POWER AMPLIFIER 使用说明书 ZH
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
注意事项 请在操作使用前,首先仔细阅读下述内容 * 请将本说明书存放在安全的地方,以便将来随时参阅。 警告 为了避免因触电、短路、损伤、火灾或其它危险可能导致的严重受伤甚至死亡,请务必遵守下列基本注意事 项。这些注意事项包括但不限于下列情况: 电源 / 电源线 关于潮湿的警告 • 只能使用本设备所规定的额定电压。所要求的电压被印在本设 备的铭牌上。 • 请勿让本设备淋雨或在水附近及潮湿环境中使用,或将盛有液 体的容器放在其上,否则可能会导致液体溅入任何开口。 • 只能使用提供的电源线。 • 切勿用湿手插拔电源线插头。 • 请勿将电源线放在热源如加热器或散热器附近,不要过分弯折 或损伤电源线,不要在其上加压重物,不要将其放在可能被踩 踏引起绊倒或可能被碾压的地方。 当意识到任何情况时 • 若电源线出现磨损或损坏,使用设备过程中声音突然中断或因 此而发出异常气味或冒烟,请立即关闭电源开关,从电源插座 中拔出电源线插头,并请有资格的 YAMAHA 维修人员对设备 进行检修。 • 请务必连接到带有保护接地连接的适当电源插座。接地不当可 能引起触电。 请勿打开 • 若本设备发生摔落或损坏,请立即关
小心操作 • 打开音频系统的交流电源时,请始终最后打开本设备,以避免 损坏音箱。同样,关闭电源时,请首先关闭本设备。 • 请勿将手指或手插入本设备的任何间隙或开口 ( 通风口等 )。 • 请避免在设备上的任何间隙或开口 ( 通风口等 ) 插入或落进异物 ( 纸张、塑料、金属等 )。万一发生这种情况,请立即关闭电源 开关,从 AC 电源插座中拔出电源插头。然后请有资格的 YAMAHA 维修人员进行检修。 • 请勿长时间持续在很高或不舒服的音量水平使用本设备,否则 可能会造成永久性听力损害。若发生任何听力损害或耳鸣,请 去看医生。 • 请勿将身体压在本设备上或在其上放置重物,操作按钮、开关 或插口时要避免过分用力。 • 请勿将本设备用于带动扩音器以外的其他目的。 对由于不正当使用或擅自改造本设备所造成的损失、数据丢失或破坏, YAMAHA 不负任何责任。 当不使用本设备时,请务必关闭其电源。 即使电源开关被置于 “STANDBY”( 待机 ) 位置,设备中仍有微量的电流。当确定长时间不使用本设备时,请务必将 AC 电源插头从 AC 电 源插座拔出。 经常动态接触的零部件,如开关、控制旋钮、接口等,随着时间的推
前言 感谢您购买 YAMAHA XP7000、 XP5000、 XP3500、 XP2500、 XP1000 系列功率放大器。 XP 系列功率放大器是根据 YAMAHA 在功率放大设备制造方面的丰富经验并通过始终如一 的精心路线设计开发而成。采用了 EEEngine ( 能源效率引擎 ) 技术,以上功率放大器的特 点是功率大、质量优、可靠性高、稳定性好,保证达到最高音频特性。 主要特点是: • 提供了三种模式供各种应用程序使用:由两个单独声源驱动的 STEREO 模式,由单个声源驱动 两个通道的 PARALLEL 模式,以及由两个内置放大器共同工作等同于一个大功率单声道放大器 的 BRIDGE 模式。 • 具有平衡式 XLR 连接头和 Euroblock 连接头输入, Speakon 连接头和 5 路接线柱输出。 • 能够选择截止频率 (20Hz 或 55Hz) 的高通过滤器开关。 • 每个通道具有 SIGNAL 指示灯、 CLIP 指示灯和高精 dB 音量控制。 • 显示各种保护系统状态 ( 电源开 / 关检测、输出保护、 DC 检测 ) 的 PROTECTION 指示灯,显示 散热器过热的 TEMP 指示
各控制钮和功能 ■ 前面板 2 7 1 4 3 5 6 7 * 图中所示为 XP7000 型功率放大器。 1 POWER 开关及指示灯 按 该 开 关 可 打 开 或 关 闭 电 源。当 电 源 打 开 后 POWER/STANDBY指示灯亮绿灯。如果功率放大器 被设定为 STANDBY 模式,指示灯亮黄灯。 2 TEMP 指示灯 若散热器温度超过 85°C (185°F),该指示灯亮红灯。 3 PROTECTION 指示灯 保护系统处于活动状态时, PROTECT 指示灯亮红 灯,音箱自动从放大器输出端断开连接。在以下情 况下保护系统启动: 放大器打开时 放大器打开时,保护系统启动大约 3 秒钟。3 秒 钟后,保护系统自动关闭,放大器准备开始正常 工作。 5 SIGNAL 指示灯 当相应声道的输出电平超过 2 Vrms ( 相当于 8 负 荷上的 1/2 W 或 4 负荷上的 1 W)。 6 VOLUME 控制旋钮 每个控制旋钮用来分 31 档在 - ∞ dB 至 0 dB 的范围 内调节相应通道的音量。 * 若想锁定旋钮设置,可固定附带在旋钮上的保护盖, 这样有关设置就
■ 后面板 4 3 1 5 2 1 XLR 输入连接头 7 8 5 MODE 开关 这些平衡式 XLR-3-31 型连接头用于连接输入信号。 针脚如下图所示 (IEC 60268)。 热线 7 6 地线 冷线 * 在 BRIDGED 模式下,每对通道只有第一个通道是打 开的,即 A/B 通道对的 A 通道。切勿将音频信号输入 到处于非活动状态的输入端子。 2 Euroblock 连接头 • STEREO 模式 在 STEREO 模式下,通道 A 和 B 是完全独立的。 • PARALLEL 模式 在 PARALLEL 模式下,通道 A 的输入信号同时 被发送到通道 A 的功率放大器和通道 B 的功率放 大器。在这种情况下,负载自动在 A 输入端子和 B 输入端子之间连接。 • BRIDGED 模式 在 BRIDGED 模式下,通道 A 和通道 B 同时工 作,相当于一台单声道放大器。 注: 如果在 PARALLEL 和 BRIDGED 模式下,输 入端子 A 和 B 会自动短接。切勿将音频信号输 入到处于非活动状态的输入端子。 这些平衡式 Euroblock 连接头用于连
音箱的连接 如下图所示,可以采用三种方法连接音箱。请注意,音箱的阻抗随连接方式和连接的音箱数量不同而变化。请务 必保证音箱的阻抗不低于下图所示的最低值。 ■ STEREO 模式 将 MODE 开关设为 STEREO,将本机用作立体声放大器。使用前面板上的音量控制旋钮 (A 和 B)可以单独控制 各通道的音量。 ● 5 路接线柱 ● Speakon 连接插口 – + + 4* – 4* 4* * 最低音箱阻抗 4* * 最低音箱阻抗 ■ PARALLEL 模式 将 MODE 开关设为 PARALLEL,将本机用作双通道单声道放大器。使用前面板上的音量控制旋钮 (A 和 B)可 以单独控制各通道的音量。 注: 在这种情况下,放大器上 A 和 B 的负载被直接连接。切勿将信号输入 B 端子。 ● 5 路接线柱 ● Speakon 连接插口 – + 4* + – 4* * 最低音箱阻抗 8 XP7000/XP5000/XP3500/XP2500/XP1000 使用说明书 4* 4* * 最低音箱阻抗
■ BRIDGED 模式 (作为大功率单声道放大器使用时) 将 MODE 开关设为 BRIDGED,将本机用作大功率单声道放大器。使用前面板 A 上的音量控制旋钮 A 可控制音量。 注: 在这种情况下,放大器上 A 和 B 的负载被直接连接。 切勿将信号输入 B 端子。 ● 5 路接线柱 ● Speakon 连接插口 – + 最低音箱阻抗 : 8 最低音箱阻抗 : 8 XP7000/XP5000/XP3500/XP2500/XP1000 使用说明书 9
高阻抗音箱的连接 (仅适用于 XP7000/3500) XP7000 可与多个支持 70V 线路输出的高阻抗音箱以 STEREO 或 PARALLEL 方式连接。 可以连接的音箱数随音箱额定输入功率的不同而变化。可以连接音箱的每通道最大总额定输入功率为 625 W。 例如,如果使用额定输入功率为 10 W 和 15 W 的音箱,设为 10 W 时最多可以连接 31 个音箱 ( 相当于 310 W),设 为 15 W 时最多可以连接 21 个音箱 ( 相当于 315 W)。总计为每通道 625 W。 务必使用支持 XP7000 线路输出电压为 70V 的音箱。 或 1 21 1 31 15W 15W 10W 10W 15W × 21 个音箱 (315W) 1 31 1 10W 10W × 31 个音箱 (310W) 10W 15W 10W × 31 个音箱 (310W) 音箱的总额定输入功率: 625 W ( 最大 ) 21 15W 15W × 21 个音箱 (315W) 音箱的总额定输入功率: 625 W ( 最大 ) XP3500 可与多个支持 100V 线路
连接 ■ 使用 Euroblock 连接头 使用螺丝刀 固定导线。 如果连接线需要频繁地连接和断开,如便携安装 用途,我们建议您使用带有绝缘环的金属套箍。 使用的套箍导电部分外径应为 1.
故障排除 下表列出了工作异常的主要原因和处理措施,以及每种情况下的保护电路的动作。 指示灯 可能原因 处理措施 某扬声器端子、放大器端子或电 线出现短路。 找到短路位置,排除短路原因。 放大器超负荷。 请使用阻抗至少为 4Ω(STEREO/ PARALLEL 模式 ) 或 8Ω (BRIDGE 模式 ) 的音箱系统。 TEMP 指示灯亮灯。 散热器温度超过 85°C (185°F)。 检查通风槽,使放大器周围保持 更畅通的空气流动。 TEMP 指示灯亮灯,指示 温度警告。 PROTECTION 指示灯 亮灯。 散热器温度超过 90°C (194°F)。 检查放大器的通风条件,采取适当 措施改善放大器周围的空气流动。 热保护电路动作,保护功 放晶体管。 处理措施 保护电路 CLIP 指示灯亮灯。 保护电路 PC 限制器电路动作,保 护功放晶体管。 ● XP3500、 XP2500 指示灯 可能原因 PROTECTION 指示灯 亮灯。 功率放大器输出电路产生了 +2 V/ -2 V 或更大的 DC 电压。 请向代理经销商或就近的 YAMAHA 维修服务中心咨询。
Specifications ■ General Specifications XP7000 Output Power 1 kHz THD+N= 1 % 20 –20 kHz THD+N= 0.1 % 1 kHz 20mS nonclip SN Ratio Power Consumption 20Hz-20kHz Standby / Idle 1/8 (4 /Pink noise) 8/STEREO 4 /STEREO 8 /BRIDGED 8 /STEREO 4 /STEREO 70 V/STEREO RL=8 8 /BRIDGED 2 /STEREO 4 /BRIDGED (DIN AUDIO) MIN 1 kHz THD+N= 1 % 20 –20 kHz THD+N= 0.
All Models Power Bandwidth THD+N Intermoduration Distortion Frequency Response Half Power, THD+N= 0.5 % 20 Hz–20 kHz, Half Power 60 Hz:7 kHz, 4:1, Half Power RL=8 Ω, Po=1 W, HPF=OFF 20 Hz-50 kHz Channel Separation Half Power, RL=8 Ω, 1 kHz, Att. max, input 600 Ω shunt 20 Hz–20 kHz, Att. min, (DIN AUDIO) RL=8 Ω, 1 kHz Att. max Residual Noise Damping Factor Voltage Gain MIN MAX MAX MAX TYP MIN 10 Hz-40 kHz 0.1 % 0.
■ MONITOR/REMOTE PIN layout Pin No. 1 2 3 Signal GND REMOTE CONTROL MONITOR 4 5 6 7 REMOTE CONTROL 8 9 10 11 12 13 14 15 MONITOR Description STANDBY MODEL ID STANDBY Control: Supply 5 VDC, 5 mADC XP7000: 1.0 k, XP5000: 1.2 k, XP3500: 1.5 k, XP2500: 1.8 k, XP1000: 2.2 k (Impedance to GND) NC NC MUTE CH B MUTE CH A MUTE On Control: Connect to GND (max.
XP7000/XP5000/XP3500/XP2500/XP1000 使用说明书 – + G – + G 3 2 LINE FILTER XLR 1 Euroblock FG CH B [+22dBu MAX] INPUT CH A 3 2 XLR 1 +24 RELAY DRIVE CIRCUIT RELAY POWER SW GR/OR (GR+RE) POWER/STANDBY PARALLEL BRIDGE STEREO PARALLEL BRIDGE STEREO CH B ATT CH A ATT U, A destination J, H destination Thermal cutoff SUB TRANS PO SBY LED DRIVE CIRCUIT HA HA MODE BA BA HPF 55Hz OFF 55Hz TEMPERATURE SENSOR OVERCURRENT DETECT CIRCUIT DRIVER LATCH CIRCUIT LIMITER PA P
– + G – + G 3 2 XLR 1 FG Except J destination PARALLEL BRIDGE STEREO PARALLEL BRIDGE STEREO POWER/STANDBY POWER SW GR/OR (GR+RE) J destination only CH B 2 3 Euroblock [+22dBu MAX] INPUT CH A 1 XLR RELAY 2 Thermal cutoff BA BA RELAY & LED DRIVE CIRCUIT MODE CH B ATT CH A ATT RELAY 1 SUB TRANS HA HA PO SBY HPF 55Hz OFF 55Hz 55Hz Thermal Thermal cutoff protector MAIN TRANS HPF 55Hz HPF 20Hz 20Hz HPF 12dB/oct 130˚C +4dBu +26dB +32dB GAIN +4dBu +26dB +32dB O
■ Current Draw XP7000 Line Current (A) 100/120V Power (W) 230/240V In Out Thermal Dissipation Dissipated Btu/h kcal/h standby 0.08 0.04 5 0 5 17 4 idle 1.0 0.5 35 0 35 119 30 1/8 power 1/3 power 8/ch 5.4 3.0 379 188 191 653 165 4/ch 8.5 4.7 611 275 336 1150 289 8/ch 12.8 7.0 918 500 418 1430 360 4/ch 20.6 11.
ӝѣᴿᇩ⢟䍞Ⲻ〦䠅 ᴿᇩ⢟䍞 䜞Ԭ〦 䫵˄Pb˅ ⊎˄Hg˅ 䭹˄Cd˅ ঠࡧ㓯䐟ᶯ ޝԧ䬜˄Cr (VI)˅ ཊⓤ㚄㤟 ˄PBB˅ ཊⓤҼ㤟䟊 ˄PBDE˅ h ƻ ƻ ƻ ƻ ƻ h ƻ h ƻ ƻ ƻ ᵜ㺘Ṭ ᦞSJ/T 11364 Ⲵ㿴ᇊ㕆ࡦDŽ ƻ˖㺘⽪䈕ᴹᇣ⢙䍘൘䈕䜘Ԧᡰᴹ൷䍘ᶀᯉѝⲴਜ਼䟿൷൘ GB/T 26572 㿴ᇊⲴ䲀䟿㾱≲ԕлDŽ h˖㺘⽪䈕ᴹᇣ⢙䍘㠣ቁ൘䈕䜘ԦⲴḀа൷䍘ᶀᯉѝⲴਜ਼䟿䎵ࠪ GB/T 26572 㿴ᇊⲴ䲀䟿㾱≲DŽ ↚ḽ䇼䘸⭞ӄ൞ѣӰ≇ާૂള䬶Ⲻ⭫ᆆؗᚥӝȾ ḽ䇼ѣ䰪ⲺᮦᆍѰ⧥ֵؓ⭞ᵕ䲆ⲺᒪᮦȾ ؍ᣔ⧟ຳ ྲ᷌䴰㾱ᓏᔳ䇮༷ᰦˈ䈧оᵜൠޣᵪᶴ㚄㌫ˈ㧧ਆ↓⺞Ⲵᓏᔳᯩ⌅DŽ 䈧यሶ䇮༷䲿ђᔳᡆѪ⭏⍫ඳ൮༴⨶DŽ
雅马哈乐器音响(中国)投资有限公司 上海市静安区新闸路1818号云和大厦2楼 客户服务热线:4000517700 公司网址:http://www.yamaha.com.cn 制造商:雅马哈株式会社 制造商地址:日本静冈县滨松市中区中泽町10-1 进口商:雅马哈乐器音响(中国)投资有限公司 进口商地址:上海市静安区新闸路1818号云和大厦2楼 原产地:印度尼西亚 Yamaha Pro Audio global website http://www.yamahaproaudio.com/ Yamaha Downloads http://download.yamaha.com/ Manual Development Department © 2005 Yamaha Corporation 2015年12月 改版 MWAPx.