TOSHIBA Satellite P500 / Satellite P505 Qosmio X500 / Qosmio G60 / Qosmio X505 Satellite P500D / Satellite P505D Satellite P507 / Satellite P507D Portable Personal Computer User's Manual
Copyright © 2009 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
Trademarks IBM is a registered trademark and IBM PC is a trademark of International Business Machines Corporation. Windows and Microsoft are registered trademarks of Microsoft Corporation. DirectX, AcriveDesktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation. Intel, Intel Core, Celeron, Centrino and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
FCC information FCC notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC and/or R&TTE Directive 1999/5/EC. Responsible for CE“TOSHIBA EUROPE GMBH, Hammfelddamm 8, marking: 41460 Neuss, Germany. Manufacturer: Toshiba Corporation, 1-1 Shibaura 1-chome, Minato-ku, Tokyo, 105-8001, Japan.
Modem warning notice This information is applicable to the models equipped with a built-in modem. Conformity Statement The equipment has been approved to [Council Decision 98/482/EC - "TBR 21"] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN).
Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ■ The telephone number of the line to which you will connect the modem. ■ The registration number that is located on the device US : CXSMM01BRD02D450 The FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer outside of the main system label.
Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other ent
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. 3. The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C.
Notes for use of this device in New Zealand ■ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
second ring cadences) is not destroyed. ■ The preferred method of dialling is to use DTMF tones (ATDT...) as this is faster and more reliable than pulse (decadic) dialling. If for some reason you must use decadic dialling, your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand “Reverse dialling” standard.
Following information is only for EU-member states: Disposal of products WEEE Dustbin Symbol The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres. The black bar indicates that the product was placed on the market after August 13, 2005.
ENERGY STAR® Program Your Computer model may be ENERGY STAR® compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency.
Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic BD Combo UJ141/BD-R/RE UJ240 with Labelflash™ ■ The BD Combo/BD-R/RE drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
Hitach-LG Data Storage DVD Super Multi GT20N/GT20F with Labelflash™ ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
TOSHIBA SAMSUNG STORAGE TECHNOLOGY DVD Super Multi TS-L633C/TS-L633Y ■ THIS DVD WRITABLE DRIVE EMPLOYS A LASER SYSTEM TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT EVER REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. ■ USE OF CONTROLS OR ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TEAC DVD Super Multi DV-W28S-VTG/DV-W28S-VTH ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
Panasonic DVD Super Multi UJ890AD/UJ890ED with Labelflash™ ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
International Precautions CAUTION: This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT." To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest "AUTHORIZED service station." To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
General Precautions General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
General Precautions To keep your computer in prime operating condition, protect your work area from: ■ Dust, moisture, and direct sunlight. ■ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ■ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters. ■ Extreme heat, cold, or humidity. ■ Liquids and corrosive chemicals.
General Precautions ExpressCard overheating Some PC and ExpressCards can become hot during prolonged use which may result in errors or instability in the operation of the device in question. In addition, you should also be careful when you remove a PC or ExpressCard that has been used for a long time. Mobile phones Please be aware that the use of mobile phones can interfere with the audio system.
Table of Contents Table of Contents Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxi Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxii Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxii Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxii Keys . . . . . . . . . . . . . . . . . . . . .
Table of Contents DVDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BD-R/RE drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BD Combo drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DVD Super Multi drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC adaptor . .
Table of Contents Using the microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the TOSHIBA Face Recognition . . . . . . . . . . . . . . . . . . . . . . . Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to register the Face Recognition Data . . . . . . . . . . . . . . . . . . How to Delete the Face Recognition Data . . . . . . . . . . . . . . . . . . . How to launch the help file . . . . . . . . . . . . . . . . . .
Table of Contents Bluetooth Stack for Windows by TOSHIBA (depends on the model you purchased) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43 Wireless communication switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44 Wireless activity LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44 LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44 LAN cable types . . . . . . .
Table of Contents Panel power off/on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 System Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 Chapter 7 HW Setup Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 HW Setup Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Chapter 8 Optional Devices ExpressCard . . . . . . . . . . . . . .
Table of Contents LCD panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8 Solid State drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9 Recovery Media Creator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9 Hard disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9 BD drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preface Preface Congratulations on your purchase of the TOSHIBA Satellite P500 / Satellite P505 / Satellite P507, Qosmio X505, Qosmio X500, Qosmio G60, Satellite P500D / Satellite P505D / Satellite P507D Series Series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing.
Preface Chapter 4, Operating Basics, includes instructions on using the following devices: TouchPad, Sound System, optical media drives, modem, wireless communication and LAN. It also provides tips on care of the computer, and CD/DVDs. Chapter 5, The Keyboard, describes special keyboard functions including hot keys. Chapter 6, Power and Power-Up Modes, gives details on the computer's power resources and battery save modes.
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Introduction Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer's features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software The following software is preinstalled: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Windows® 7 Microsoft Internet Explorer TOSHIBA Value Added Package TOSHIBA Hardware Setup TOSHIBA Supervisor Password TOSHIBA Assist TOSHIBA ConfigFree TOSHIBA HDD Protection TOSHIBA DVD PLAYER TOSHIBA FingerPrint Utility (FingerPrint support model only) TOSHIBA Disc Creator TOSHIBA Recovery Media Creator TOSHIBA Face Recognition WinDVD BD for TOSHIBA ■ Corel MovieFactory® for TOSHIBA ■ TOSHIBA PC Health Monitor ■ T
Introduction Features Please visit your region’s web site for the configuration details of the model that you have purchased. Processor Built-in Your computer is equipped with one processor and processor type varies depending on model. To check which type of processor is included in your model, open the TOSHIBA PC Diagnostic Tool Utility by clicking Start J All programs J TOSHIBA J Utilities J TOSHIBA PC diagnostic Tool. Chipset Depends on the model you purchased.
Introduction Video RAM Video RAM depends on the model you purchased. Mobile Intel® GM45 Express Chipset model: Video RAM capacity shares with main memory, and the proportion depends on Dynamic Video Memory Technology.
Introduction Power Battery Pack Your computer is powered by a rechargeable lithium-ion battery pack. Disclaimer (Battery Life)*3 For more information regarding Battery Life, please refer to the Disclaimers section in Appendix E or click the *3 above. RTC Battery The internal RTC battery backs up the Real Time Clock and calendar. AC Adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord.
Introduction BD-R/RE drive with Labelflash™ User’s Manual Some models are equipped with a full-size BD-R/ RE drive module that lets you record data to rewritable CD/DVD/BDs. It reads BD-ROM discs at maximum 6 speed, BD-ROM (DL) discs at maximum 6 speed, DVD-ROM's at maximum 8 speed and CD-ROM's at maximum 24 speed. It writes CD-R's at up to 24 speed, CD-RW's at up to 4 speed, DVD-R's at maximum 8 speed, DVDRW's at maximum 6 speed.
Introduction BD Combo drive with Labelflash™ User’s Manual Some models are equipped with a full-size BD Combo drive module that lets you record data to rewritable CD/DVDs. It reads BD-ROM discs at maximum 6 speed, BD-ROM (DL) discs at maximum 6 speed, DVD-ROM's at maximum 8 speed and CD-ROM's at maximum 24 speed. It writes CD-R's at up to 24 speed, CD-RW's at up to 4 speed, DVD-R's at maximum 8 speed, DVDRW's at maximum 6 speed.
Introduction DVD Super Multi drive User’s Manual Some models are equipped with a full-size DVD Super Multi drive module that lets you record data to rewritable CD/DVDs. It reads DVDROM's at maximum 8 speed and CD-ROM's at maximum 24 speed. It writes CD-R's at up to 24 speed, CD-RW's at up to 24 speed, DVD-R's at maximum 8 speed, DVD-RW's at maximum 6 speed.
Introduction Display The computer's LCD panel supports high-resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-In Thin-film transistor color LCD is available in two sizes: 18.4" wide, 1680 horizontal x 945 vertical pixels 18.4" wide, 1920 horizontal x 1080 vertical pixels Disclaimer (LCD)*4 For more information regarding LCD, please refer to the Disclaimers section in Appendix E or click the *4 above.
Introduction Universal Serial Bus (USB 2.0) The computer has Universal Serial Bus ports that comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard. (The ports also support USB 1.1.) Ports with the icon ( ) have USB Sleep and Charge function. eSATA/USB combo port eSATA/USB combo port port supports the USB 2.0 and the eSATA function. i.
Introduction Headphone(S/P DIF) jack This jack outputs analog audio signals. This jack can be used also as S/P DIF jack and enables connection of optical digital correspondence apparatus. Microphone Jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. Communications User’s Manual Modem Where present, it provides capability for data and fax communication. It supports V.90 (V.92).
Introduction The transmission speed over the wireless LAN, and the distance over which the wireless LAN can reach, may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, client design and software/hardware configurations. The transmission rate described is the theoretical maximum speed as specified under the appropriate standard - the actual transmission speed will be lower than the theoretical maximum speed.
Introduction Hot Keys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program. Instant Security The hot key function Fn + F1 blanks the screen and disables the computer, providing data security. Display Automatic Power Off *1 This feature automatically cuts off power to the internal display when there is no keyboard input for a specified time. Power is restored when any key is pressed.
Introduction Hibernation This feature lets you turn off the power without exiting from your software. The contents of main memory are saved to the hard disk so that when you turn on the power again, you can continue working right where you left off. Refer to the Turning off the power section in Chapter 3, Getting Started, for details. Sleep Mode If you have to interrupt your work, you can turn off the power without exiting from your software.
Introduction User’s Manual TOSHIBA Flash Cards This utility supports the following functions. ■ Hot key function ■ TOSHIBA utility launcher function TOSHIBA Components Common Driver TOSHIBA Components Common Driver contains the module required for the utility which TOSHIBA offers. TOSHIBA Accessibility The TOSHIBA Accessibility utility provides support to movement impaired users when they need to use the TOSHIBA Hot-key functions.
Introduction Utilities and Applications This section describes pre-installed utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides easy access to help and services. HW Setup This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use.
Introduction WinDVD BD for TOSHIBA This software is provided for playback of Blu-ray Disc. It has an on-screen interface and functions. To run WinDVD BD for TOSHIBA, click J All Programs J InterVideo WinDVD J WinDVD BD for TOSHIBA. Corel DVD MovieFactory® for TOSHIBA You can edit digital video and make a DVD-Video and support Label Flash function. The availability of Label Flash function depends on the model you purchased.
Introduction TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks. To run ConfigFree, click , select All Programs, TOSHIBA and then click ConfigFree.
Introduction Windows Mobility Center This section describes the Windows Mobility Center. Mobility Center is a utility for accessing several mobile PC settings quickly in one window. A maximum of eight tiles are prepared as the operating system default. Two additional tiles are also added to your Mobility Center. Installing the "TOSHIBA Extended Tiles for Windows Mobility Center" package will add the following functions. ■ Lock Computer: Lock your computer without turning it off.
The Grand Tour Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The following figure shows the computer's front with its display panel in the closed position. 5 2 1 3 6 7 8 9 4 1. Infrared Receiver Window 2. Wireless Communication Switch 3. Wireless Activity LED 4. Multiple Digital Media Card Slot 5. DC in LED 6. Power LED 7. Battery LED 8. Disk LED 9.
The Grand Tour ■ Set the wireless communication switch to off in airplanes and hospitals. Check the wireless activity indicator. It will stop glowing when the wireless communication function is off. ■ Turn Wi-Fi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury.
The Grand Tour Disk LED Disk LED indicates that the hard disk drive or optical disc drive is being accessed. Multiple Digital Media Card Slot LED Multiple Digital Media Card Slot LED lights up when the Multiple Digital Media Card Slot is accessed. (Provided with some models) Left side The following figure shows the computer's left side. ■ Tray ODD 1 2 3 4 5 6 7 ■ Slot ODD 8 9 10 1. LAN Jack 2. eSATA/USB Combo Port 3. Universal Serial Bus (USB 2.0) Port 4. HDMI Port 5. i.
The Grand Tour ■ Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction. ■ Do not connect the LAN cable to a power supply. It could cause damage or malfunction. eSATA/ eSATA/USB Combo Port The eSATA/USB combo port supports the USB Universal Serial Bus (USB 2.0) Port The Universal Serial Bus Port complies with the USB 2.0 standard. HDMI Port This port allows you to connect digitally to an HDTV or home theater receiver. i.
The Grand Tour Right side The following figure shows the computer's right side. 1 2 3 4 5 6 7 1. Headphone (S/P DIF) jack 2. Microphone Jack 3. USB Serial Bus (USB 2.0) Ports 4. Modem Jack or TV In Port* 5. External Monitor Port 6. DC in 19V Jack 7. Security Lock Slot The right side of the computer * The figure shows the Modem Jack. User’s Manual Headphone (S/P DIF) jack This jack outputs analog audio signals.
The Grand Tour ■ Connection to any communication line other than an analog phone line could cause a computer system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■ Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX). ■ Never connect the built-in modem to a key telephone system for residences or offices.
The Grand Tour Backside The following figure shows the computer's back panel. 1. Cooling Vents 1 The backside of the computer Cooling Vents Cooling vents help prevent the CPU from overheating. Do not block the cooling vents. Make sure that foreign objects such as pins (or similar objects) are kept out of the vents, to avoid damaging the computer's circuitry.
The Grand Tour Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. 1 2 3 4 5 7 6 1. Hard Disk Cover 2. Battery Pack Lock 3. Battery Pack 4. Battery Release Latch 5. Hard Disk Cover 6. Memory Module Cover 7. Cooling Vents The underside of the computer User’s Manual Hard Disk Cover This cover protects the hard disk. Battery Pack Lock Slide this lock to prepare the battery pack for removal.
The Grand Tour User’s Manual Memory Module Cover This cover protects two memory module sockets -one or two modules are pre-installed. Refer to the Memory expansion section in Chapter 8, Optional Devices. Cooling Vents Cooling vents help prevent the CPU from overheating.
The Grand Tour Front with the display open This section shows the front of the computer with the display open. Refer to the appropriate illustration for details. To open the display, lift the front of the display. Position the display at a comfortable viewing angle. 1 3 2 4 9 16 17 18 5 19 IBA TOSH 6 10 11 12 13 14 7 llite Sate 8 15 1. Web Camera LED* 2. Web Camera* 3. Built-in microphone* 4. Wireless LAN Antenna (Not shown)* 5. Speaker 6. TouchPad 7. Fingerprint Sensor* 8.
The Grand Tour User’s Manual Web Camera LED The Web Camera LED indicates whether the web camera is working or not. (Provided with some models) Web Camera Use the web camera to take your picture or send your image to web contacts. (Provided with some models) Built-in microphone The microphone is used with the Web Camera to talk to other Web Camera users and to record messages on windows media.
The Grand Tour User’s Manual Power Button Turns the computer on and off, puts it into Hibernation mode, and wakes it up from Sleep mode. eco Button Press this button to launch the eco application. CD/DVD/BD Button Press this button to launch an application program that allows for playing of CDs, DVDs or BDs. The application that is launched differs by model: Windows Media Player/TOSHIBA DVD PLAYER/WinDVD BD for TOSHIBA. Previous Button Skips backwards to the previous track, chapter or digital file.
The Grand Tour Optical Disc Drive An ATAPI interface controller is used for optical disc operation. When the computer is accessing an optical disc, an indicator on the system glows. Region codes for BD drive and media Optical disc drives and their associated media are manufactured according to the specifications of three marketing regions. Region codes can be set from WinDVD BD([Region] tab in [Setup] dialogue).
The Grand Tour BD-R/RE drive The full-size BD-R/RE drive module lets you record data to writable CD/ DVD/BDs as well as run either 12 cm (4.72") or 8 cm (3.15") for Tray type, 12 cm (4.72") for Slot type CD/DVDs without using an adaptor. Use only round standard (12cm) discs with this slot-loading optical drive. Any other size or shape disc may not be able to be removed from the slot and may damage the system as well as the disc. The read speed is slower at the centre of a disc and faster at the outer edge.
The Grand Tour BD Combo drive The full-size BD Combo drive module lets you record data to writable CD/ DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") for Tray type, 12 cm (4.72") for Slot type CD/DVDs without using an adaptor. Use only round standard (12cm) discs with this slot-loading optical drive. Any other size or shape disc may not be able to be removed from the slot and may damage the system as well as the disc. The read speed is slower at the centre of a disc and faster at the outer edge.
The Grand Tour DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to writable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") for Tray type, 12 cm (4.72") for Slot type CD/DVDs without using an adaptor. Use only round standard (12cm) discs with this slot-loading optical drive. Any other size or shape disc may not be able to be removed from the slot and may damage the system as well as the disc.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. Refer to Chapter 6, Power and Power-Up Modes, for details.
The Grand Tour Remote controller A remote controller, which is provided with some models, enables you to perform some functions of your computer from a distance. You can use your remote controller with Media Center to play CDs, DVDs, BDs and videos, as well as view pictures. The remote controller helps you to control the playback of a movie with Media Center. You can use the remote controller to: ■ Navigate and control all Media Center windows. ■ Control the video.
The Grand Tour Slim size remote controller 1 2 3 4 20 19 5 18 17 16 15 14 13 6 12 10 7 8 9 11 1. CD/DVD/BD Button 2. LCD Brightness Down 3. LCD Brightness Up 4. Power 5. LED On/Off 6. Arrows 7. More Information 8. Fast Forward 9. Play/Pause 10. Skip 11. Stop 12. Replay 13. Rewind 14. Start 15. Back 16. Mute 17. OK 18. Volume 19. Volume + 20. DVD Menu User’s Manual CD/DVD/BD button Press this button to launch Windows Media Player / DVD Video Player / WinDVD BD for TOSHIBA.
The Grand Tour User’s Manual Power Starts or terminate the operating system.This button functions like the power button of your computer. By default, the Sleep mode is equivalent to the power off state of your computer. To change the setting, click Start J Control panel J System and Security J Power Options J Choose what the power button does. The following four options are available: Do nothig, Sleep, Hibernate and Shut down. Volume + Increases the volume while viewing DVDs or playing CDs.
The Grand Tour Fast forward Moves the media (video, DVD, music, and so on) forwards. Replay Moves media backward (seven seconds for videos, one music track or one DVD chapter at a time). Stop Stops the currently playing media. Skip Moves media forward (30 seconds for videos, one music track or one DVD chapter at a time). Using the remote controller Some computers include a remote control unit, which allows you to control some of your computer’s functions from a distance.
The Grand Tour llite Sate 30˚ IBA TOSH 30˚ 15˚ 5M 1 2 1. Infrared Receiver Window 2. Remote Controller Operational range of the remote controller Even if within the effective scope as described above, the remote controller may malfunction or not work correctly in the following cases. ■ When an obstacle stands between the infrared receiver window of your computer and the remote controller. ■ When direct sunlight or strong fluorescent light strikes the infrared receiver window.
The Grand Tour Installing/Removing batteries Be sure to install the provided CR2016 type batteries before using the remote controller. The procedures for installing and removing the batteries vary depending on the type of the remote controller. Check the type and then install or remove the batteries as instructed. Store the battery for the remote controller beyond the reach of children. If a child swallows a battery, this might result in choking. If this happens, seek medical attention immediately.
The Grand Tour Installing the batteries 1. Open the battery cover on the back side of the remote controller. 1 1. Battery Cover Opening the battery cover 2. Be sure to place the batteries with correct polarities. Press the battery down to the stopper then push it forward to fit into the battery case. 1 2 1. Stopper 2. Battery Inserting the batteries 3. Close the battery cover. Press gently until it clicks into place.
The Grand Tour Slim size remote controller 1. Open the battery cover on the back side of the remote controller. 2. Hold down the stopper and slide the battery out of battery case. 1 2 1. Stopper 2. Battery Removing the batteries 3. Insert the battery in place. Be sure to place the batteries with correct polarities. Press the battery down to the stopper then push it forward to fit into the battery case. 4. Close the battery cover. Press gently until it clicks into place.
Getting Started Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ All users should be sure to read the section Starting up for the first time. ■ Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started 1. Connect the power cord to the AC adaptor. Connecting the power cord to the AC adaptor Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. 2. Connect the AC adaptor's DC output plug to the DC IN 19V jack on the right of the computer. Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet.
Getting Started Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Lift the panel up and adjust it to the best viewing angle for you. Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. Opening the display ■ When opening the panel, please be careful not to force it beyond the point where it moves easily.
Getting Started Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Windows setup. Press and hold the computer's power button for two or three seconds. IBA TOSH IBA TOSH llite Sate llite Sate Turning on the power Windows setup When you first turn on the power, the computer's initial screen is the Microsoft® Windows Startup Screen Logo.
Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Sleep Mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen. 1. If you have entered data, save it to the hard disk. 2. Make sure all disk (disc) activity has stopped, then remove the CD/ DVDs. ■ Make sure the Disk LED and ODD indicator are off.
Getting Started ■ When the AC adaptor is connected, the computer will go into Sleep Mode according to the settings in Power Options . ■ To restore operation from Sleep Mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup. ■ If the computer automatically enters Sleep Mode while a network application is active, the application might not be restored when the computer wakes up from Sleep Mode.
Getting Started ■ When the computer is shut down to Sleep Mode, the power indicator flashes orange. ■ If you are operating the computer on battery power, you can lengthen the operating time by turning it off to Hibernation Mode, as Sleep Mode consumes more power. Sleep Mode limitations Sleep Mode will not function under the following conditions: ■ Power is turned back on immediately after shutting down. ■ Memory circuits are exposed to static electricity or electrical noise.
Getting Started Automatic Hibernation Mode The computer will enter Hibernation mode automatically when you press the power button or close the Display Screen. First, however, make the appropriate settings according to the steps below. 1. Open the Control Panel. 2. Open System and Security and open Power Options. 3. Select Choose what the power button does. 4. Enable the desired Hibernation settings for When I press the power button and When I close the lid. 5. Click the Save changes button.
Getting Started System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes some tools to repair startup problems, run diagnostics or restore the system. You can see the more information about “Startup Repair” in “Windows Help and Support” content. The System Recovery Options can also be run manually to repair problems. The procedure is as follows. Follow the on-screen instructions. 1.
Getting Started Restoring the preinstalled software from the Recovery HDD Part of the space on the hard disk drive is reserved as recovery partition for restoring the pre-installed software from the hard disk drive. When re-setting up your hard disk, do not change, delete or add partitions in a manner other than specified in the manual. Otherwise, space for software may be destroyed.
Getting Started Restoring the preinstalled software from Recovery Media If the preinstalled files are damaged, use the Recovery Media you created, or HDD recovery to restore them. To restore the operating system and all preinstalled software, follow the steps below. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. 1. Load the Recovery Media in the optical media drive and turn off the computer's power. 2.
Operating Basics Chapter 4 Operating Basics This chapter gives information on basic operations including using the TouchPad, optical media drives, sound system, modem, the wireless LAN and LAN. It also provides tips on caring for your computer. Using the TouchPad To use the TouchPad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go. 1 IBA TOSH llite Sate 2 1. TouchPad 2.
Operating Basics Two buttons below the keyboard are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using. Do not press on the TouchPad too hard or press a sharp object such as a ball point pen against the TouchPad. The TouchPad could be damaged.
Operating Basics To use a Pinch Zoom gesture: 1. Place two fingers down on the TouchPad surface. 2. Slide the fingers further apart to zoom in or slide the fingers closer together to zoom out. For the best zooming experience, use the tips of your fingers. Rotating (ChiralRotate) The Rotating features provide convenient gestures for rotating photos and other objects. Momentum The Momentum feature delivers smooth, fast, trackball-like mouse movement.
Operating Basics How to swipe the finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: 1. Align the first joint of the finger to the center of the sensor. 2. While lightly touching the sensor, swipe the finger towards you until the sensor surface becomes visible. 3. Ensure the center of the fingerprint is on the sensor when swiping the finger.
Operating Basics Points to note about the fingerprint sensor Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) fingerprint recognition problems, or lower fingerprint rec-ognition success rate. ■ Do not scratch or poke the sensor with your nails or any hard or sharp objects. ■ Do not press too hard on the sensor. ■ Do not touch the sensor with a wet finger or any wet objects. Keep the sensor surface dry and free of water vapor.
Operating Basics ■ The fingerprint for each finger is different and unique. Please ensure that only the registered or enrolled fingerprint or fingerprints are used for identification. ■ Check sliding position and speed. ■ You can enroll up to 30~34 fingerprint data entries. ■ Fingerprint data is stored into the nonvolatile memory in the fingerprint sensor. Before you dispose of the computer, it is recommended that you delete the fingerprint data with the Delete menu of Fingerprint Software Management.
Operating Basics Points to note about the fingerprint utility ■ If the Windows file encryption function EFS (Encryption File System) is used to encrypt a file, the file cannot be further encrypted using the encryption function of this software. ■ You can back up the fingerprint data or the information registered to Password Bank. ■ Please use Import/Export menu on Fingerprint Software Management. ■ Please also refer to the fingerprint utility Help file for more information.
Operating Basics Windows logon via fingerprint authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows. This is especially useful when many users are using the computer, as user selection can be skipped. Fingerprint authentication procedure 1. Start up the computer. 2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor.
Operating Basics How to enable fingerprint system boot authentication settings It is necessary to first enroll your fingerprint with the TrueSuite Access Manager application prior to enabling and configuring the fingerprint Pre-OS feature. Check that your fingerprint is enrolled before configuring the settings. 1. Swipe your finger across the fingerprint sensor, or enter the Windows password and click Next. 2. Click settings. The Administrator Settings screen is displayed. 3.
Operating Basics Fingerprint utility limitations TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error-free. TOSHIBA does not guarantee that the fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
Operating Basics Metal paper clips or hair pins/clips will generate heat if they come into contact with USB ports. Do not allow USB ports to come into contact with metal products, such as when carrying the computer in your bag. Starting the USB Sleep and Charge Utility To start the utility, click Start Æ All Programs Æ TOSHIBA Æ Utilities Æ USB Sleep and Charge. Enabling USB Sleep and Charge This utility can be used to enable and disable the USB Sleep and Charge function.
Operating Basics Using the Web Camera This section describes the bundled webcam utility, which can capture still and video images. The web camera will auto-run when Windows starts. Please remove the protective plastic-film before using the Web Camera. 1 2 3 IBA TOSH llite Sate 1. Built-in microphone * 2. Web Camera Lens * 3.
Operating Basics Using the software The web camera software is pre-configured to start when you turn on Windows. To start it manually, go to Start Æ All Programs Æ Toshiba Æ Utilities Æ Web Camera Application. 1 2 3 4 5 6 8 7 1. Capture Still Images 2. Video Recording 3. Audio Recording 4. Function 5. Display Window 6. Camera resolution 7. Mute 8. Effects User’s Manual Capture Still Images Click to see a preview of the captured image. You can also e-mail the image.
Operating Basics Properties In the Options tab, flip or zoom the image, or set the flicker rate, night mode, and backlight compensation. In the Image tab, change the color settings. In the Profiles tab, change the lighting conditions. Settings In the Options tab, change the tool bar position. In the Picture tab, select picture output options such as size, export file and save path. In the Video tab, choose video output settings such as frame rate, size, record compressor, and save path.
Operating Basics ■ TOSHIBA Face Recognition does not guarantee the correct identification of a user. Changes to the likeness of a registrant, such as hair style changes, wearing a cap, or wearing glasses may effect the recognition rates. ■ TOSHIBA Face Recognition may incorrectly recognize faces that are similar to a registrant. ■ For high security purposes, TOSHIBA Face Recognition is not a suitable substitute for Windows passwords.
Operating Basics 3. Click Next to start the guide. 4. Take a picture while moving your neck slightly to the left and right. 5. Take a picture while moving your neck down and up. ■ Click the Back button to practice once more. 6. Click Next to start the image-capturing process. 7. Adjust the position of your face so that it fits within the face-shaped frame. Once your face has been positioned properly, the recording will commence. 8.
Operating Basics How to launch the help file For further information on this utility, please refer to help file. 1. Click Start Æ All Programs Æ TOSHIBA Æ Utilities Æ Face Recognition Help. Windows Logon via TOSHIBA Face Recognition This section explains how to logon to Windows with TOSHIBA Face Recognition. Two authentication modes are provided. ■ AUTO Mode Logon screen: If the face authentication file is selected by default, you can log on without using the keyboard or mouse.
Operating Basics Operation is the same for all optical media drives. The full-size drive provides high-performance execution of CD/DVD/BD-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVD/BDs without an adaptor. An ATAPI interface controller is used for CD/DVD/BD operation. When the computer is accessing a CD/DVD/BD, an indicator on the system glows. For precautions on writing to CD/DVD/BDs, refer to the Writing CD/DVD/ BDs section.
Operating Basics Pressing the eject button b. Pressing the eject button will not pop open the drawer when the disc drive's power is off. If the power is off, you can pop open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button. IBA TOSH llite Sate Manual release with the eject hole 2. Grasp the drawer gently and pull until it is fully opened.
Operating Basics Pulling the drawer open 3. Place the disc, label side up, in the drawer. IBA TOSH llite Sate Inserting a disc When the drawer is fully opened, the edge of the computer will extend slightly over the disc tray. Therefore, you will need to turn the disc at an angle when you place it in the tray. Once the disc is seated, make sure it lies flat, as shown in the figure above. ■ Do not touch the laser lens. Doing so could cause misalignment. ■ Keep foreign matter from entering the drive.
Operating Basics IBA TOSH llite Sate Closing the disc drawer ■ Slot ODD To load CD/DVD's, follow the steps as listed below and refer to following figures. 1. When the computer's power is on, insert CD/DVD into the ODD directly.
Operating Basics Removing discs ■ Tray ODD To remove the disc, follow the steps below and refer to the figure. Do not press the eject button while the computer is accessing the disc drive. Wait for the optical media drive indicator to go out before you open the drawer. Also, if the disc is spinning when you open the drawer, wait for it to stop before you remove it. 1. To pop open the drawer partially press the eject button. Gently pull the drawer out until it is fully opened.
Operating Basics 3. Push the center of the drawer to close it. Press gently until it locks into place. ■ Slot ODD To remove a CD/DVD, press eject button let the CD/DVD be put out. Writing CD/DVD/BDs ■ Some models in this series are equipped with Writing CD/DVD/BDs with the BD-R/RE drive. ■ Some models in this series are equipped with Writing CD/DVD with the BD Combo drive or DVD Super Multi drive. You can use the BD-R/RE drive to write data to CD-R-RW or DVD-R/-RW/ +R/+RW/-RAM or BD-R/-RE discs.
Operating Basics DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYO YUDEN Co.,Ltd. (for 8x and 16x speed media) DVD-R (Dual Layer): MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media) DVD-R for Labelflash: FUJIFILM CORPORATION (for 16x speed media) DVD+R: MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed media) DVD+R (Double Layer): MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.
Operating Basics Before writing or rewriting with the BD Combo drive ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R-RW and DVD-R/+R/-RW/+RW/-RAM discs. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., Ltd. MITSUBISHI KAGAKU MEDIA CO., LTD. Hitachi Maxell,Ltd. CD-RW: (Multi-Speed and High-Speed) MITSUBISHI KAGAKU MEDIA CO., LTD.
Operating Basics DVD+RW: MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x, 4x and 8x speed media) DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Panasonic Corporation (for 3x and 5x speed media) Hitachi Maxell,Ltd. (for 3x and 5x speed media) ■ BD Combo drive cannot use discs that allow writing faster than 8x speed (DVD-R, DVD+R and DVD+RW media), 6x speed (DVDRW media), 5x speed (DVD-RAM media), 4x speed, (DVD-R (Dual Layer) and DVD+R (Double Layer) media).
Operating Basics DVD+R: MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed media) TAIYO YUDEN CO., Ltd. (for 8x and 16x speed media) DVD+R (Double Layer): MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x and 8x speed media) DVD+R for Labelflash: FUJIFILM CORPORATION (for 16x speed media) DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 Victor Company of Japan, Ltd. (JVC) (for 2x, 4x and 6x speed media) MITSUBISHI KAGAKU MEDIA CO., LTD.
Operating Basics with a 2.6GB single-sided capacity and 5.2GB double-sided capacity. ■ Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-RW or DVD+R/+RW discs. ■ Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in whole or in part. ■ Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW or DVDRAM disc cannot be recovered. Check the content of the disc carefully before you delete it.
Operating Basics When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/ -RW, DVD-R/-RW/-RAM, DVD+R/+RW, or BD-R/-RE disc. ■ Do not perform any of the following actions when writing or rewriting: ■ ■ ■ ■ ■ ■ Change users in the Windows® 7 operating system. ■ Operate the computer for any other function, including using a mouse or TouchPad or closing/opening the LCD panel. ■ Start a communication application such as a modem.
Operating Basics Data Verification To verify that data has been written or rewritten correctly to a data CD/DVD, you should follow the steps below before you begin the write/rewrite process: 1. Display the setting dialog box by one of the following two steps: ■ Click Recording settings ( ) for writing on the main toolbar in the Data Disc mode. ■ Select Setting for Each Mode Æ Data Disc in the Setting menu. 2. Mark the Verify written data check box. 3. Select File Open or Full Compare mode. 4. Click OK.
Operating Basics 3. Add source from HDD by click Add Video files button to invoke browser dialog box. 4. Choose the source video then go to Next page to apply Menu. 5. After choose the menu template, press Next button to go to Burning Page. 6. Choose the output type then press Burn button. How to make a DVD-Video Simplified steps for making a DVD-Video from adding video source: 1. Click Start Æ All Programs Æ DVD MovieFactory for TOSHIBA Æ DVD MovieFactory Launcher to launch DVD MovieFactory. 2.
Operating Basics ■ While recording video to DVD, please close all other programs. ■ Do not run software like a screen saver because it can put a heavy load on the CPU. ■ Mp3 decoding and encoding are not supported. 2. Before recording the video to DVD ■ When you record DVD disc, please use only discs recommended by the Drive manufacturer. ■ Do not set the working drive to a slow device like a USB1.1 hard disk drive or it will fail to write DVD.
Operating Basics TOSHIBA DVD Player Please be aware of the following limitations when you use the TOSHIBA DVD PLAYER: Notes on use ■ Frame dropping, audio skipping or out of sync audio and video may occur during playback of some DVD Video titles. ■ Close all other applications when using the "TOSHIBA DVD PLAYER". Do not open or execute any other applications during DVD Video playback. Playback may stop or not function properly in some situations.
Operating Basics Display Devices & Audio 1. "TOSHIBA DVD PLAYER" will only run when "Colors" is set to "True Color (32 bit)". The "Colors" setting can be adjusted on the "Monitor" tab in the "Display Settings". To open the Display Settings, click Start Æ Control Panel Æ Appearance and Personalization / Appearance Æ Display Æ Change display settings Æ Advanced settings. 2.
Operating Basics Starting TOSHIBA DVD PLAYER Use the following procedure to start "TOSHIBA DVD PLAYER". 1. Insert a DVD-Video in the DVD Super Multi drive while Windows 7 is running. When an DVD-Video disc is set in the DVD drive, the following application selection screen may appear. If this occurs, select Play DVD movie, then click OK to launch the TOSHIBA DVD PLAYER. 2. Touch the CD/DVD panel on the Front operation panel. Or select Start Æ All Programs Æ TOSHIBA DVD PLAYER to start TOSHIBA DVD PLAYER.
Operating Basics ■ Playback of high bit rate content may cause frame dropping, audio skipping or decrease in computer performance. ■ Close all other applications before playing back Blu-ray Disc. Do not open any other applications or carry out any other operations during Blu-ray Disc playback. ■ Because Blu-ray Disc playback operates according to programs builtinto the content, operation methods, operation screens, sound effects, icons and other features may vary from disc to disc.
Operating Basics Starting WinDVD BD for TOSHIBA Use the following procedure to start "WinDVD BD for TOSHIBA". 1. When a Blu-ray disc is set in the BD drive, WinDVD BD for TOSHIBA starts automatically. 2. Touch the CD/DVD/BD button on the Front operation panel. Or select Start Æ All Programs Æ InterVideo WinDVD Æ WinDVD BD for TOSHIBA to start "WinDVD BD for TOSHIBA". Operating WinDVD BD for TOSHIBA Notes on Using "WinDVD BD for TOSHIBA". 1.
Operating Basics 6. If your CD/DVD/BD become dusty or dirty, wipe them with a clean dry cloth. Wipe from the centre out, not in a circular direction around the CD/DVD/BD. If necessary, use a cloth dampened in water or a neutral cleaner. Do not use benzine, thinner or similar cleaners. Modem Some models has a built in modem. This section describes how to connect and disconnect the internal modem to and from a telephone jack. The internal modem does not support voice functions.
Operating Basics Settings You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialling Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears, displaying location information for telephony.
Operating Basics TOSH IBA SATE GD Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected. Disconnecting To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. In the same way, pull the cable’s other connector out of the computer.
Operating Basics Using the FM tuner The availability of this feature depends on the model you purchased. 1. Plug the FM tuner antenna into the FM Antenna Jack. TOSH IBA 2 1 1. FM Antenna Jack 2. FM tuner antenna Installing the FM tuner 2. Select Start J All Programs J FM Tuner Utility to start FM software.
Operating Basics Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. ■ Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation.
Operating Basics Security ■ Be sure to enable the encryption function. Otherwise, you may expose your computer to illegal access by an outsider across the Wireless LAN, which may cause intrusion, eavesdropping, and the loss or destruction of stored data. TOSHIBA strongly recommends the customer to enable the encryption function. ■ TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof.
Operating Basics Wireless communication switch You can enable or disable the Wireless LAN function with the on/off switch. No transmissions are sent or received when the switch is off. Slide the Switch to turn it on and turn it off. Set the switch to off in airplanes and hospitals. Check the indicator. It will stop glowing when the wireless communication function is off. Wireless activity LED The wireless activity LED indicates the status of the wireless communication functions.
Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. 1. Turn off the power to the computer and to all external devices connected to the computer. 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. IBA TOSH lite Satel Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub.
Operating Basics Never spray cleaner directly onto the computer or let liquid run into any part of it. Never use harsh or caustic chemical products to clean the computer. ■ Remove the dust from the cooling vents on the backside of the computer regularly with a vacuum cleaner. Refer to Chapter 2, The Grand Tour, . Moving the computer The computer is designed for durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation.
Operating Basics The TOSHIBA HDD Protection function does not guarantee that the hard disk drive will not be damaged. When vibration is detected, a message will be displayed on the screen, and the icon in the Taskbar notification area will changed to the protection state. This message is displayed until the OK button is pressed or 30 seconds pass. When vibration subsides, the icon returns to the normal state. Taskbar icon State Icon Description Normal TOSHIBA HDD Protection is enabled.
Operating Basics 3D Viewer This feature displays a 3D object on the screen which moves in according to tilting or vibration of the computer. When the TOSHIBA HDD Protection detects computer vibration the Hard Disk Drive head is parked and the 3D object disk rotation will stop. When the head is un-parked the disk will begin to rotate again. The 3D Viewer can be started from the icon in the task tray. ■ This 3D object virtually represents the Computer's internal Hard Disk Drive.
The Keyboard Chapter 5 The Keyboard The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, function keys, soft keys, Windows special keys, and cursor control keys. Typewriter keys The typewriter keys produce the upper- and lower-case letters, numbers, punctuation marks, and special symbols that appear on the screen.
The Keyboard F1 ... F12 function keys The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Hot keys + Mute: Turns the volume on and off. + Lock: Enters "Lock computer" mode. To restore your desktop, you need to log on again. + Power plan: Displays the power save modes and lets you change the power settings. + Sleep: This hot key switches the system to Sleep Mode. + Hibernate: This hot key switches the system to Hibernate mode. + Output: Changes the active display device. Default resolution for simultaneous mode is set to 1024x768.
The Keyboard Wireless: Switches the active wireless devices if the wireless communication switch is switched on. + TouchPad: Enables or disables the Touch Pad function. + Zoom: Changes the display resolution. + TOSHIBA Zooming Utility (reduce): Reduces the icon size on the desktop or the font size within one of the supported application windows. + TOSHIBA Zooming Utility (enlarge): Increases the icon size on the desktop or the font size within one of the supported application windows.
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes.
Power and Power-Up Modes Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources, including charging the computer and battery tips for saving battery power, and power up modes.
Power and Power-Up Modes Table Power conditions Power on Universal AC adaptor not connected Power off (no operation) Battery charge is • Operates above low battery • LED: Battery off trigger point Battery charge is • Operates below low battery • LED: Battery flashes amber trigger point Battery charge is exhausted • Computer shuts down • LED: Battery off No Battery installed • Cannot operate • LED: Battery off Power indicators As shown in the above table, the Battery and Power indicators on the front
Power and Power-Up Modes White(Red) Indicates power is being supplied to the computer and the computer is turned on. Blinking amber Indicates power is being supplied to the computer while the computer is in Sleep Mode. The indicator turns on for one second and off for two seconds. No light Under any other conditions, the indicator does not light up. Battery types The computer has the following batteries: ■ Battery pack (6-cell or 12-cell depending on the model.
Power and Power-Up Modes Battery pack To ensure that the battery pack maintains its maximum capacity, operate the computer on battery power at least once a month until the battery pack is fully discharged. Refer to Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power through an AC adaptor for an extended period, more than a month, the battery may fail to retain a charge.
Power and Power-Up Modes The charge in the RTC battery is getting low or has been exhausted. You will need to set the date and time within the BIOS setup using the following steps: 1. Press F2 key - the BIOS setup screen will be displayed. 2. Set the date in System Date. 3. Set the time in System Time. 4. Press F10 key. A confirmation message will appear. 5. Press Enter key. BIOS setup will terminate and the computer will be rebooted.
Power and Power-Up Modes Care and use of the battery pack This section provides the important safety precautions in order to handle your battery pack properly. Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions. ■ Make sure the battery is securely installed in the computer before attempting to charge the battery pack. Improper installation could generate smoke or fire, or cause the battery pack to rupture.
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack (6-cell, 12-cell) 4-10 hours 4 hours max RTC battery About 24 hours About 24 hours The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored using the following methods. ■ Clicking the battery icon on the task bar ■ Via the Windows Mobility Center window ■ Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods. Battery pack (6-cell, 12-cell) Approximately 2 days (Sleep mode, 6-cell) Approximately 3.
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life, you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source.
Power and Power-Up Modes Installing the battery pack To install a battery, follow the steps below. ■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not touch the latch while holding the computer. If the latch is unintentionally released, you may get injured by the dropped battery. 1. 2. 3. 4.
Power and Power-Up Modes Starting the computer by password If you have already registered a password, there are two ways to start the computer: ■ Swipe your fingerprint on the sensor if you have already registered the fingerprint with the Fingerprint utility and enabled Fingerprint Poweron Security. If you would not like to swipe your finger or cannot authenticate the fingerprint for some reason, push the BACK SPACE key to skip the fingerprint authentication screen.
Power and Power-Up Modes Power-up modes The computer has the following power-up modes: ■ Boot Mode: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation Mode: Data in memory is saved to the hard disk. ■ Sleep Mode: Data is maintained in the computer's main memory. Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started.
HW Setup Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Password, Display, Boot Priority, Keyboard, LAN, and USB. Accessing HW Setup To run HW Setup, click , All Programs, TOSHIBA, Utilities, HWSetup. HW Setup Window The HW Setup window contains the following tabs: General, Password, Display, Boot Priority, Keyboard, USB and LAN .
HW Setup Password This tab allows you to set or reset the user password for power on. User Password Lets you register a new password or un-register an existing password. Not Registered Un-registers an existing password Registered Register a new password by following the on screen instructions Owner String This blank field is used to display a message when the password field is displayed on startup. If a password is not registered the message will not be shown. The maximum length is 256 characters.
HW Setup Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Sleep Mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in Sleep Mode. Enabled Enables the Wake-up on Keyboard function. Disabled Disables the Wake-up on Keyboard function (Default). USB USB Keyboard/Mouse/FDD Legacy Emulation Use this option to enable or disable Legacy USB support.
HW Setup SATA eSATA This feature allows you to set conditions of eSATA. Enabled Enables the eSATA port. (Default) Disabled Disables the eSATA port in order to save power. SATA Interface setting This feature allows you to set SATA interface setting. User’s Manual Performance Let HDD/SSD work with maximum performance. (Default) Battery life Let HDD/SSD work with battery life mode. If this setting is selected, this causes performance down.
Optional Devices Chapter 8 Optional Devices Optional devices can expand the computer's capabilities and its versatility.
Optional Devices ExpressCard The computer is equipped with an ExpressCard expansion slot that can accommodate two standard module formats: anExpressCard/34 module and an ExpressCard/54 module. An ExpressCard module is a small, modular add-in card technology based on PCI Express and Universal Serial Bus (USB) interfaces. Inserting an ExpressCard One ExpressCard connector is located on the left side of the computer.
Optional Devices Removing an ExpressCard ■ Before removing an ExpressCard, make sure that any applications or system services are not using the card. ■ Be sure to disable the ExpressCard prior to removing it. Otherwise, the system may be fatally damaged. To remove an ExpressCard, follow the steps below. 1. Click the Safely Remove Hardware icon on the Task Bar. 2. Click the ExpressCard you want to remove. 3. Press the ExpressCard once to eject it. 4. Grasp the ExpressCard and remove it.
Optional Devices SD/SDHC/MMC/MEMORY STICK / MEMORY STICK PRO/xD Memory cards The computer is equipped with a multiple digital media card slot that can accommodate SD/SDHC/MMC/MEMORY STICK/MEMORY STICK PRO/ xD memory cards. These memory cards allow you to easily transfer data from devices, such as digital cameras and Personal Digital Assistants, which use flash-memory.
Optional Devices Installing a memory card To install a memory card: 1. Insert the memory card. 2. Press gently to ensure a firm connection. Inserting a memory card Be sure the memory card is oriented properly before you insert it. If Windows fails to read the card, remove it then re-insert it. ■ The multiple digital media card slot only accepts one type of card at a time. Do not attempt to install more than one card as you risk damaging either the cards themselves or the computer.
Optional Devices ■ Make sure the memory card indicator is out before you remove the card or turn off the computer's power. If you remove the card or turn off the power while the computer is accessing the card, you may lose data or damage the card. ■ Do not remove the card while the computer is in Sleep or Hibernation mode. The computer could become unstable or data in the memory card could be lost.
Optional Devices Memory expansion You can install additional memory in the computer's memory module socket to increase the amount of RAM. This section describes how to install and remove a memory module. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost. a. The computer is turned on. b. The computer was shut down using the Sleep Mode or Hibernation Mode.
Optional Devices 1 1. Memory Module Cover Removing the memory module cover 6. Fit the module's connectors into the computer's connectors at about a 45 degree angle. Press the module carefully to ensure a firm connection. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Slot A is reserved for main memory. Use slot B for expanded memory. If only one card is installed, use slot A. 7. Push the module down so it lies flat.
Optional Devices 1 2 1. Slot A 2. Slot B Installing the memory module 8. Seat the cover and secure it with the screws. 9. Replace the battery pack as described in Chapter 6, Power and PowerUp Modes. 10. Turn the power on and make sure the added memory is recognized. Open System in the Control Panel and click the General tab. Points to note about memory module error If you install a memory module that is not compatible with the computer, the Power indicator will flash (on for 0.5 seconds, off for 0.
Optional Devices Removing a memory module Before removing the memory module, make sure the computer is in boot mode. To remove the memory module: 1. Be sure the power is off and all cables are disconnected from the computer. 2. Turn the computer upside down and remove the battery and the screws securing the memory module cover. 3. Slide your fingernail or a thin object under the cover and lift it off. 4. Push the latches outwards to release the module. A spring will force one end of the module up. 5.
Optional Devices 1 1. Latches Removing the memory module 6. Seat the cover and secure it with screws. Replace the battery pack. Additional battery pack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. Refer to Chapter 6, Power and Power-Up Modes.
Optional Devices External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. The hibernation and sleep feature can be used with an external monitor. Simply enable hibernation and sleep and the computer will maintain the data as it is displayed on the external monitor. 1. Turn the computer's power off. 2. Connect the monitor cable to the external monitor port. 3.
Optional Devices ■ When you connect a television or external monitor to the HDMI port and the display output device is set to HDMI. When you unplug the HDMI cable and re-plug it in please wait at least 5 seconds before you replug the HDMI cable again. ■ When you connect a television or external monitor to the HDMI port and you connect the television, external monitor or external sound device to another port. When you change the display output or Unplug/re-plug the HDMI cable.
Optional Devices Precautions 1. Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. 2. Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise. Data can be destroyed. 3.
Optional Devices 3. Disconnect the cable from the computer then from the i.LINK device. Refer also to the documentation that came with your i.LINK device.
Optional Devices eSATA (External Serial ATA) An eSATA device can be connected to the eSATA/USB combo port on the computer. Connecting an eSATA device To connect an eSATA device, follow the steps below: 1. Connect an eSATA cable to the eSATA/USB combo port. Make sure the connector is properly aligned with the socket. Do not try to force the connection. Doing so can damage the connecting pins.
Optional Devices Disconnecting an eSATA device When you have finished using an eSATA device, you can follow the procedures below in order to disconnect it: 1. Wait for the indicator light of an eSATA device to go out to make sure all activity has stopped. If you disconnect an eSATA device or turn off the power while the computer is accessing the drive, you may lose data or damage the eSATA device or the drive. 2. Click the Safely Remove Hardware icon on the Windows Taskbar. 3.
Troubleshooting Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on, it will recognize the new device.
Troubleshooting Software The problems may be caused by your software or disc. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the operating system documentation.
Troubleshooting Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: TOSHIBA Leading Innovation >>> This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the Battery indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t power the computer Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it.
Troubleshooting Problem Procedure Unplug the AC adaptor and remove the battery to make sure the terminals are clean. If necessary, wipe them with a soft dry cloth dipped in alcohol. Connect the AC adaptor and replace the battery. Make sure it is securely seated. Check the Battery indicator. If it does not light up, let the computer charge the battery for at least 20 minutes.
Troubleshooting ■ Reformatting the media ■ Reinstalling an operating system from the recovery CD-ROM The procedures above delete only the initial part of the data used for file management. This makes the file invisible to the operating system, but the data can still be read by specialized utilities. If you dispose of the PC, please delete all the data on its hard disk drive. Doing so prevents unauthorized use of such data.
Troubleshooting LCD panel Apparent LCD problems may be related to the computer's setup. Problem Procedure No display Press hot keys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Problems above remain Refer to your software’s documentation to unresolved or other determine if the software is causing the difficulty. problems occur Run the diagnostic test. Contact your dealer if the problems continue.
Troubleshooting Solid State drive Problem Procedure Computer does not boot There may be a problem with your operating system files. Refer to your operating system from hard disk drive documentation. Recovery Media Creator Problem Procedure The Recovery Media Creator can not be launched because there is no recovery partition. You will see this message if you have previously chosen to remove the partition and are trying to create "Recovery Media".
Troubleshooting BD drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive's drawer is securely closed. CD/DVD/BD in the drive Press gently until it clicks into place. Open the drawer and make sure the CD/DVD/BD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD/BD. Make sure there is no obstruction. Remove any foreign objects.
Troubleshooting Problem Procedure Some CD/DVD/BDs run The software or hardware configuration may be correctly, but others do causing a problem. Make sure the hardware configuration matches your software's needs. not Check the CD/DVD/BD documentation. Check the type of CD/DVD/BD you are using.
Troubleshooting Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. TouchPad Problem Procedure On-screen pointer does The system might be busy. If the pointer is not respond to Pad shaped as an hourglass, wait for it to return to its operation normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1.
Troubleshooting USB mouse Problem Procedure On-screen pointer does The system might be busy. If the pointer is not respond to mouse shaped as an hourglass, wait for it to resume its operation normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. To access this utility, click , Control Panel, Hardware and Sound, and the Mouse icon. 2.
Troubleshooting USB Sleep and Charge function Problem Procedure I cannot use the "USB Sleep and Charge function". The setting of "USB Sleep and Charge function" may be [Disabled]. Change the setting to [Enabled] in the TOSHIBA USB Sleep and Charge utility. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons. If this happens, disconnect the external device if one is connected.
Troubleshooting Problem Procedure External devices connected to the compatible ports do not work. Some external devices may not work when connected to a compatible port when the "USB Sleep and Charge function" is [Enabled] in the TOSHIBA USB Sleep and Charge Utility. Reconnect the external device after turning ON the computer.
Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on.
Troubleshooting Problem Procedure After making a call you Make sure the tone or pulse selection in your can’t hear a ring communications application is set correctly. You can also use the ATD command. Communication is cut off unexpectedly The computer will automatically cut off communication when connection with the carrier is not successful for a set time interval. Try lengthening this time interval.
Troubleshooting Fingerprint sensor Problem Procedure Reading of the fingerprint was not successful Please try again using the correct posture. Refer to Using the fingerprint sensor in Chapter 4, Operating Basics. Try the recognition process again using another enrolled finger. The fingerprint cannot be read due to injuries to the finger Try the recognition process again using another enrolled finger.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system. It is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below. User’s Manual Outside of Europe In Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division Building C, 12-24 Talavera Rd, North Ryde, 2113, NSW, Australia Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm8, D-41460 Neuss, Germany Canada TOSHIBA of Canada Ltd.
Specifications Appendix A Specifications This appendix summarizes the computer's technical specifications.
Specifications Communication specifications User’s Manual Communication System Data: Fax: Full duplex Half duplex Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax: ITU-T-Rec (Former CCITT) V.21/V.22/V.22bis/V.32/ V.32bis/V.34/V.90/V.92 103/212A V.17/V.29/V.27ter/V.21 ch2 Communication Speed Data transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/31200/ 33600 bps Data reception only with V.
Display Controller Appendix B Display Controller Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 16M colors. The display controller also controls the video mode, which uses industry standard rules to govern the screen resolution and the maximum number of colours that can be displayed on screen.
Wireless LAN Appendix C Wireless LAN Card Specifications Form Factor Mini PCI TypeIII Compatibility Wi-Fi ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The "Wi-Fi CERTIFIED" logo is a certification mark of the Wi-Fi Alliance. Network Operating System ■ Microsoft® Windows Networking Media Access Protocol ■ CSMA/CA (Collision Avoidance) with Acknowledgement (ACK) Data Rate ■ 54/48/36/24/18/12/9/6 Mb/s (IEEE 802.11a/g) ■ 11/5.
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Supported Frequency Sub-bands Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions. Wireless IEEE 802.11 Channels Sets (Revision B, G and N) Frequency Range Channel ID 2400-2483.
AC Power Cord and Connectors Appendix D AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Disclaimers Appendix E Disclaimers This chapter slates the Disclaimer(s) information applicable to TOSHIBA computers. CPU Central Processing Unit ("CPU") Performance Disclaimer.
Disclaimers Contact Toshiba Technical Service and Support for more information. 64-Bit Computing 64-bit processors are designed to take advantage of 32 and 64 bit computing.
Disclaimers HDD drive capacity One Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as Microsoft Operating System and/or pre-installed software applications, or media content.
Disclaimers External HDD Capacity One Gigabyte (GB) means 109 =1,000,000,000 bytes using powers of 10. A computer operating system, however, reports storage capacity using powers of 2 for the definition of 1GB=230=1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the computer includes one or more pre-installed operating systems, pre-installed software applications, or media content. Actual formatted capacity may vary.
TOSHIBA PC Health Monitor Appendix F TOSHIBA PC Health Monitor The TOSHIBA Health Monitor software program monitors computer system functions such as power consumption, the cooling system and HDD Drop sensor. It alerts users of specific system conditions via pop-up messages. It also tracks the usages of the computer and related devices, logging the service relevant information on the computer's hard disk drive.
TOSHIBA PC Health Monitor TOSHIBA's standard limited warranty terms and limitations apply. Visit http://www.warranty.toshiba.com for details. Starting the TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor can be started using the following methods: ■ Double click TOSHIBA PC Health Monitor in the Welcome Center. ■ Click Start Æ All Programs Æ TOSHIBA Æ Utilities Æ PC Health Monitor. ■ Click the icon in the notification area, then click the "TOSHIBA PC Health Monitor is not enabled.
Glossary Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary HDD: hard disk drive HDCP: high-bandwidth digital content protection HDMI: high definition multimedia interface HDMI-CEC: high definition multimedia interface consumer electronics control IDE: integrated drive electronics IEEE: Institute of Electrical and Electronics Engineers IMSM: Intel Matrix Storage Manager I/O: input/output IRQ: interrupt request KB: kilobyte LAN: local area network LCD: liquid crystal display LED: light emitting diode MB: megabyte MMC: multi media card OCR: optical character
Glossary A adaptor: A device that provides a compatible connection between two units. For example, the computer's internal display adapter receives information from the software and translates it into images on the screen. An adapter can take a number of forms, from a microprocessor to a simple connector: An intelligent adapter (one that is capable of doing some processing) may also be called a controller.
Glossary bootable disk: See system disk. bps: Bits per second. Typically used to describe the data transmission speed of a modem. buffer: The portion of the computer's memory where data is temporarily stored. Buffers often compensate for differences in the rate of flow from one device to another. bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character.
Glossary COM1, COM2, COM3 and COM4: The names assigned to the serial and communication ports. commands: Instructions you enter at the terminal keyboard that direct the actions of the computer or its peripheral devices. compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Glossary device driver: A program (called a "driver") that permits a computer to communicate with a device. dialog box: A window that accepts user input to make system settings or record other information. disable: To turn a computer option off. See also enable. disk drive: The device that randomly accesses information on a disk and copies it to the computer's memory. It also writes data from memory to the disk.
Glossary erase: See delete. escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems. 2) A means of aborting the task currently in progress. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. execute: To interpret and execute an instruction.
Glossary H hard disk: A storage device composed of a rigid platter or platters that can be magnetically coded with data. Hard disks hold much more information than diskettes and are used for long-term storage of programs and data. The primary (or only) hard disk in a computer is usually fixed, but some computers have secondary hard disks that are removable. By default, the hard disk is referred to as drive C. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk.
Glossary K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer. For each key, the transmitted code is, in turn, representative of the (ASCII) character marked on the key. kilobyte (KB): A unit of data storage equal to 1024 bytes.
Glossary M main board: See motherboard. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. memory: Typically refers to the computer's main memory, where programs are run and data is temporarily stored and processed. Memory can be volatile and hold data temporarily, such as RAM, or it can be nonvolatile and hold data permanently, such as ROM. A computer's main memory is RAM.
Glossary O OCR: Optical Character Recognition (reader). A technique or device that uses laser or visible light to identify characters and input them into a storage device. online state: A functional state of a peripheral device when it is ready to receive or transmit data. operating system: A group of programs that controls the basic operation of a computer.
Glossary port: The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver: A TOSHIBA utility that lets you set the parameters for various power-saving functions. program: A set of instructions a computer can execute that enables it to achieve a desired result. See also application. prompt: A message the computer provides indicating it is ready for or requires information or an action from you.
Glossary S S/P DIF: A standard of digital interface for audio. SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. SD/SDHC Card: Secure Digital cards are flash memory widely used in a variety of digital devices such as digital cameras and Personal Digital Assistants. serial: Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel.
Glossary V VGA: Video Graphics Array is an industry standard video adaptor that lets you run any popular software. volatile memory: Random access memory (RAM) that stores information as long as power is supplied to the computer. W warm start: Restarting or resetting a computer without turning it off.
Index Index A AC adaptor, 1-5 additional, 1-19 connecting, 3-2 ASCII characters, 5-5 B Battery charging, 6-6 extending battery life, 6-9 indicator, 6-1 Monitoring capacity, 6-8 real time clock, 1-5, 6-4 save mode, 1-13 types, 6-3 Battery pack, 1-5 additional, 8-11 replacing, 6-10 C Cleaning the computer, 4-45 D Display, 1-9 automatic power off, 1-13 brightness decreases, 5-3 brightness increases, 5-3 controller, 1-9 opening, 3-4 E Express card inserting, 8-2 removing, 8-3 Expresscard, 8-2 F Floppy di
Index K Keyboard, 1-9, 5-1 emulating keys on enhanced, 5-2 F1 ...
Index Sleep Mode, 1-14 setting, 3-6 System automatic, 1-13 Soft keys emulating keys on enhanced keyboard, 5-2 ScrLock, 5-2 Sound System, 1-10 Headphone(S/P DIF) jack, 1-11 microphone jack, 1-11 mute hot keys, 5-3 T TOSHIBA ConfigFree, 1-18 Touch Pad, 1-9 using, 4-1 U USB, 1-10 V Video RAM, 1-4 W Wireless communication switch, 4-44 indicator, 4-44 Wireless LAN, 1-11 using, 4-42 User’s Manual Index-3
