User Manual

MOTIF XF Data List
100
Effect Parameter List
[6] SLICE
[7] TECH MODULATION
Category — MISC
[1] VCM EQ 501
[2] HARMONIC ENHANCER
[3] Talking Modulator
[4] DAMPER RESONANCE
[5] PITCH CHANGE
[6] EARLY REFLECTION
No. Parameter Range Value Table N o.
1 Divide Type 16th – 4th (5 – 11) 14
2 Gate Time 0 – 100% (0 – 100)
3 Pan AEG Type A – E (0 – 4)
4 Pan AEG Min Level 0 – 127 (0 – 127)
5 Pan Depth -63 –+63 (1 – 127)
6 Divide Min Level 0 – 127 (0 – 127)
7 Pan Type A – J (0 – 9)
8 Overdrive 0 – 127 (0 – 127)
9 AEG Phase 0 – 15 (x 16th note) (0 – 15)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 94.
No. Parameter Range Value Table N o.
1 Mod Speed 0 – 127 (0 – 127)
2 Mod Depth 0 – 127 (0 – 127)
3 Mod Gain -12 – +12dB (52 – 76)
4 Mod Mix Balance D63>W – D=W – D<W63 (1 – 127)
5 Pre Mod HPF Cutoff
Frequency
20Hz – 8.0kHz (0 – 52) 3
6 Mod LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
7 Mod LPF Resonance 1.0 – 12.0 (10 – 120)
8 Delay Time 0.1 – 740.0ms (1 – 7400)
9 Delay Time Ofst R 0 – 884 (0 – 884)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Feedback Level -63 – +63 (1 – 127)
12 FB Level Ofst R -63 – +63 (1 – 127)
13 Feedback Hi Damp 0.1 – 1.0 (1 – 10)
14 FB Hi Damp Ofst R -0.9 – +0.9 (1 – 19)
15 —
16 —
No. Parameter Range Value Table N o.
1 EQ1 (LSH) Frequency 31.5Hz – 2.0kHz (12 – 84) 30
2 EQ1 (LSH) Gain -12.0dB – +12.0dB (60 – 300)
3 EQ2 Q 0.50 – 16.00 (0 – 60) 31
4 EQ2 Frequency 50.0 Hz – 20.0kHz (20 – 124) 30
5 EQ2 Gain -18.0dB – +18.0dB (0 – 360)
6 EQ3 Q 0.50 – 16.00 (0 – 60) 31
7 EQ3 Frequency 50.0 Hz – 20.0kHz (20 – 124) 30
8 EQ3 Gain -18.0dB – +18.0dB (0 – 360)
9 EQ4 Q 0.50 – 16.00 (0 – 60) 31
10 EQ4 Frequency 50.0 Hz – 20.0kHz (20 – 124) 30
11 EQ4 Gain -18.0dB – +18.0dB (0 – 360)
12 EQ5 (HSH) Frequency 500Hz – 20.0kHz (60 – 124) 30
13 EQ5 (HSH) Gain -12.0dB – +12.0dB (60 – 300)
14 Output Level -12.0dB – +12.0dB (60 – 300)
15
16
No. Parameter Range Value Table N o.
1 HPF Cutoff Frequency 500Hz – 16.0kHz (28 – 58) 3
2 Overdrive 0 – 127 (0 – 127)
3 Mix Level 0 – 127 (0 – 127)
4—
5—
6—
7—
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No.
1 Vowel a/i/u/e/o (0 – 4)
2 Move Speed 1 – 62 (1 – 62)
3 Overdrive 0 – 127 (0 – 127)
4 Output Level 0 – 127 (0 – 127)
5—
6—
7—
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No.
1 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
2 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
3 EQ Low Frequency 32Hz – 2.0kHz (4 – 40) 3
4 EQ Low Gain -12 – +12dB (52 – 76)
5 Hi Resonance 0.1 – 1.0 (1 – 10)
6 Pedal Response slow/normal/fast (0 – 2)
7—
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 —
14 —
15 —
16 Damper Control 0 – 127 (0 – 127)
No. Parameter Range Value Table No.
1 Pitch 1 -24 – +24 (40 – 88)
2 Fine 1 -50 – +50 (14 – 114)
3 Initial Delay 1 0.1ms – 400.0ms (0 – 127) 7
4 Feedback Level 1 -63 – +63 (1 – 127)
5 Pitch 2 -24 – +24 (40 – 88)
6 Fine 2 -50 – +50 (14 – 114)
7 Initial Delay 2 0.1ms – 400.0ms (0 – 127) 7
8 Feedback Level 2 -63 – +63 (1 – 127)
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Pan 1 L63 – C – R63 (1 – 127)
12 Output Level 1 0 – 127 (0 – 127)
13 Pan 2 L63 – C – R63 (1 – 127)
14 Output Level 2 0 – 127 (0 – 127)
15 —
16 —
No. Parameter Range Value Table No.
1 Type S-hall, L-hall, random,
reverse, plate, spring
(0 – 5)
2 Room Size 0.1 – 20.0 (0 – 127) 6
3 Diffusion 0 – 10 (0 – 10)
4 Initial Delay 0.1ms – 200.0ms (0 – 127) 5
5 Feedback Level -63 – +63 (1 – 127)
6 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
7 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Liveness 0 – 10 (0 – 10)
12 Density 0 – 3 (0 – 3)
13 Feedback High Damp 0.1 – 1.0 (1 – 10)
14 —
15 —
16 —