UTG NS-F310 Speaker Enceinte OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG MANUAL DE INSTRUCCIONES
Thank you for selecting this YAMAHA product. PRECAUTIONS Read this before using the speaker. • To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. • Install the speaker in a cool, dry, clean place - away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of electrical noise (transformers, motors). To prevent fire or electrical shock, do not expose this unit to rain or water.
PRECAUTIONS WHEN POSITIONING THE SPEAKERS The speaker is constructed with the majority of the weight located in its upper portion, and is thus susceptible to falling over if proper care is not taken to insure its stability. If the speaker falls over, it may damage the speaker or be the cause of injury (or even death) to person and/or damage to personal property. For safe and proper use of the speaker: • Position the speaker in a location that is solid, level, smooth, and low (with respect to the floor).
CONNECTIONS TO YOUR AMPLIFIER ■How to connect 1 2 Before making connections, make sure that the amplifier is switched off. Loosen the knob. Remove 10 mm (3/8”) of insulation from each end of the cables, and twist the exposed conductors together neatly and tightly, as shown below. 10 mm (3/8 ”) Tighten Loosen Red (+) Good 3 4 No Good Insert the bare wire. Tighten the knob and secure the cables. Test the firmness of the connection by pulling lightly on the cables at the terminal.
REMOVING THE FRONT COVER The front cover is attached to protect the speaker unit, but you can remove it if necessary. The front cover is fixed by magnets. Hold the speaker with one hand, and pull the front cover gently with the other to remove it. SPECIFICATIONS Type .........................................2-way bass reflex speaker system Non-Magnetic shielding type Driver .............................................8 cm (5/16”) cone woofer × 2 3 cm (1-3/16”) soft dome tweeter Impedance..................
■如何连接 1 2 拆下前面板 松开旋钮。 如下所示,剥去每根电缆末端 10 mm 绝缘层,然后将露出 的导线整齐并紧紧地拧在一起。 前面板由磁铁固定。一手扶住扬声器,另一手轻拉前面板以 将其拆下。 10 mm 3 4 安装前面板可以保护扬声器单元,但是如果需要,您可以将 其拆下。 插入裸线。 拧紧旋钮并紧固电缆。 轻拉端子上的电缆,检查连接是否牢固。 注意 • 请勿使裸露的扬声器电线互相接触,否则可能损坏扬声器 或放大器,或同时损坏两者。 • 请勿将绝缘部分插入孔中。否则可能没有声音。 ■使用香蕉插头时 注意 除非使用香蕉插头,否则请勿拔出此盖子。 香蕉插头 盖子 注意 • 当取下盖子时,小心不要触摸驱动单元,且不要用工具施 力。 • 前盖反面有磁体。取下前盖后,请勿将其靠近可能受磁体 影响的物体,如电视机、时钟、磁卡、磁盘等。 规格 1 2 3 朝身体方向拉盖子将其拔出。 拧紧端子旋钮。 只需将香蕉插头插入端子。 类型 ......................... 2 路低音反射扬声器系统 非磁屏蔽型 驱动单元 ....................