U PDM-4210 High definition plasma monitor Moniteur plasma haute définition 2003 YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD.
011_PDM-4210_U_E 2003.12.23 23:37 ページ 1 (ブラック 版) IMPORTANT SAFETY INSTRUCTIONS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR Yamaha High Definition Plasma Monitor Our reputation has been built on the quality, performance, and ease of service of Yamaha High Definition Plasma Monitor. Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you.
011_PDM-4210_U_E 2003.12.23 23:37 ページ 1 (ブラック 版) IMPORTANT SAFETY INSTRUCTIONS Do not place any objects on the top of the monitor which may fall or cause a child to climb to retrieve the objects. 15. Monitors are designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury. 16.
011_PDM-4210_U_E 2003.12.23 23:37 ページ 2 (ブラック 版) • FCC (Federal Communications Commission) STATEMENT WARNING COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Electronics Corporation Address: 6660 Orangethorpe Avenue Buena Park, CA90620 Telephone: 714-522-9105 Fax: 714-670-0108 Type of Equipment: High Definition Plasma Monitor Model Name: PDM-4210 This device complies with Part 15 of the FCC Rules.
011_PDM-4210_U_E 2003.12.23 23:37 ページ 3 (ブラック 版) ENGLISH USER’S MANUAL Thank you very much for purchasing the Yamaha High Definition Plasma Monitor. Before using your monitor, please carefully read this manual so you will know how to operate the monitor properly. Keep this manual in a safe place. You will find it useful in the future. Notes on lnstallation Work: This product is marketed assuming that it is installed by qualifed personnel with enough skill and competence.
011_PDM-4210_U_E 2003.12.23 23:37 ページ 4 (ブラック 版) FEATURES Large-screen, high-definition plasma display panel The 42-inch color plasma display panel, with a resolution of 1024 (H) x 1024(V) pixels, creates a high-definition, large-screen (aspect ratio : 16:9) and low-profile flat display. Free from electromagnetic interferences from geomagnetic sources and ambient power lines, the panel produces high-quality display images free from color misconvergence and display distortion.
011_PDM-4210_U_E 2003.12.23 23:37 ページ 5 (ブラック 版) CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. ENGLISH This Plasma monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions.
011_PDM-4210_U_E 2003.12.23 23:37 ページ 6 (ブラック 版) CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.(continued) Be careful in handling the power cord and external connection cables. If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension to the power cord and cables. If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
011_PDM-4210_U_E 2003.12.23 23:37 ページ 7 (ブラック 版) CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.(continued) ENGLISH Note on image retention The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images.
011_PDM-4210_U_E 2003.12.23 23:37 ページ 8 (ブラック 版) CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.(continued) Precautions for the installation - Do not use makeshift pedestals and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved pedestal or legs with the fixings provided according to the instructions. - Use only with the cart, pedestal, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
012_PDM-4210_U_E 2003.12.23 17:51 ページ 9 (ブラック 版) COMPONENT NAMES Front ENGLISH Main Unit Cabinet (front frame) Panel Pedestal (option) Control panel • Adjustment buttons are located on the bottom. • The back cover is provided with indications to distinguish the adjustment buttons. Remote-control 10 receiver Indicating lamp 14 MENU button 17 • The main power switch is located at the back, on the lower surface.
012_PDM-4210_U_E 2003.12.23 17:51 ページ 10 (ブラック 版) COMPONENT NAMES (continued) Remote control POWER OFF button 14 14 POWER ON/OFF button POWER ON button 14 MUTE button 15 15 VOLUME UP/DOWN buttons VOL RGB/VIDEO buttons 15 PinP button 35 AUTO button 17 MENU button 17 RGB 1 RGB 2 MUTE VOL AV1 AV2 AV3 AV4 AUTO PinP SIZE RECALL 16 SIZE button 16 RECALL button MENU 17 RETURN button OK OK button 17 ID 17 SELECT/ADJUST buttons ID SET 17 ID SET button ID button 17 Loading Batteries 1.
012_PDM-4210_U_E 2003.12.23 17:51 ページ 11 (ブラック 版) INSTALLATION INSTRUCTIONS ENGLISH Installation • If you have purchased the model without the pedestal attached: When installing the monitor, use the optional pedestal. The pedestal has been used for the illustrations in this manual. CAUTION 10cm (4 inches) or more* • Use one of the special mount units to install this product.
012_PDM-4210_U_E 2003.12.23 17:51 ページ 12 (ブラック 版) INSTALLATION INSTRUCTIONS (continued) Read CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. and PRECAUTIONS ( carefully to ensure maximum safety before proceeding to these steps: 5 to 8 ) • Choose a safe, level location to install the product. • Install the monitor in a location with easy access to a power socket. • Make sure that the power switch of this device is turned off.
012_PDM-4210_U_E 2003.12.23 17:51 ページ 13 (ブラック 版) INSTALLATION INSTRUCTIONS (continued) ENGLISH Power Cord Connection Connect the power cord after completing all other connections. ① ② ① Connect the power cord to this device. ② Connect the power cord plug to the power outlet. (The type of plug is different from this drawing for some countries.) CAUTION • Use only the power cord provided.
013_PDM-4210_U_E 2003.12.23 17:53 ページ 14 (ブラック 版) OPERATING INSTRUCTIONS Turning Power On and Off • To turn the monitor power on, press the main power Indicating lamp Main power switch switch on the monitor main unit to ON, and then press the SUB POWER button or the ON/OFF or ON button on the remote control. • To turn the monitor power off, press the SUB POWER button or the ON/OFF or OFF button on the remote control, and then set the main power switch on the monitor main unit to OFF.
013_PDM-4210_U_E 2003.12.23 17:53 ページ 15 (ブラック 版) OPERATING INSTRUCTIONS (continued) ENGLISH Volume Adjustment The volume can be adjusted by pressing the VOL+ and VOL- buttons of the remote control (or the ▲ and ▼ volume buttons of the monitor unit). Volume setting value ▼ ▲ Volume 15 VOLUME UP/DOWN buttons INPUT SELECT button • When a button is pressed, the volume adjustment status guide will be displayed.
013_PDM-4210_U_E 2003.12.23 17:53 ページ 16 (ブラック 版) OPERATING INSTRUCTIONS (continued) RGB 1 RGB 2 MUTE VOL AV1 AV2 AV3 AV4 AUTO PinP SIZE RECALL RECALL button MENU OK SIZE button ID ID SET RECALL button SIZE button Size Switching Each time the SIZE button of the remote control or the monitor is pressed, the screen display area will change in sequence and the status will be displayed at the bottom of the screen.
013_PDM-4210_U_E 2003.12.23 17:53 ページ 17 (ブラック 版) OPERATING INSTRUCTIONS (continued) VOL AUTO button MENU button RGB 1 RGB 2 MUTE AV1 AV2 AV3 AV4 AUTO PinP SIZE RECALL ENGLISH Using the Menu Screen (On-screen display system) VOL RETURN buttons MENU SELECT/ADJUST buttons OK When the MENU button is pressed, the adjustment menu screen will be displayed; from there, PC signal adjustment and setting is possible by using the SELECT button, ADJUST button and OK button.
013_PDM-4210_U_E 2003.12.23 17:53 ページ 18 (ブラック 版) OPERATING INSTRUCTIONS (continued) PICTURE MENU MENU Picture Audio Timer Function Setup Language Select OK Set Picture Contrast Brightness Color Tint Picture Enhancement Color Temperature Color Temp.Adjust Reset Select OK Set OK Picture Contrast Brightness Color Tint Picture Enhancement Color Temperature Color Temp.
013_PDM-4210_U_E 2003.12.23 17:53 ページ 19 (ブラック 版) OPERATING INSTRUCTIONS (continued) Picture Audio Timer Function Setup Language Select OK Set Selected characters Movie Audio Mode ▲ ▲ MENU OK Audio Audio Mode Treble Bass Balance SRS TruBass Matrix Surround Perfect Volume Reset Select Set Music Speech Favorite : : : : : : : Movie + 10 – 10 0L Middle Off Off Reset Return ENGLISH AUDIO MENU R Setup hint Movie: This selects the audio mode suitable for Movies.
013_PDM-4210_U_E 2003.12.23 17:53 ページ 20 (ブラック 版) OPERATING INSTRUCTIONS (continued) FUNCTION MENU Picture Audio Timer Function Setup Language Select OK Set Screen Saver Screen Wipe Off 60Min. 5Min. 40Min. This turns the gray sidebars On/Off when watching normal mode screen size area. It is always set to Off when the monitor is powered On. It is recommended to set Black Side Panel to off to reduce the panel image retention.
013_PDM-4210_U_E 2003.12.
013_PDM-4210_U_E 2003.12.23 17:53 ページ 22 (ブラック 版) OPERATING INSTRUCTIONS (continued) LANGUAGE MENU Picture Audio Timer Function Setup Language Select OK Set MENU Language English Français Español OK Select Return Exit Select a language using the ▼ ▲ SELECT buttons and press the OK button. OTHER FEATURES Automatic Store Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
013_PDM-4210_U_E 2003.12.23 17:53 ページ 23 (ブラック 版) OTHER FEATURES (continued) ENGLISH Signal Check Changes in the signal status are displayed on the screen as they arise. Status Display When Mode Display is set to ON, the input signal is switched or when the RECALL button is pressed. RGB Action A guide is displayed for the input terminal and the horizontal and vertical sync frequency. RGB2 RGB H : 48.4kHz V : 60.1 Hz OFF When the sync signal is no longer detected.
014_PDM-4210_U_E 2003.12.23 17:56 ページ 24 (ブラック 版) IMAGE RETENTION OF PLASMA DISPLAY PANEL There are different characteristics that result in panel image retention depending on how the plasma monitor is used. Situations and effective usage methods related to ghosting are provided below. Image retention characteristics of a plasma display panel The image retention phenomenon of a plasma display panel occurs due to partial phosphor degradation arising from partial character and figure display.
014_PDM-4210_U_E 2003.12.23 17:56 ページ 25 (ブラック 版) TROUBLESHOOTING ENGLISH Symptoms That Appear to be Failures Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer. CAUTION Customer servicing can be hazardous. Point to check Symptom • No picture with the power-indicating lamp off. • Check the way the power cable is connected. • Press the power switch. See page 13 14 • The message “No Sync. Signal” or “Power Save” is displayed.
014_PDM-4210_U_E 2003.12.23 17:56 ページ 26 (ブラック 版) TROUBLESHOOTING (continued) Symptoms That Appear to be Failures (continued) Symptom • The temperature of the display panel surface is high. 26 Point to check • Plasma display panel is lighting the phosphors in the display panel by the discharge of internal radiation. In some cases, this may cause the temperature of the panel surface to increase. Please note that this is not a malfunction.
014_PDM-4210_U_E 2003.12.23 17:56 ページ 27 (ブラック 版) TROUBLESHOOTING (continued) ENGLISH Actions to Correct Abnormal Displays Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the adjustments suggested below. (only for RGB2) Symptom 1 Text displayed across the screen appears vertically streaked, with some characters blurred (figure 1). The display image appears flowing (figure 2) (RGB input).
014_PDM-4210_U_E 2003.12.23 17:56 ページ 28 (ブラック 版) PRODUCT SPECIFICATIONS Product specifications and designs are subject to change without notice. Panel Display dimensions Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm) Resolution 1024 (H) x 1024 (V) pixels Net dimensions (excluding pedestal) 1030 (W) x 636 (H) x 91 (D) mm Net weight (excluding pedestal) 34.
014_PDM-4210_U_E 2003.12.23 17:56 ページ 29 (ブラック 版) PRODUCT SPECIFICATIONS (continued) ENGLISH Signal Input (continued) DVI terminal (DVI-D) Pin Input signal Pin 1 2 3 4 5 6 7 8 9 10 T.M.D.S. Data2T.M.D.S. Data2+ T.M.D.S. Data2/4 Shield T.M.D.S. Data4T.M.D.S. Data4+ DDC Clock DDC Data No Connect T.M.D.S. Data1T.M.D.S. Data1+ 14 15 16 17 18 19 20 21 22 23 +5V Power Ground (for+5V) Hot Plug Detect T.M.D.S. Data0T.M.D.S. Data0+ T.M.D.S. Data0/5 Shield T.M.D.S. Data5T.M.D.S. Data5+ T.M.D.S.
014_PDM-4210_U_E 2003.12.23 17:56 ページ 30 (ブラック 版) PRODUCT SPECIFICATIONS (continued) Recommended Signal List (continued) With Analog RGB signal input (RGB2 input) Signal mode No. Horizontal frequency (kHz) Dot clock frequency (MHz) 70.08 59.94 31.47 31.47 25.18 25.18 864 X 480 59.94 31.47 34.
015_PDM-4210_U_E 2003.12.
015_PDM-4210_U_E 2003.12.24 18:37 ページ 32 (ブラック 版) Optional Video Unit Function Additional functions when the optional video unit is installed are as follows: ( 32 ∼ 43 ) INSTALLATION INSTRUCTIONS Connecting to a Video Imaging Device (1) Make sure that the power switch of the monitor is turned off. (2) Make sure that the power switch of the imaging device is turned off.
015_PDM-4210_U_E 2003.12.24 18:37 ページ 33 (ブラック 版) OPERATING INSTRUCTIONS ENGLISH VOL RGB 1 RGB 2 MUTE AV1 AV2 AV3 AV4 AUTO PinP SIZE RECALL RGB/VIDEO buttons VOL SIZE button MENU INPUT SELECT button OK SIZE button Input Switching ・ Input can be switched by pressing the AV1, AV2, AV3, AV4, RGB1 or RGB2 buttons of the remote control. ・ Input can be switched in the sequence of AV1 → AV2 → AV3 → AV4 → RGB1 → RGB2 by pressing the INPUT SELECT button of the monitor.
015_PDM-4210_U_E 2003.12.24 18:37 ページ 34 (ブラック 版) Vertical picture position can be adjusted for [Panoramic], [Zoom] and [Cinema] mode as follows. 1. Press the SIZE button and SELECT buttons during picture size display. 2. The position display will appear. 3. The adjustment range of each picture size is as shown below. [Panoramic] - 12 to + 12 [Zoom] and [Cinema] - 31 to + 31 4. When 1080i/50 or 1080i/60 component signal is received, vertical position can be adjusted only one step up.
015_PDM-4210_U_E 2003.12.24 18:37 ページ 35 (ブラック 版) OPERATING INSTRUCTIONS (continued) ENGLISH Displaying MULTI PICTURE If the PinP button on the remote control is pressed MULTI PICTURE will display. Activating the P-in-P mode from the RGB input screen Pressing the PinP button once will display 2 pictures. RECALL button VOL PinP button RGB 1 RGB 2 MUTE AV1 AV2 AV3 VOL RECALL button AV4 • This mode can be available from RGB1(DVI-PC) and RGB2(RGB) input.
015_PDM-4210_U_E 2003.12.
015_PDM-4210_U_E 2003.12.24 18:37 ページ 37 (ブラック 版) OPERATING INSTRUCTIONS (continued) ▲ ▲ Selected characters Day Picture Mode Setup hint Day: This setting is best for very bright ambient lighting. Night: This setting is for normal lighting conditions. Night Adjust for maximum visibility to suit the ambient brightness. This can be adjusted further till [+40] by pressing and holding cursor button at [+31]. The color for [+32] to [+40] numbers will change from white to magenta.
015_PDM-4210_U_E 2003.12.24 18:37 ページ 38 (ブラック 版) OPERATING INSTRUCTIONS (continued) Selected characters ▲ ▲ PICTURE MENU (continued) Off Color Management Magenta Turn On when the original balance of each color is required to adjust to suit user preferences. On Magenta is weakened. Magenta is strengthened. Red is weakened. Red is strengthened. Yellow Yellow is weakened. Yellow is strengthened. Green Green is weakened. Green is strengthened. Cyan Cyan is weakened.
015_PDM-4210_U_E 2003.12.
015_PDM-4210_U_E 2003.12.24 18:37 ページ 40 (ブラック 版) OPERATING INSTRUCTIONS (continued) Selected characters ▲ ▲ SETUP MENU (continued) Setup hint Audio Input Stereo AV1 L/Mono This should correspond to the audio signal from the equipment that is connected to the AV1 audio input terminal. If the signal is monaural audio, set this to L/Mono.
015_PDM-4210_U_E 2003.12.24 18:37 ページ 41 (ブラック 版) TROUBLESHOOTING ENGLISH Symptoms That Seemingly Appear to be Failures Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer. CAUTION Customer servicing can be hazardous. Symptom • The screen becomes dark and the images cannot be seen during VCR special playback (fast forward, rewind).
015_PDM-4210_U_E 2003.12.24 18:37 ページ 42 (ブラック 版) PRODUCT SPECIFICATIONS (continued) Signal Input RGB terminal (D-sub 15-pin connector) Pin Input signal 1 R (PR/CR) 2 G or sync on green (Y) 3 B (PB/CB) 4 No connection 5 No connection 6 R.
015_PDM-4210_U_E 2003.12.24 18:37 ページ 43 (ブラック 版) PRODUCT SPECIFICATIONS (continued) ENGLISH Recommended Signal List With Digital RGB signal input (RGB1 input) Signal mode No. 1 Signal Name Resolution Horizontal Dot clock Setup Menu Condition Vertical frequency frequency frequency DVI-PC DVI-STB (kHz) (MHz) (Hz) Remarks 640 X 400 70.08 31.47 25.18 ○ 640 X 480 59.94 31.47 25.18 ○ 864 X 480 59.94 31.47 34.24 ○ 4 640 X 480 72.81 37.86 31.50 ○ 5 640 X 480 75.00 37.50 31.
U PDM-4210 High definition plasma monitor Moniteur plasma haute définition 2003 YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD.
ConnectionGuide_U.qxd 2003.12.12 19:32 ページ 1 (ブラック 版) Basic connection to an AV Receiver PDM-4210 Monitor rear panel High Definition Plasma monitor PDM-4210 U.S.
ImageRetention-Note.qxd 2003.12.12 19:17 ページ 1 (ブラック 版) Examples of Image Retention Exemples de Rétention d’Image Beispiele für Bildspeichereffekte Exempel på kvarstående bilder Ejemplos de Retención de Imagen English Image Retention Image Retention can be an issue for all plasma monitors, however if you follow the simple guidelines listed below, you can enjoy many years of viewing. YAMAHA has included a number of features in our range of plasma monitors which help to reduce image retention.
Video-Note 2003.12.12 19:29 ページ 1 (ブラック 版) NOTE The video unit (PTB-4210) is included as standard equipment with this model ; therefore, descriptions of “Optional Video Unit Function” in this text can be used as is. REMARQUES L’appareil vidéo (PTB-4210) est fourni en standard avec ce modèle ; les explications des opérations relatives à la function de la vidéo dans ce texte peuvent donc être utilisées telles quelles.
PDS-242_E 2003.12.11 11:23 1 To ensure correct usage WARNING ■ Always use at least two people to perform installation work. Injury could result from dropping heavy objects. ■ Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the plasma monitor falls.
PDS-242_E 2003.12.11 11:23 2 Parts Configuration Chart Assembly Method Included in the parts package Prepare a phillips screwdriver before proceeding with assembly. Assembling the pedestal Attaching the Plasma Monitor to the pedestal 1. Insert the support into the pedestal base and secure it in position by tightening four M5 x 20 screws from the bottom. 2. Insert the pedestal support into the square holes on the bottom of the plasma monitor.
PDS-242_E 2003.12.11 11:23 1 To ensure correct usage WARNING ■ Always use at least two people to perform installation work. Injury could result from dropping heavy objects. ■ Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the plasma monitor falls.