User Manual

set
get
Notify
setn
getn
Notify
gett min max default scaling unit R/W remarks
No.
Command
Parameter
Address
Sub Address
x
y
Case
Target Parameters
62
Mode ✔ ✔ ✔
PCD:InRedundancy/Mode
0 0 1 0 index R/W 0: BACKUP
1: OVERRIDE
63
Auto Return
✔ ✔ ✔
PCD:InRedundancy/AutoReturn
0
1
0 index R/W 0:OFF
1:ON
64
ON ✔ ✔ ✔
PCD:InRedundancy/Second/On
0 0 1 0 index R/W 0:OFF
1:ON
65
Override
Threshold
✔ ✔ ✔
PCD:InRedundancy/Second/
OvrThresh
-800 0 0
x10 dBFS R/W
-800: -80.0dBFS
:
0: 0.0dBFS
66
Override
Return
Delay
✔ ✔ ✔
PCD:InRedundancy/Second/Ovr
ARDelay
0 60 10
x1 sec R/W 0: 0sec
:
60: 60sec
67
ON ✔ ✔ ✔
PCD:InRedundancy/Third/On
0
1
0 index R/W 0:OFF
1:ON
68
Override
Threshold
✔ ✔ ✔
PCD:InRedundancy/Third/OvrTh
resh
-800 0 0
x10 dBFS R/W
-800: -80.0dBFS
:
0: 0.0dBFS
69
Override
Return
Delay
✔ ✔ ✔
PCD:InRedundancy/Third/OvrAR
Delay
0 60 10
x1 sec R/W 0: 0s
:
60: 60s
70
Redundancy
Status
✔ ✔ ✔
PCD:InRedundancy/Status
0
2 0 index R
0: NORMAL
1: SECOND STATE
2: THIRD STATE
71
On
✔ ✔ ✔
PCD:AmpCh/LoadMon/On
0 1
0
index R/W 0:OFF
1:ON
72
OSC ON ✔ ✔ ✔
PCD:AmpCh/LoadMon/Osc/On
0 1 0 index R/W 0:OFF
1:ON
73
OSC Level ✔
✔
✔
PCD:AmpCh/LoadMon/Osc/Level
0 10 0.0 index
Vrms
R/W
* refer "OSC Level" table
74
Detect Freq
✔ ✔ ✔
PCD:AmpCh/LoadMon/Freq
237 250
248
index Hz R/W
237: 14.5kHz
:
248: 20.0kHz
:
250: 21.2kHz
75
High
Threshold
✔ ✔ ✔
PCD:AmpCh/LoadMon/HighThre
sh
0 500 500
x10 ohm R/W
0: 0.0 (ohm)
:
500: 50.0 (ohm)
76
Low
Threshold
✔ ✔ ✔
PCD:AmpCh/LoadMon/LowThres
h
0 500 0
x10 ohm R/W
0: 0.0 (ohm)
:
500: 50.0 (ohm)
77
Impedance
Error(High)
✔ ✔ ✔
PCD:AmpCh/LoadMon/HighImpe
dance
0 1 0
index R 0: Normal
1: Error
78
Impedance
Error(Low)
✔ ✔ ✔
PCD:AmpCh/LoadMon/LowImpe
dance
0 1 0
index R 0: Normal
1: Error
79
Measured
Impedance
✔ ✔ ✔
PCD:AmpCh/LoadMon/Impedanc
e
0 1001 0
index
(x10)
ohm R
0 : -
1 : 0.1 (ohm)
1000: 100.0 (ohm)
1001 : >100.0 (ohm)
80
Standby ✔ ✔ ✔
AMP:Power
0 1 0 index R/W 0: Standby
1: On
81
Default ✔ ✔ ✔
PCD:PS/PwOnDefault
0 1 1 index R/W
0: Always Standby
1: Keep Previous State
82
Delay ✔ ✔ ✔
PCD:PS/PwOnDelay
0 120 0 x1 sec R/W 0: 0s
:
120: 120s
83
Voltage ✔ ✔ ✔
PCD:Mains/Voltage
0 600 0
x1 V R 0: 0V
:
600: 600V
84
Current ✔ ✔ ✔
PCD:Mains/Current
0 255 0 x1 A R 0: 0A
:
255: 255A
*1: D1+A1 to ch1, D2+A2 to ch2, D3+A3 to ch3, D4+A4 to ch4
*2: ch1 to chA, ch2 to chB, ch3 to chC, ch4 to chD
*3: 25Hz,40Hz,63Hz,100Hz,160Hz,250Hz,400Hz,630Hz,1.0kHz,1.6kHz,2.5kHz,4.0kHz,6.3kHz,10.0kHz,16.0kHz,20.0kHz
Power Supply
Input Redundancy
0
0: A
1: B
2: C
3: D
0 - 3
0
0
0 - 3
0: A
1: B
2: C
3: D
0
Load Monitoring
Power On
Setting
Mains
Second
Source
Third
Source