YAMAHA AMPLIFICADOR DE POTÊNCIA P3500 P2500 P1500 MANUAL DE INSTRUÇÕES Introdução
Obrigado por adquirir um amplificador de potência Yamaha da Série P3500/2500/1500. Esta série de amplificadores de áudio combina desempenho de alta potência com confiabilidade. Ao mesmo tempo, a renomada atenção da Yamaha para com os detalhes dos circuitos, assegura uma excelente performance sonora. As conexões de entrada consistem de conectores tipo XLR balanceados, conectores para fone de ouvido 1/4” balanceados e cinta separadora.
1. Evite excesso de calor, umidade, poeira e vibração Mantenha a unidade longe de locais onde possa estar exposta a altas temperaturas ou umidade - tais como radiadores de aquecimento, aquecedores, fornos, etc. Evite também locais sujeitos a excessiva acumulação de poeira ou locais com excessiva vibração que possa causar algum dano físico ao equipamento. 2. Evite batidas Batidas muito fortes na unidade poderão danificá-la. Manuseie sempre o equipamento com cuidado. 3.
Painel Frontal ILUSTRAÇÃO: Força Liga/Desliga Proteção Força Canal A Sinal Limite Canal B Sinal Limite 1. Botão e indicador de FORÇA Este é o botão principal de FORÇA. Pressione para LIGAR o amplificador. Pressione novamente para DESLIGAR. O indicador POWER (FORÇA) acenderá quando o amplificador estiver LIGADO. 2. Indicador de PROTEÇÃO Este LED vermelho acenderá por aproximadamente seis segundos quando o amplificador for LIGADO, indicando que o sistema de proteção início-suave está funcionando.
Modo Stereo (Estereofônico) Bridge (Ponte) Alto-falante B-2 - CANAL - A-2 4-8 Ohms/Canal Stereo (Estereofônico) 8-16 Ohms Bridge (Ponte) B-1 - CANAL - A-1 4-8 Ohms/Canal Stereo (Estereofônico) 8-16 Ohms Bridge (Ponte) 1. Terminais de ENTRADA (CANAL A,B) Três tipo de terminais balanceados são disponíveis para os canais A e B. O terminal de entrada do canal A é utilizado no modo Bridge (Ponte).
potência do canal B. Neste modo a impedância mínima do alto-falante é de 4 ohms por canal. Modo BRIDGE (Ponte) Neste modo os canais A e B são ligados juntos e funcionam como um amplificador monoaural. A impedância mínima do alto-falante, neste modo, é de 8 ohms. Impedância dos Alto-falantes O amplificador série P3500/P2500/P1500 possui dois modos de operação: Stereo (Estereofônico) e Bridge (Ponte) e permite que você faça a conexão em paralelo de múltiplos sistemas de alto-falantes.
ILUSTRAÇÃO Parafuso Parafusos 3. Após remover aproximadamente 10mm da isolação nas pontas dos cabos dos alto-falantes, passe a ponta decapada destes cabos através dos orifícios dos terminais correspondentes e aperte os terminais para fixar firmemente os cabos. Consulte a seção anterior sobre Terminais de ALTO-FALANTES para determinar a polaridade correta.
ex. Capacidade de entrada contínua dos alto-falantes: 100W Impedância dos alto-falantes: 8 ohms FÓRMULA NUMÉRICA Neste exemplo a capacidade requerida do fusível é calculada como sendo 3.5[A]. Cabo do Alto-falante Se você utilizar um cabo de alto-falante longo, utilize um cabo que seja o mais espesso possível para evitar deterioração do fator de atenuação ou perda de potência dentro do cabo. Os terminais de alto-falantes desta unidade comportam a conexão de cabos de qualquer espessura.
Solução de Problemas A tabela a seguir lista as possíveis causas principais de operação anormal e as providências requeridas para saná-las. Lista também a operação do circuito protetivo para cada caso.
Meia Potência, THD+N ≤ 0.1% Estéreo RL = 8 ohms Distorção Harmônica Total (THD+N) f=20 Hz~20 kHz, Meia Potência Estéreo RL = 8 ohms RL = 4 ohms Ponte RL = 8 ohms Distorção Intermodular (IMD) f=60 Hz: 7kHz, 4:1, Meia Potência Estéreo RL = 8 ohms RL = 4 ohms Ponte RL = 8 ohms Separação de Canal Meia Potência, RL=8 ohms, f=1Khz Entrada máx ATT 600 ohms deriv. Ruído Residual Áudio DIN Razão Sinal/Ruído Áudio DIN, Entrada 600 ohms deriv.
Saída Terminais de retenção de 5 vias x2 Cinta separadora x2 0 dB = 0.775 Vrms, Meia Potência = ½ Nível de Potência de Saída (Potência Especificada) * A utilização de alto-falantes reativos de 2 ohms poderá causar superaquecimento, excessivo consumo de energia e desligamentos do aparelho. Observe que abaixo de 2 ohms o limitador PC entrará em ação. Teste o sistema completamente antes de utilizar alto-falantes de 2 ohms em aplicações reais. Especificações sujeitas a alteração sem aviso prévio.