UA NS-P620 (NS-P620: NS-10MMT + NS-C10MM + YST-SW105) HOME CINEMA 5.1CH SPEAKER PACKAGE OWNER’S MANUAL NS-P620(UA)-PRE(02.04.3)a 1 02.4.
• Explanation of Graphical Symbols CAUTION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
18 19 Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
UNPACKING After unpacking, check that the following items are included. Speaker cables Main and rear speakers [10m] X4 X4 Speaker cables [4m] Center speaker X3 Subwoofer Mounting brackets SUPERWOOFER SYSTEM YST-SW105 STANDBY/ ON B.A.S.S. HIGH CUT X4 VOLUME MOVIE MUSIC 50Hz 150Hz 0 10 Screws X8 Pads (for NS-10MMT) X2 Nonskid pads (for YST-SW105) Subwoofer cable [3m] Fasteners X4 IV NS-P620(UA)-PRE(02.04.3)a 4 02.4.
English Thank you for selecting this YAMAHA NS-P620 Speaker Package. CAUTION: Read this before operating your unit. ● ● ● ● ● To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install the speakers in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors).
SPECIAL INSTRUCTIONS FOR U.K. MODEL For U.K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.
Before making connections, place all speakers in their respective positions. The positioning of the speakers is important because it controls the whole sound quality of this system. Place the speakers depending on your listening position by following the instructions below. Speaker configuration Placing speakers This speaker package employs a 6 speaker configuration: 2 main speakers, 2 rear speakers, a center speaker and a subwoofer. The main speakers are used for main source sound.
䡵 Mounting the rear speakers Mount the rear speakers on a shelf, rack or directly on the floor, or hang them on the wall. 1 To mount the rear speakers on a wall by using the provided mounting brackets Mounting bracket 1 Attach the bracket to the rear of the speaker by using the provided screws. Remove the provided pads from the backing sheet and put them at the lower corners of the speakers.
English 䡵 Placing the center speaker Place the speaker on TV whose top is flat or on the floor under the TV or inside the TV rack so that it is stabilized. When placing the speaker on top of the TV, to prevent the speaker from falling down, put the provided fasteners at four points on the bottom of the speaker and the top of the TV. Screen Notes ● Do not place the speaker on top of the TV whose area is smaller than the bottom area of the speaker.
CONNECTIONS Caution: Plug in the subwoofer and other audio/video components after all connections are completed. 䡵 An example of basic connections Center speaker Rear speakers Right Left Subwoofer To AC outlet Amplifier Right Left Main speakers E-6 NS-P620UA(02.4.4)b 6 02.4.
● Basically, connect the subwoofer to the line output (pin jack) terminal(s) of the amplifier. If your amplifier does not have any line output terminal, connect the subwoofer to the speaker output terminals of the amplifier. (Refer to page 9 for details.) * To connect with a YAMAHA DSP amplifier (or AV receiver), connect the SUBWOOFER (or LOW PASS etc.) terminal on the rear of the DSP amplifier (or AV receiver) to the L INPUT2 terminal of the subwoofer.
䡵 How to connect speaker cables For connections, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the connections are faulty, no sound will be heard from the speakers. Make sure that the + and – polarity markings of the speaker cables are observed and set correctly. If these cables are reversed, the sound will be unnatural and lack bass. Main/center/rear speakers Red: positive (+) Black: negative (–) 4 1 How to Connect: 1 Loosen the knob.
English 䡵 Connecting the subwoofer to speaker output terminals of the amplifier If your amplifier has only one set of main speaker output terminals Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the main speakers.
USING THE SUBWOOFER (YST-SW105) 䡵 Controls and their functions Front panel Rear panel ~ Ÿ Power indicator Lights up in green while the subwoofer is turned on. STANDBY/ON button Press this button to turn on the power. (The power indicator lights up in green.) Press again to set the subwoofer in the standby mode. (The power indicator does not light.) * This button can be used only when the POWER (›) switch is set in the ON position.
‹ $ INPUT2 terminals Used to input line level signals from the amplifier. (Refer to “CONNECTIONS” for details.) AUTO STANDBY (HIGH/LOW/OFF) switch This switch is originally set to the OFF position. By setting this switch to the HIGH or LOW position, the subwoofer’s automatic power-switching function operates as described below. If you do not need this function, leave this switch in the OFF position. * Make sure to change the setting of this switch only when the subwoofer is in the standby mode.
䡵 Adjusting the subwoofer before use Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer and the main speakers by following the procedures described below. Front panel Rear panel 1 2 Set the VOLUME control to minimum (0). 3 Make sure that the POWER switch is set to the ON position, then press the STANDBY/ ON button to turn on the subwoofer.
English 䡵 Frequency characteristics Adjustment of the VOLUME control and the HIGH CUT control should be changed depending on the room size, the distance from the subwoofer to the main speakers, sources, etc. Following figures show the optimum adjustment of each control and the frequency characteristics when this subwoofer is combined with NS-10MMT. Frequency characteristics of this subwoofer (YST-SW105) ● When combined with NS-10MMT YST-SW105 * One graduation of this control represents 10 Hz.
ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY (for YST-SW105) The theory of Yamaha Active Servo Technology has been based upon two major factors, the Helmholtz resonator and negative-impedance drive. Active Servo Processing speakers reproduce the bass frequencies through an “air woofer”, which is a port or opening in the speaker’s cabinet. This opening is used instead of, and performs the functions of, a woofer in a conventionally designed speaker system.
English TROUBLESHOOTING Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service center. Cause Problem What to Do No sound. Speaker cables are not connected securely. Connect them securely. Sound level is too low. Speaker cables are not connected correctly.
SPECIFICATIONS 䡵 NS-10MMT 䡵 YST-SW105 Type .............................. 2-way bass-reflex speaker system Magnetic shielding type Type ............... Advanced Yamaha Active Servo Technology Driver ....................................... 9 cm (3-9/16”) cone woofer 2.5 cm (1”) balanced dome tweeter Driver .............................................. 20 cm (8”) cone woofer Magnetic shielding type Amplifier Output .................................................. 100W/5Ω Impedance ...................