I A N O N U M E R I Q U E Owner’s Manual Bedienungsanleitung Mode d’emploi ENGLISH P I A N O P DEUTSCH D I G I T A L ESPAÑOL FRANÇAIS Manual de instrucciones EN DE FR ES
SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: ENGLISH Power supply/AC power adaptor Water warning • Only use the voltage specified as correct for the instrument.
Connections Saving data • Before connecting the instrument to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum. Also, be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level.
Introduction ENGLISH Thank you for purchasing the Yamaha Digital Piano! We recommend that you read this manual carefully so that you can fully take advantage of the advanced and convenient functions. We also recommend that you keep this manual in a safe and handy place for future reference.
Table of Contents Introduction Please read this section first. Main Features..................................................... 6 Accessories ......................................................... 6 Panel Controls and Terminals............................ 8 Before Using the Instrument ........................... 10 Turning the Power On ...............................................10 Setting the Volume .....................................................10 Using the Pedals...........................
Panel Controls and Terminals Panel Controls and Terminals e r t y u i o !0 !1 !2 ENGLISH q w A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 Front panel q [STANDBY/ON] switch page 10 For turning the power on or off. w [MASTER VOLUME] dial page 10 For adjusting the volume level of the entire sound. e [DEMO] button page 12 For playing the demo songs. r [TRANSPOSE] button page 25 For recording your keyboard performance.
Panel Controls and Terminals !4 !5 !6 !7 !8 ENGLISH !3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7 !9 @5 @0 @1 @2 @3 @4 Rear panel @0 USB [TO DEVICE] terminal page 47 For connecting the instrument to a USB storage device, allowing saving/loading of data to and from the connected device.
Before Using the Instrument Before Using the Instrument Turning the Power On 1. Connect the power adaptor’s DC cable to the [DC IN 16V] jack. ENGLISH 2. Plug the AC adaptor into an AC outlet. WARNING Use the specified adaptor (PA-301, PA-300B or an equivalent recommended by Yamaha) only. The use of other adaptors may result in irreparable damage to both the adaptor and the Instrument. (The shape of plug differs depending on locale.
Before Using the Instrument Using the Pedals NOTE If the sustain pedal doesn’t work, make sure that the pedal cord is properly plugged into the jack. FC4 TERMINOLOGY ENGLISH Sustain Pedal (Sustain Pedal jack) This jack is for connecting the included foot switch FC4. The pedal functions in the same way as a damper pedal on an acoustic piano. Connect the included foot switch FC4 to this jack and press the pedal to sustain the sound.
Reference Listening to the Demo Songs Listening to the Demo Songs Demo songs are provided that effectively demonstrate each of the instrument’s voices. ENGLISH 3 4 4 3 1. Press the [STANDBY/ON] switch to turn the power on (page 10). When the power is turned ON, one of the voice button indicators will light. NOTE 2. Adjust the volume (page 10). Initially set the [MASTER VOLUME] dial about half way between the “MIN” and “MAX” settings.
Using the 50 Piano “Preset” Songs Using the 50 Piano “Preset” Songs Listening to the 50 Piano Preset Songs The instrument provides performance data of 50 piano songs. You can simply listen to these songs (page 60) or use them for practice (page 14). 1 5 2 1. Press the [SONG SELECT] button a few times until the “PRESET” indicator lights. 2. Press the [–/NO], [+/YES] buttons to select the number of the tune you want to play. The number will appear on the display.
Using the 50 Piano “Preset” Songs Practicing a One-Hand Part Using the 50 Preset Songs (Part Cancel Function) The 50 preset songs have separate left- and right-hand parts on individual parts. You can turn the left- and right-hand parts on or off as required so you can practice the corresponding part (the part that is turned off) on the keyboard. The right-hand part is played by [RIGHT] and the left-hand part is played by [LEFT]. ENGLISH 3 2 1 1. Turn off the playback part you wish to practice.
Using the 50 Piano “Preset” Songs A-B Repeat for the 50 Preset Songs The A-B Repeat function can be used to continuously repeat a specified phrase within a preset song. Combined with the Part Cancel function (page 14), this provides an excellent way to practice difficult phrases. ENGLISH 2 3 4 1. Select and play a preset song. 2. Press the [TEMPO/FUNCTION] button at the beginning of the phrase you want to repeat. This sets the “A” point ( will appear on the display). 3.
Selecting & Playing Voices Selecting & Playing Voices Selecting Voices ENGLISH Voice Name Select the desired voice by pressing one of the Voice buttons. [STRINGS/OTHERS] button Pressing the [STRINGS/OTHERS] button switches among the following eleven voices. Display Voice Name o 1 STRINGS 1 o 2 STRINGS 2 o 3 CHURCH ORGAN 2 o 4 HARPSICHORD o 5 E.CLAVICHORD o 6 VIBRAPHONE o 7 CHOIR o 8 GUITAR o 9 WOOD BASS o10 BASS & CYMBAL o11 E.
Selecting & Playing Voices Combining Voices (Dual) You can play voices simultaneously across the entire range of the keyboard. In this way, you can combine similar voices to create a thicker sound. 1. Press two voice buttons at the same time (or press one voice button while holding another) to engage Dual. The voice indicators of both selected voices will light when Dual is active. Play the keyboard.
Selecting & Playing Voices Splitting the Keyboard Range and Playing Two Different Voices ([SPLIT]) Split enables you to play two different voices on the keyboard — one with the left hand and another with the right hand. For example, you can play a bass part using the Wood Bass or Electric Bass voice with the left hand, and a melody with the right hand. ENGLISH Split point (default setting: F#2) Bass voice Melody 3 1. Press the [SPLIT] button to engage Split. 1245 NOTE The [SPLIT] button lights.
Selecting & Playing Voices 3. Press a voice button to select a voice for the right If you want to use a voice selected via the [STRINGS/OTHERS] button, press the [STRINGS/OTHERS] button several times to call up the desired voice. The voice number of the [STRINGS/OTHERS] button is displayed on screen. 4. Press the corresponding voice button while holding the [SPLIT] button to select a voice for the left hand. The indicator of the left voice button will light while the [SPLIT] button is pressed.
Selecting & Playing Voices Adding Variations to the Sound – [BRILLIANCE]/ [REVERB]/[EFFECT]/“Damper Resonance” [–/NO] [+/YES] buttons [BRILLIANCE] button [EFFECT] button ENGLISH [REVERB] button [BRILLIANCE] You can use this control to adjust the brilliance of the tone and change the tonality to suit your preference.
Selecting & Playing Voices [EFFECT] OFF: When no effect is selected, no EFFECT indicator is lit. CHORUS: A shimmering, broadening effect. PHASER: Adds a sweeping effect to the sound. TREMOLO: Adds an animated, vibrating effect to the sound. ROTARY SP: Adds the vibrato effect of a rotary speaker. To select an effect type, press the [EFFECT] button a few times until the indicator corresponding to the desired type lights (the indicators light in sequence each time you press the [EFFECT] button).
Selecting & Playing Voices Touch Sensitivity – [TOUCH] [–/NO] [+/YES] buttons ENGLISH [TOUCH] [TOUCH] button NOTE You can select four different types of keyboard touch sensitivity — HARD, MEDIUM, SOFT or FIXED — to match different playing styles and preferences. HARD: Requires that the keys be played quite hard to produce maximum loudness. MEDIUM: Produces a fairly “standard” keyboard response. SOFT: Allows maximum loudness to be produced with relatively light key pressure.
Selecting & Playing Voices Transposition – [TRANSPOSE] The instrument’s Transpose function makes it possible to shift the pitch of the entire keyboard up or down in semitone intervals to facilitate playing in difficult key signatures, and to let you easily match the pitch of the keyboard to the range of a singer or other instruments. For example, if you set the transposition amount to “5,” playing key C produces pitch F.
Selecting & Playing Voices Using the Metronome The instrument features a built-in metronome for convenience in practicing and use with the Recording features. 1 2 [–/NO] [+/YES] buttons ENGLISH [TEMPO/FUNCTION –, +] buttons 1. Press the [METRONOME] button to start the metronome. The metronome sound is turned on. The beat indicator flashes at the current tempo.
Recording Your Performance Recording Your Performance You cannot record the performance to the connected USB storage device directly. The recorded songs are saved to the instrument automatically. If you want to save data to the device, perform the Save operation (page 31) after stopping recording. TERMINOLOGY NOTE Recording vs. Saving: The format of performance data recorded on an MD differs from that of data recorded on the instrument. An MD records audio signals.
Recording Your Performance 2. Press the [REC] button to engage Record Ready mode. This automatically selects an empty file (U01–U03) for recording and makes the RIGHT part’s indicator turn red. If all file numbers contain recorded data, File U01 will be selected. This simply enables recording; to start recording, go on to step 3. The [PLAY/PAUSE] indicator will flash at the current METRONOME tempo setting.
Recording Your Performance Re-recording a previously recorded song If you are not satisfied with the recording, you can record it again. Using the following operation. 1. Select a voice or voices (and other settings) for recording, if necessary. Repeat step 1 on page 25 if you wish to change the previous settings. 2. Press the [REC] button again to re-engage Record The selected part’s indicator lights in red. Follow the procedure from step 3 in “Recording a performance quickly” on page 26 to re-record.
Recording Your Performance Recording to RIGHT/LEFT This lets you record the right and left parts separately. Since you can record the left part while playing back the right, this is useful for independently recording both parts of a duet. ENGLISH 3 2 3 2 1 1. Make all the initial settings. Same as step 1 in “Recording a performance quickly” on page 25. 2. Select a file (U01–U03) to record.
Recording Your Performance The song recorder records the following data: Data in addition to the notes and voices you play is recorded. This data includes “Individual Parts” and “Entire Song.” See below.
Recording Your Performance Changing the Initial Settings (data recorded at the beginning of a song) The initial settings (data recorded at the beginning of a song) can be changed after the recording. For example, after recording, you can change the voice to create a different ambience or adjust the song tempo to your taste. ENGLISH You can change the following initial settings.
Handling Recorded Songs with a USB Storage Device Handling Recorded Songs with a USB Storage Device You can handle recorded songs (save, load, and delete) with a USB storage device. You can also format the device or media. Before using a USB device, read the “Precautions when using the USB [TO DEVICE] terminal” section on page 53. Save NOTE You can save three recorded songs in the instrument to the USB storage device as SMF song files.
Handling Recorded Songs with a USB Storage Device Saving a Song 1 2 3 1 2 ENGLISH 1. Select a “USER” file to save. Select a “USER” file to save by using the [SONG SELECT] and [–/NO][+/YES] buttons. 2. Select a “USB” file in the device and save the “USER” file. NOTE If the selected file has no data, the file will not be saved (you cannot select a container for SMF songs — S00–S99). Confirm that the selected file has data by making sure that the indicator of [RIGHT] or [LEFT] is turned on.
Handling Recorded Songs with a USB Storage Device Loading a Song 1 3 1 2 CAUTION ENGLISH If the “USER” file (U03) on the instrument already contains data, this operation can result in overwriting of the data. Make sure to save important data to your computer beforehand. 1. Select a “USB” file in the device. After making sure that the USB storage device is connected to the instrument, press the [FILE] button (the “LOAD TO USER.” indicator lights).
Handling Recorded Songs with a USB Storage Device Deleting Song Files 1 2 3 1 2 ENGLISH 1. Select a “USB” file to be deleted. Press the [FILE] button. (The “DEL./FORMAT” indicator lights.) Then, hold the [FILE] button, simultaneously press the [–/NO][+/YES] buttons to select a file to be deleted. Two types of files will be displayed in order: • Sxx....... SMF songs • xxx....... External songs (commercially available songs or songs which have been edited on a computer) 2. Delete the file.
Handling Recorded Songs with a USB Storage Device Formatting the USB Storage Device 1 3 1 2 CAUTION ENGLISH If data is already saved to the USB storage device, be careful not to format it. If you format the device, all the previously saved data will be deleted. 1. Engage the file operation mode. Press the [FILE] button. (The “DEL/ FORMAT” indicator lights.) Then, while holding the [FILE] button, simultaneously press the [–/NO] and [+/YES] buttons.
Playing Back “USER” and “USB” Songs Playing Back “USER” and “USB” Songs The following types of songs are available. You can simply listen to these songs or use them for practice (pages 14, 15). “USER” songs NOTE • Songs (U01–U03) which you recorded to the instrument by using the record function (page 25). ENGLISH • External songs in the instrument Songs transferred from a computer (including commercially available songs and songs which have been edited on a computer).
Playing Back “USER” and “USB” Songs 43 1 2 1. Press the [SONG SELECT] button (the USER or USB indicator lights). ENGLISH 2. Press the [–/NO] [+/YES] buttons to select a song (Uxx*)/(xxx*) or (Sxx*)/(xxx*). The letters “xx” represent the song number. 3. Press the [PLAY/PAUSE] button to start playback. The current measure number appears on the display during playback. NOTE Recorded song playback cannot be started when the recorder contains no data.
Detailed Settings – [FUNCTION] Detailed Settings – [FUNCTION] You can set various parameters to make the best use of instrument functions, such as fine tuning the pitch or selecting a scale, etc. The following parameters are available. This instrument has eight main functions. Some of these main functions consist of a set of sub-functions. Function List ENGLISH Function Fine tuning of the pitch Selecting a scale Dual functions Sub-function — F2.1 40 C F2.
Detailed Settings – [FUNCTION] Basic Procedure in Function Follow the steps below to use the functions. If you become lost while using a function, return to this page and read the basic procedure. 2 4 5 3 1. Press the [TEMPO/FUNCTION] button to enter the Function. The [FUNCTION] indicator lights. NOTE Functions cannot be selected during Demo/PRESET/USER/USB song playback or in the File Operation and Record modes.
Detailed Settings – [FUNCTION] About Each Function The explanations here apply when entering the Function in step 5 on page 39. ENGLISH F1. Fine Tuning of the Pitch You can fine tune the pitch of the entire instrument. This function is useful when you play the instrument along with other instruments or CD music. Use the [–/NO] and [+/YES] buttons to lower or raise the pitch of the A3 key in approximately 0.2 Hz increments.
Detailed Settings – [FUNCTION] F2.2: Base Note F3.2: If you select a scale other than Equal Temperament, you need to specify the root. (You can also specify the root note with Equal Temperament selected, but it will have no effect. The base note setting is effective for tunings other than the Equal Temperament tuning.
Detailed Settings – [FUNCTION] F4. Split Functions ENGLISH This menu enables you to make various detailed settings for Split. By changing the split point or other setting, you can optimize the settings for the songs you play. Be sure to select the Split by pressing the [SPLIT] button before engaging Function. If Split is not engaged, will appear instead of and you will be unable to select the Split functions. Also note that you must exit Function before you can engage Split. F4.
Detailed Settings – [FUNCTION] F5.4: Keyoff Sample Volume This section provides a variety of other functions, including letting you assign the operation of the AUX pedal to one of several settings, and allowing you to select specific song channels for playback. Setting range: 0–20 Default setting: 10 You can adjust the volume of the keyoff sound (the subtle sound produced when the keys are released) for voices [GRAND PIANO 1], [HARPSICHORD], [E.CLAVICHORD]. F5.1: F5.5: AUX Pedal Setting range: 1.
Detailed Settings – [FUNCTION] F6. Metronome Volume Use this function to adjust the metronome volume. Setting range: 1–20 Default setting: 10 NOTE ENGLISH SHORTCUT: You can jump directly to the metronome functions by pressing the [TEMPO/FUNCTION] button while holding the [METRONOME] button. F7. MIDI Functions You can make detailed adjustments to the MIDI settings. For more information about MIDI, see the “About MIDI” section (page 48). F7.
Detailed Settings – [FUNCTION] Control Change ON/OFF Normally the instrument will respond to MIDI control change data received from an external MIDI device or keyboard, causing the voice on the corresponding channel to be affected by pedal and other “control” settings received from the controlling device (the keyboard voice is not affected). The instrument also transmits MIDI control change information when the pedal or other appropriate controls are operated.
Detailed Settings – [FUNCTION] ENGLISH F8. Backup Functions You can back up some settings, such as voice selection and reverb type, so that they will not be lost when you turn off the power to the instrument. If the backup function is turned on, the settings at power off are effective. If the backup function is turned off, the settings in memory are erased when you turn off the power. In this case, when you turn on the power to the unit, the default settings (the initial settings) will be used.
Connections Connections Connectors CAUTION Before connecting the instrument to other electronic components, turn off the power to all the components. Before turning the power on or off to all components, set all volume levels to minimum (0). Otherwise, electrical shock or damage to the components may result. 2 3 4 5 ENGLISH 1 1 USB [TO DEVICE] terminal This terminal allows connection to USB storage devices. Refer to “Connecting to a USB storage device” on page 49.
Connections 3 MIDI [IN] [OUT] terminals Use MIDI cables to connect external MIDI devices to these connectors. MIDI [IN]: Receives MIDI data. MIDI [OUT]: Transmits MIDI data. Refer to the “Connecting a Personal Computer” on page 50. About MIDI ENGLISH MIDI (Musical Instrument Digital Interface) is a standard format for data transmission/ reception. It enables the transfer of performance data and commands between MIDI devices and personal computers.
Connections Connecting to a USB storage device To connect to a USB storage device, be sure to read the section “Precautions when using the USB [TO DEVICE] terminal” on page 53. To display the data in the USB storage device To view the data of the USB storage device on the display, press the [SONG SELECT] button a few times until the “USB” indicator lights. If the “USB” indicator is lit before connecting the USB storage device, press the [EXIT] button to exit from “USB” and re-engage “USB.
Connections Connecting a Personal Computer By connecting a computer to the MIDI terminals, you can transfer data between the instrument and the computer via MIDI. To do this, install the USB MIDI interface driver and Musicsoft Downloader software. There are two ways you can connect the instrument to a computer: NOTE 1. Connecting the USB port on the computer to the instrument via a USB MIDI interface. 2. Using a MIDI interface and the instrument’s MIDI terminals.
Connections Transmitting Song Data between the Computer and the Instrument System requirement for Musicsoft Downloader • OS : Windows 2000/XP Home Edition/XP Professional/Vista * For XP and Vista, the 32-bit version is supported, but not the 64-bit version.
Data Backup Using a Computer Data Backup Using a Computer For maximum data security Yamaha recommends that you save your important data to your computer by using the Musicsoft Downloader (MSD) software. This provides a convenient backup if the internal memory is damaged. Data that can be saved ENGLISH ● Panel settings and recorded songs Panel settings are the same data that can be backed up using the Backup Functions (page 46). You can save the panel settings and recorded songs as one file.
Precautions when using the USB [TO DEVICE] terminal Precautions when using the USB [TO DEVICE] terminal This instrument features a built-in USB [TO DEVICE] terminal. When connecting a USB device to the terminal, be sure to handle the USB device with care. Follow the important precautions below. For more information about the handling of USB devices, refer to the owner’s manual of the USB device.
Handling the Floppy Disk Drive (FDD) and Floppy Disks (Optional) Handling the Floppy Disk Drive (FDD) and Floppy Disks (Optional) ENGLISH An optional floppy disk drive can be installed to this instrument. The floppy disk drive lets you save original data you’ve created on the instrument to floppy disk, and allows you to load data from floppy disk to the instrument. Be sure to handle floppy disks and treat the disk drive with care. Follow the important precautions below. Floppy Disk Compatibility 3.
Message List Message List Message Comment Displayed after factory presets are recalled. CLr CAUTION con Displayed when Musicsoft Downloader is started on a computer connected to the instrument. When this message appears, you cannot operate the instrument. E01 Indicates failure in accessing the USB storage device because the device or media is damaged. E02 Displayed when the song data is damaged or not recognized. E04 Indicates that the song data is too large to be loaded.
Troubleshooting Troubleshooting ENGLISH Problem Possible Cause and Solution The instrument does not turn on. The instrument has not been plugged in properly. Securely insert the female plug into the socket on the instrument, and the male plug into a proper AC outlet (page 10). A click or pop is heard when the power is turned on or off. This is normal when electrical current is being applied to the instrument. Noise is heard from the speakers or headphones.
Preset Voice List Preset Voice List Ø : Yes / — : No Voice Name Dynamic Key-Off Stereo Touch Sampling Sampling Sampling Response *1 *2 Voice Descriptions 1 GRAND PIANO 1 Ø Ø Ø Ø Recorded samples from a full concert grand piano. Also includes four levels of dynamic sampling, sustain samples, and key-off samples for exceptionally realistic acoustic grand piano sound. Perfect for classical compositions as well as any other style that requires acoustic piano.
Index Index Numerics 50 Piano Preset Songs .....................................................13 Effects............................................................................... 21 End (display) ................................................................... 55 ENGLISH Err (display) .................................................................... 55 A Export .............................................................................. 31 A-B Repeat....................................
Index N n y (display) .....................................................................55 n–Y (display) ...................................................................55 [SONG SELECT] button .......................................... 13, 37 Sostenuto pedal ............................................................... 43 Specifications................................................................... 68 SPLIT .........................................................................
Appendix Preset Song List / Liste der voreingestellten Songs / Liste des morceaux prédéfinis / Lista de canciones preseleccionadas Preset Song List / Liste der voreingestellten Songs / Liste des morceaux prédéfinis / Lista de canciones preseleccionadas No. 60 Title Composer 1 Invention No. 1 J.S.Bach 2 Invention No. 8 J.S.Bach 3 Gavotte J.S.Bach 4 Prelude (Wohltemperierte Klavier I No.1) J.S.Bach 5 Menuett G dur BWV.Anh.114 J.S.Bach 6 Le Coucou L-C.Daquin 7 Piano Sonate No.15 K.
Factory Setting List / Liste der Vorgabeeinstellungen / Liste des réglages / Lista de ajustes de fábrica Factory Setting List / Liste der Vorgabeeinstellungen / Liste des réglages / Lista de ajustes de fábrica Default Voice GRAND PIANO 1 Dual OFF Split OFF Backup Group F8.1 Split Left Voice Brilliance WOOD BASS NORMAL Reverb Type Preset for each voice Reverb Depth Preset for each voice Effect Type Preset for each voice Effect Depth Preset for each voice F8.4 F8.
MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI If you’re already very familiar with MIDI, or are using a computer to control your music hardware with computer-generated MIDI messages, the data provided in this section can help you to control the instrument.
MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI 4. PROGRAM CHANGE 7. SYSTEM EXCLUSIVE MESSAGES (Yamaha MIDI Format) Data format: [CnH] -> [ppH] CnH = Program event (n = channel number) ppH = Program change number P.C.#=Program Change number VoiceName GRAND PIANO 1 GRAND PIANO 2 ELECTRIC PIANO 1 ELECTRIC PIANO 2 JAZZ ORGAN CHURCH ORGAN 1 STRINGS 1 STRINGS 2 CHURCH ORGAN 2 HARPSICHORD E.CLAVICHORD VIBRAPHONE CHOIR GUITAR WOOD BASS BASS & CYMBAL E.
MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI (2) Universal Non-Realtime Message (GM On) General MIDI Mode On Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] -> [F7H] F0H = 7EH = 7FH = 09H = 01H = F7H = or F0H = 7EH = XnH = Exclusive status Universal Non-Realtime ID of target device Sub-ID #1=General MIDI Message Sub-ID #2=General MIDI On End of Exclusive Exclusive status Universal Non-Realtime When received, n=0–F.
MIDI Data Format / MIDI-Datenformat / Format des données MIDI / Formato de datos MIDI
MIDI Parameter Change table (SYSTEM) Address (H) Size (H) Data (H) 00 00 00 4 020C - 05F4* 01 02 03 04 7E 7F TOTAL SIZE 1 00 - 7F 00 00 Parameter MASTER TUNE MASTER VOLUME XG SYSTEM ON RESET ALL PARAMETERS Description -50 - +50[cent] 1st bit 3 - 0 ➝ bit 15 - 12 2nd bit 3 - 0 ➝ bit 11 - 8 3rd bit 3 - 0 ➝ bit 7 - 4 4th bit 3 - 0 ➝ bit 3 - 0 0 - 127 00=XG system ON 00=ON (receive only) Default value (H) 00 04˛ ˛ 0 - 127 0 - 127 ************** 0 - 127 ************** Note Number : True voice Ø ˛ Ø ˛ Ø ˛ Ø ˛ ˛ Ø ˛ Ø Control Change 0,32 1 7 10 11 6,38 64,66,67 71-74 84 91,93 96-97 100-101 ˛ Pitch Bend P-155 Owner’s Manual / Bedienungsanleitung / Mode d’emploi / Manual de instrucciones *1 *1 *1 *1 *1 *1 *1 Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø ˛ ˛ Key's Ch's After Touch ˛ ˛ Ø ˛ Note ON Ø 9nH,v=1-127 Note OFF ˛ 9nH,v=0 Velocity 0-24 semi 9nH,v=1-127 3 3 Default Messages Altered Mode ˛ 1 - 16 1 -
: True # ˛ ˛ ˛ ˛ Ø ˛ Ø Ø Ø Ø Ø ˛ Ø Ø ˛ ˛ ˛ Ø Ø (120,126,127) (121) (122) (123-125) 0 - 127 Mode 2 : OMNI ON ,MONO Mode 4 : OMNI OFF,MONO Ø ˛ : Yes : No *1 Although these control change messages are not transmitted by panel operations, they may be transmitted during a song performance. Mode 1 : OMNI ON , POLY Mode 3 : OMNI OFF, POLY Notes: All Sound Off Reset All Cntrls Local ON/OFF All Notes OFF Active Sense Reset : : : Mes- : sages: : Aux Ø Ø : Song Pos. ˛ : Song Sel.
Specifications / Technische Daten / Caractéristiques techniques / Especificaciones Specifications / Technische Daten / Caractéristiques techniques / Especificaciones Model Size/Weight Dimensions (with music rest) Weight Keyboard Control Interface Display Panel Tone Generation Voices Polyphony Preset Types Effects Functions Preset Songs Recording Compatible Data Format Functions Overall Controls Storage Storage and Connectivity Connectivity Amplifiers and Speakers Power Supply Accessories Inc
EN Information for Users on Collection and Disposal of Old Equipment This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC.
FR Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques Le symbole sur les produits, l’emballage et/ou les documents joints signifie que les produits électriques ou électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd.
Yamaha Home Keyboards Home Page http://music.yamaha.com/homekeyboard/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2008 Yamaha Corporation WQ76270 812POCP?.
