AB BLUETOOTH SPEAKER SYSTEM OWNER’S MANUAL
Caution: Read this before operating your unit. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 1 Install this unit in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. 2 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds.
SPECIAL INSTRUCTIONS FOR U.K. MODEL Contents IMPORTANT THE WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
Controls and functions Satellite speaker (Right) Satellite speaker (Left) Operation panel Rear panel (Red) Bass unit 4 En (White)
Controls and functions See the illustration on the left page as well. 4 (Bluetooth) button/indicator Performs pairing operations and disable a Bluetooth connection. Indicates the Bluetooth connection status. ■ Operation panel 1 p (power) button/indicator When p (power) is pressed, this unit will turn on and the indicator will light white.
Speaker placement/connections Place all the speakers before connections. You can also mount satellite speakers on the wall. (☞ page 7) Connect speaker cables, and then connect the power cable to a wall outlet. You can adjust angles of satellite speakers vertically. Placing the speakers Place the satellite speaker (Left) on the left side and the satellite speaker (Right) on the right side correctly as shown below to obtain appropriate sound at the listening position.
Speaker placement/connections ■ To mount the satellite speakers on the wall You can also mount the satellite speakers on the wall as shown below. Depending on the mounting direction, you can adjust angles of the satellite speakers vertically or horizontally. Wall/ 5 mm (13/64 in.) wall support 41 mm (full scale) Min. 20 mm (1-3/16 in.) Bottom side of the satellite speaker foot Make sure that the screws are securely caught by the narrow parts of the hole slots.
Speaker placement/connections Connecting the cables (Right) (Left) (Red) (White) Speaker cable Power cable (supplied) To a wall outlet 8 En 1 Connect the speaker cables matching the plug color to the corresponding jack color. 2 Connect the supplied power cable to the AC IN jack. 3 Connect the supplied power cable to a wall outlet. 4 Connect external devices. Connecting with the supplied cable For details on connections, see the owner’s manual supplied with the external device. 3.
Power Turning on/off the power Press p (power) to turn on/off the power. When the power is on, p (power) lights white. ■ Auto-standby function This unit is equipped with the auto-standby function which automatically sets this unit to standby mode in 10 minutes if no audio signal is input from the connection device. In standby mode, p (power) lights orange. On Pause (white) Standby (orange) 10 minutes If playback continues at a very low volume level, this unit will be in standby mode automatically.
Bluetooth connection and music playback By pairing (registering) and connecting with a Bluetooth device such as a smartphone, you can enjoy music from this unit wirelessly. Within 10 m (33 ft) Pairing (Registering) Pairing is an operation to register a device (hereafter referred to as “connection device”) on this unit for communications. Pairing is required when making a Bluetooth connection for the first time or pairing information is deleted.
Bluetooth connection and music playback Playing music via a Bluetooth connection On Disabling the Bluetooth connection Follow one of the procedures below to disable the Bluetooth connection. (A) Press (Bluetooth) to turn off the indicator. (B) Press p (power) to turn off this unit. (C) Disable the Bluetooth function on the connection device. (white) Switching the Bluetooth connection Play Only 1 device can connect to this unit at once.
Troubleshooting Refer to the table below if this unit does not operate properly. If your problem is not listed below, or if the problem persists, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. ■ General Problem No sound is output from either or both of the speakers, or the sound is too quiet. Cause p (power) is not turned on. Solution Turn on p (power). When the power is on, p (power) lights white.
Troubleshooting ■ Bluetooth Problem Cannot make this unit pair with the connection device, or cannot establish a connection. No sound is produced or the sound is interrupted during playback. Cause A pairing operation was not done within about 5 minutes after pressing and holding (Bluetooth). The connection device does not support A2DP. There is a device (microwave oven, wireless LAN, etc.) that outputs signals in the 2.4 GHz frequency band nearby. Another device is already connected to this unit.
Specifications ■ Bluetooth Bluetooth version ....................................................................................................... Ver. 3.0 Supported profile .......................................................................................................... A2DP Supported audio codec ......................................................................................... SBC, AAC RF output power ......................................................................................
Specifications Bluetooth • Bluetooth is a technology for wireless communication between devices within an area of about 10 meters (33 ft) employing the 2.4 GHz frequency band, a band which can be used without a license. • Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement. Handling Bluetooth communications • The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of equipment.
AVEEA11102A Important Notice: Guarantee Information for customers in EEA* and Switzerland English For detailed guarantee information about this Yamaha product, and Pan-EEA* and Switzerland warranty service, please either visit the website address below (Printable file is available at our website) or contact the Yamaha representative office for your country. * EEA: European Economic Area http://europe.yamaha.
