file signature,” and then click OK. 3 Turn off the ACU16-C/NHB32-C and use a USB cable to connect the USB port on the ACU16-C/NHB32-C to a USB port on your computer.
Installing the USB MIDI Driver 17 1 Start your computer and Windows, and insert the included CD-ROM into your computer’s CD-ROM drive. 2 Click the Start button, and then click Control Panel. If the Control Panel window appears as shown below, click “Switch to Classic View” on the left side of the window in order to see all the control panels. 3 Go to System Hardware–>Driver signatures–>Driver signature options, select “Ignore—Install software without asking for confirmation,” and then click OK.
18 NetworkAmp Manager Installation Installing the Yamaha CBX Driver If you are connecting the ACU16-C/NHB32-C to a serial port on your computer, you’ll need to install the Yamaha CBX driver. If you already have this software installed, skip this section. Computer NetworkAmp Manager Serial cable Yamaha CBX driver ACU16-C/NHB32-C 1 Double-click the “Mididrv_” folder on the CD-ROM. 2 Double-click “Setup.exe.” 3 Follow the on-screen instructions to install the software.
• • • • • • 19 If for some reason installation of the Yamaha USB Driver fails, the ACU16-C/NHB32-C may be registered as an unknown device and you may not be able to reinstall the driver until the unknown device is deleted. In this case, open the System control panel, click the Device Manager tab, and select the “View devices by connection” option. If an item called “Other devices” appears in the list, click it. If there’s an item called “Unknown device,” select it and then click the Remove button.
20 ACU16-C Amp Control Unit 2 ACU16-C Amp Control Unit Introduction The Yamaha ACU16-C Amp Control Unit is a CobraNet interface offering 24-bit D/A conversion of up to 16 CobraNet audio channels, which are output via Euro-block connectors for connection to up to eight 2-channel power amplifiers. Up to 16 ACU16-Cs can be used on a single CobraNet network, providing D/A conversion of up to 256 CobraNet audio channels.
21 Front Panel ENGLISH Front Panel 1 2 3 4 A USB port This USB port is used to connect the ACU16-C to a USB port on a PC running NetworkAmp Manager. The rear panel TO COMPUTER port offers an alternative method of connection. The PC port to be used for communication with the ACU16-C is set in NetworkAmp Manager. B UNIT ID switch This switch is used to set the unit ID of the ACU16-C. Each ACU16-C on the network must be assigned an exclusive ID from 0 to 15.
22 ACU16-C Amp Control Unit Rear Panel 1 2 3 4 5 6 A Grounding screw For electrical safety reasons, it’s important that the ACU16-C is grounded properly. The supplied power cord has a three-pin plug, and if the ground terminal of the AC outlet is grounded, then the unit will be grounded sufficiently through the power cord. If the AC outlet does not provide a suitable ground, this screw must be connected to a good ground point.
Specifications 23 D/A converters 24-bit, 128-times oversampling Dynamic range1 110 dB typical Frequency response 20 Hz–20 kHz +0.5, –1.5 dB (nominal output level @ 1 kHz) Crosstalk –80 dB (@ 1 kHz, between adjacent channels) Signal delay 0.625 ms (CobraNet to analog output) Total harmonic distortion (20 Hz–20 kHz) Hum & +4 dB output Less than 0.05% Full scale output Less than 0.01% noise1 –92 dB PRIMARY/SECONDARY connectors RJ-45 x2 (16 in), transformer isolated, IEEE 802.
24 ACU16-C Amp Control Unit 395.8 17.5 322 D:385.5 378 0.65 44 W:480 H:44.65 7.5 349.3 30 430 10.2 Dimensions Units: mm Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corporation reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment, or options may not be the same in every locale, please check with your Yamaha dealer.
25 3 NHB32-C Network Hub & Bridge Introduction The Yamaha NHB32-C Network Hub & Bridge is a CobraNet bridge offering flexible patching of up to 64 CobraNet audio channels (32 in/32 out) to 64 AES/EBU format inputs and outputs (32 in/32 out). Up to 99 patch setups can be created, stored, and recalled in NetworkAmp Manager. Patches can be recalled directly from the NHB32-C’s front panel while NetworkAmp Manager is offline.
26 NHB32-C Network Hub & Bridge Front Panel NETWORK HUB AND BRIDGE LINK LOCK CONDUCT 88 ERROR 1 2 3 4 5 6 7 89 J K A USB port This USB port is used to connect the NHB32-C to a USB port on a PC running NetworkAmp Manager. The rear panel TO COMPUTER port offers an alternative method of connection. The PC port to be used for communication with the NHB32-C is set in NetworkAmp Manager. B UNIT ID switch This switch is used to set the unit ID of the NHB32-C.
Front Panel 27 This button is used to set the wordclock source, which can be a pair of AES/EBU inputs, the CobraNet network, or the NHB32-C’s BNC WORD CLOCK IN connector. To set the wordclock source, use the button to select a source and while the corresponding wordclock indicator is flashing, press the button again. The wordclock source will change and the corresponding indicator will stop flashing and light up continuously.
28 NHB32-C Network Hub & Bridge Rear Panel - 1 2 3 4 5 6 78 9 J A Grounding screw For electrical safety reasons, it’s important that the NHB32-C is grounded properly. The supplied power cord has a three-pin plug, and if the ground terminal of the AC outlet is grounded, then the unit will be grounded sufficiently through the power cord. If the AC outlet does not provide a suitable ground, this screw must be connected to a good ground point.
Rear Panel 29 This 9-pin male D-sub port is used to connect a Yamaha AD824 A/D converter. Control signals from a supporting device, such as the Yamaha DME32 Digital Mixing Engine or Yamaha DM2000 Digital Production Console, can be transmitted via CobraNet’s Serial Bridge. The COM port is an RS-422 serial interface, supporting cable runs of up to 1 kilometer. I TO COMPUTER port This 9-pin male D-sub port is used to connect the NHB32-C to a COM port on a PC running NetworkAmp Manager.
30 NHB32-C Network Hub & Bridge Specifications Memories 100 (#0 is read-only) Indicator 7-segment LED x2 PRIMARY/SECONDARY connectors RJ-45 x2 (32 in/32 out), transformer isolated, IEEE 802.3 Network status indicators LINK, CONDUCT, ERROR LEDs AES/EBU 1–4 25-pin female D-sub x4 Sampling rate 48 kHz Signal delay 0.
Dimensions 31 ENGLISH Dimensions 396 0.65 322 D:386 380 17.5 44 W:480 H:44.65 7.9 349.3 30 11 430 Units: mm Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corporation reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment, or options may not be the same in every locale, please check with your Yamaha dealer.
32 System Examples 4 System Examples ACU16-C Power Amp Control System This example shows how up to 32 Yamaha PCxxxxN series power amplifiers can be connected to a single ACU16-C for remote control and monitoring via NetworkAmp Manager.
33 ACU16-C/NHB32-C CobraNet Audio Distribution System This example shows how multiple AES/EBU channels can be distributed over long distances (up to 200 meters with 100Base-TX Ethernet cabling) to multiple power amplifiers. The NHB32-Cs handle AES/EBU to CobraNet conversion, while the ACU16-Cs handle CobraNet to analog conversion. Power amplifier control and monitoring can be performed on either PC.
34 System Examples MIDI Over CobraNet This example shows how MIDI mode, which is set in NetworkAmp Manager, can transmit MIDI Program Change and Control Change messages from one NHB32-C to another over CobraNet’s Serial Bridge feature. In this example, MIDI data from a Yamaha DME32 Digital Mixing Engine is fed through to a Yamaha DM2000 Digital Production Console. While MIDI mode is active, neither Amp Control data nor AD824 data can be transmitted. ex. Yamaha DME32 ex.
35 CobraNet Primary & Secondary These two examples show how the CobraNet PRIMARY and SECONDARY ports can be used to build redundancy into systems. In the first example, if a primary connection fails, the system automatically switches to secondary and operation continues uninterrupted. However, if the switching hub fails, the entire system stops working.
36 Troubleshooting Troubleshooting Unit Symptom Cannot power up? Cannot establish a connection with NetworkAmp Manager? Advice Make sure that the power cord is connected to a suitable AC wall outlet. Also make sure that the other end of the power cord is connected to the unit’s AC IN correctly. Use the supplied retaining clamp to ensure that the power cord cannot be disconnected inadvertently. Make sure that the POWER switch is set to the ON position.
System Errors ACU16-C NHB32-C NetworkAmp Manager Symptom Advice NetworkAmp Manager cannot control and monitor all power amps? Make sure that all power amps are powered up. Make sure that each power amp is assigned an exclusive amp ID. Check the RS-485 cable connection between each power amp. If a cable is not connected properly, or a cable is faulty, power amps further down the line will not be detected.
38 Appendix Appendix Connector Wiring Details ACU16-C/NHB32-C TO COMPUTER Port (RS-232C) Pin Connection 1 Unused 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 Unused NHB32-C COM Port (RS-422) Pin Connection 1 Unused 2 Rx– 3 Tx– 4 Tx+ 5 GND 6 Rx+ 7 RTS 8 CTS 9 Unused NHB32-C AES/EBU Ports Pin Connection 1 CH1/2 IN + 2 Pin Connection 14 CH1/2 IN – CH3/4 IN – CH3/4 IN + 15 3 CH5/6 IN + 16 CH5/6 IN – 4 CH7/8 IN + 17 CH7/8 IN – 5 CH1/2 OUT – CH1/2 OUT
Connector Wiring Details 39 Pin ENGLISH ACU16-C RS-485 Port (RJ-45) Connection 1 Unused 2 Unused 3 Unused 4 RxD/TxD+ 5 RxD/TxD– 6 Unused 7 GND 8 GND Cable Wiring Details Although only pins 4, 5, 7, and 8 are used, all pins should be terminated properly, so connect all eight pins even though only four are actually used.
Yamaha Manual Library http://www2.yamaha.co.jp/manual/english/ This document is printed on chlorine free (ECF) paper with soy ink. M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2002 Yamaha Corporation V955350 304IPCP15.