COMMAND LINK MULTIFUNCTION METER (ROUND) OPERATION MANUAL 6Y8-2819V-00
To the owner Thank you for choosing the Yamaha Command Link Multifunction Meter. This Operation Manual contains information you will need for proper operation. A thorough understanding of these simple instructions and of those in the Owner’s Manual of the outboard motor will help you obtain maximum enjoyment of your new Yamaha. This manual should be considered a permanent part of this meter and should remain with it even if the meter is subsequently sold.
The Command Link Multifunction Meter enables the display of information through digital communication with the engine. The operations of the set button and the mode button are described in this manual as follows. Optional parts such as the speed sensor, cooling water pressure sensor, TriducerMulti sensor, and GPS are described in this manual by assuming that the parts are installed and set up on the outboard motor.
2. Speed & Fuel meter unit ........ Description ................................ Activating the meter .................. Speedometer............................. Fuel meter ................................. Multifunction display .................. 16 17 17 18 19 19 Fuel flow display .................... Fuel economy display ............ Total fuel consumption display................................. Ambient water temperature display (optional: Triducer-multi sensor has been installed) ....................
1. Tachometer unit NOTE: Depending on the model of the outboard motor, some functions may not be compatible. For information on models which contain the compatible functions, consult a Yamaha dealer. Tachometer The tachometer shows the engine revolutions per minute. (Page 3) Trim meter The trim meter shows the trim angle of the outboard motor in 13 levels. (Page 3) Adjusting trolling speed or : To adjust the trolling speed randomly.
Description/Activating the meter Activating the meter When the engine start switch is turned to ON, the meter is activated and “ ” appears on the multifunction meter. Then, all the displays come on and the display switches to the normal display after the total hour display comes on.
Tachometer/Trim meter Tachometer Periodic maintenance notification When the hours of engine operation exceed 100 hours, the elapsed time from the previous maintenance period (when the meter was reset) blinks. or The tachometer shows the engine revolutions per minute. : To return to the normal dis- play. Trim meter The trim meter shows the trim angle of the outboard motor in 13 levels. Blinks NOTE: • The elapsed time blinks every time the engine is started until it is reset.
Multifunction display When the engine start switch is turned to OFF, the last display shown is shown first when the engine start switch is turned to ON again. The multifunction display shows various information using numeric values or graphics. : Press to switch between the displays. NOTE: If an optional sensor is not connected to the meter, the corresponding display will not be displayed.
Cooling water/engine temperature display Cooling water/engine temperature display The cooling water/engine temperature indi- NOTE: The cooling water/engine temperature display shows “L” for low and “H” for high. cator ( ) comes on and the cooling water temperature or the engine temperature is shown in 6 levels. When the engine overheats, the cooling water/engine temperature indicator ( blinks to warn of the malfunction.
Battery voltage display Tachometer unit Battery voltage display The battery voltage indicator ( ) comes on and the battery voltage of the engine is shown in 6 levels or the voltage value is shown. : Press to switch between the display formats. Battery voltage level Blinks When the battery voltage decreases below the voltage that is required by the engine, Battery voltage value the battery voltage indicator ( to warn of the malfunction.
Total hour/Trip hour display/Cooling water pressure display Total hour/Trip hour display The total hour display shows the total hours of engine operation and the trip hour display shows the trip hours (T). Cooling water pressure display (optional: cooling water pressure sensor has been installed) The cooling water pressure indicator ( ) comes on and the cooling water pressure is shown in 6 levels. : Press to switch between the display formats.
Oil pressure display (4-stroke models) NOTE: • The oil pressure display shows “L” for low and “H” for high. • The low oil pressure warning does not display the engine oil level. • Depending on the model of the outboard motor, the oil pressure display may not be available. • Depending on the operating conditions such as when the engine is operated at extremely low speeds, the oil pressure may be shown as low even when the engine is operating properly.
Oil level display (2-stroke models)/Water detection warning Oil level display (2-stroke models) The oil level indicator ( ) comes on and the engine oil level is shown in 3 levels. Water detection warning When water has accumulated in the water separator (fuel filter), the water detection warning indicator ( ) blinks to warn of the malfunction. This function is not available for outboard motors that are not equipped with the water detection warning function.
Changing backlight settings Adjusting trolling speed You can turn the backlight on or off, or change the brightness level of the backlight for all meters synchronized. You can adjust the trolling speed randomly by increasing or decreasing it approximately 50 r/min. When in the trolling speed setting mode, the display switches to the normal display when the engine speed is increased (within 3,000 r/min) using the throttle.
Changing settings (custom mode) Changing settings (custom mode) NOTE: Switching to custom mode In the custom mode, you can change the meter function settings. Each setting function number is shown in the tachometer display. 1. Turn the engine off and the engine start switch to ON. • Trolling is affected by currents and other operating conditions and may differ from the actual engine speed. • The default engine idle speed is reset automatically when the display is switched to the normal display.
02 (setting trim angle) You can set the trim angle to zero. Fully trim the outboard motor down. 1. Turn the engine off and the engine start switch to ON. 01 (resetting maintenance intervals) You can reset the elapsed time from the previous maintenance interval (when the meter was reset). 1. Turn the engine off and the engine start switch to ON. 2. (4 seconds): To activate the custom mode and to switch to the resetting display. 2. (4 seconds): To activate the custom mode. 3.
03 (setting corresponding engine) 03 (setting corresponding engine) You can select the engines that are compatible to this meter. The port outboard motor is set to “-1- (engine number 1)” and the starboard outboard motor is set to “-2- (engine number 2).” 1. Turn the engine off and the engine start switch to ON. 2. (4 seconds): To activate the custom mode. 3. (1 second) (2 times): Press to switch between the setting function numbers and to switch to the change settings display. 4.
Service functions CAUTION: Diagnosis You can display the self-diagnosis results of the engine. When a diagnosis code other than “-01-” is displayed, the engine cannot be operated normally. Consult a Yamaha dealer. (10 seconds): To display the diagnosis codes. When there are no malfunctions, the “-01-” diagnosis code is displayed.
Service functions Resetting engine number When replacing the engines of multiple outboard motors or resetting the setting order, reset all engine numbers to “-1- (engine number 1).” 1. Turn the engine off and the engine start switch to ON. 2. (10 seconds): “-00-” will be displayed for 1 second. 3. Turn the engine start switch to OFF. The engine number is reset after approximately 10 seconds. Turn the engine start switches to ON in order from port to starboard. 4.
2. Speed & Fuel meter unit NOTE: Speedometer Shows the speed of the boat. You can switch the displayed unit to miles per hour (mph), knots, or kilometers per hour (km/h). (Page 18) Fuel meter The fuel meter shows the remaining fuel level in 8 levels. (Page 19) Multifunction display (Page 19) · You can switch each engine information and show it using numeric values.
Description/Activating the meter Description Activating the meter When the engine start switch is turned to ON, the meter is activated and “ ” appears on the multifunction meter. Then, all the displays come on and the display switches to the normal display after a few seconds.
Speedometer The speedometer shows the ground speed or the water speed of the boat. To display the ground speed, the GPS must be connected to the meter. To display the water speed, an optional sensor (speed sensor or Triducer-Multi sensor) must be connected to the meter. NOTE: • If no operations are carried out for 30 seconds or more, the display returns to the normal display.
Fuel meter/Multifunction display Fuel meter FLOW The fuel meter shows the remaining fuel level in 8 levels and all the segments are displayed when the fuel tank is full. When the fuel level is low, the last segment blinks. ECON TTL NOTE: The fuel sensor setting can be changed according to the fuel sensor type. To change the fuel sensor setting, see “02 (setting fuel sensor)” in “Changing settings (custom mode).
Fuel flow display When the engine start switch is turned to OFF, the last display shown is shown first when the engine start switch is turned to ON again. Fuel flow display FLOW shows the total fuel consumption per hour of all engines. • To change the various settings, see “Changing settings (custom mode).” • If an optional sensor is not connected to the meter, the corresponding display will not be displayed.
Fuel economy display/Total fuel consumption display Total fuel consumption display TTL shows the total fuel consumption of all engines. Fuel economy display ECON shows the distance traveled per unit of fuel. The TTL display cannot measure over 1,999 gallons or 1,999 liters. When there are more than 1,999 gallons or 1,999 liters of fuel, the numeric value blinks to indicate an overflow.
Ambient water temperature display/Depth display Depth display (optional: Triducer-multi sensor has been installed) DPTH shows the water depth. NOTE: You can select to show feet (F) or meters (m) on the DPTH display. To change the displayed unit, see “01 (setting displayed units)” in “Changing settings (custom mode).” NOTE: You can select to show Fahrenheit (°F) or Celsius (°C) on the TEMP display. To change the displayed unit, see “01 (setting displayed units)” in “Changing settings (custom mode).
Clock/Trip display/Changing backlight settings Trip display (optional: speed sensor has been installed) TRIP shows the information from the speed sensor converted to the distance traveled. Clock (optional: GPS has been installed) The clock shows the time in 12 hours. The local time is easily displayed by calculating the longitude information received from the GPS communication data. Set the time as necessary. Setting the time: 1. : To activate the time setting mode and switch to the time setting display.
Changing settings (custom mode)/01 (setting displayed units) Changing settings (custom mode) 2. (4 seconds): To activate the custom mode. 2. (4 seconds): To activate the custom mode and to switch to the change settings display. 3. : Press to switch between the displays. Speedometer TRIP (trip) FLOW (fuel flow) ECON (fuel economy) 3. (1 second): Press to switch between the setting function numbers and to switch to the change settings display.
01 (setting displayed units) 4. : Press to switch between the displays. In addition, you can select to not show the display. Speedometer You can select to show miles per hour (mph), kilometers per hour (km/h), or knots. The default setting is miles per hour (mph). TRIP You can select to show miles (mile), nautical miles (nm), kilometers (km), or not to show the display. The default setting is miles (mile).
02 (setting fuel sensor) You can set the fuel sensor type that is connected to this meter. 1. Turn the engine off and the engine start switch to ON. 03 (setting correction value) You can calibrate the displayed fuel flow value within –7 to +7 percent. The difference in the fuel consumption display and the actual fuel consumption is calibrated. 2. (4 seconds): To activate the custom mode. 3. (1 second): To switch between the setting function numbers and to switch to the change settings display. 4.
03 (setting correction value) NOTE: • The fuel flow display may differ depending on the operating conditions. • When the fuel flow calibration value is changed, the FLOW, TTL, and ECON displays are shown calibrated.
Activating for the first time/Setting the initial settings 3. Setting up the meters Activating for the first time To install the meters and the optional sensors and to connect the meters to the engine, see the “Command Link Multifunction Meter Installation Manual.” Be sure to follow the procedures in “Activating for the first time” and “Setting the initial settings.” If the procedures are performed incorrectly, the engine number will change, resulting in improper operation. 1. Installing the meters 2.
YAMAHA MOTOR CO., LTD. Printed in Japan March 2005 – 1.