User Manual

PM1D System Software V1.5 Supplementary Manual
72
1 MIDI PORT Tx/Rx (MIDI transmit/receive port)
Selects the MIDI port that will transmit MIDI mes-
sages (Tx) and the MIDI port that will receive MIDI
messages (Rx). You can select the console or engine
port.
• When using the PM1D system in Dual Console
mode, you can select console 1 or 2.
• When using the PM1D system in Mirror mode,
and the engine is selected, the MIDI port of the
currently-enabled engine will be selected auto-
matically. (This is an improvement from the pre-
vious version.)
2 PROGRAM CHANGE Tx/Rx (PROGRAM
CHANGE transmission/reception)
Switches PROGRAM CHANGE transmission (Tx)
or reception (Rx) on/off.
3 PROGRAM CHANGE MIDI MODE (PROGRAM
CHANGE MIDI mode)
As the PROGRAM CHANGE transmission/recep-
tion mode, you can select either Multi mode (use
MIDI channels 1–16 for transmission and reception)
or Single mode (use only a single MIDI channel for
transmission and reception).
For details, refer to the CS1D Reference Manual
(Software), page 30, item 3.
4 OMNI
If Single mode is selected, turning this button on will
allow program change messages of all MIDI channels
to be received. In Multi mode, this button has no
effect.
5 BANK ON/OFF (Bank select on/off)
If Single mode is selected, turning this button on will
allow bank select messages to be received, increasing
the number of parameters that respond to program
change messages. In Multi mode, this button has no
effect.
6 PROGRAM CHANGE ECHO (PROGRAM
CHANGE echo output)
If this button is on, program change messages
received from the MIDI IN connector will be echoed
from the MIDI OUT connector.
Hint
2–6 are identical to the functions of the same
name in the MIDI PGM CHANGE screen of previ-
ous versions.
7 CONTROL CHANGE Tx/Rx (CONTROL CHANGE
transmission/reception)
Switches CONTROL CHANGE transmission (Tx) or
reception (Rx) on/off.
8 CONTROL CHANGE MIDI MODE (CONTROL
CHANGE MIDI mode)
Selects one of the following as the CONTROL
CHANGE transmission/reception mode.
• MULTI (Multi mode)
CONTROL CHANGE on MIDI channels 1–16 will
be used simultaneously to control the event (param-
eter) assigned in the parameter list at the right side of
the screen and the parameters of the fifteen NRPN
numbers that follow it. When the console is used to
edit the corresponding parameter or any parameter
of the fifteen NRPN numbers that follow it, a CON-
TROL CHANGE message will be transmitted on
MIDI channel 1–16.
• SINGLE (Single mode)
When a CONTROL CHANGE is received on the
MIDI channel selected by the Rx knob (A), the
parameter assigned in the parameter list at the right
of the screen will be edited.
When the console is used to edit the corresponding
parameter, a control change message will be trans-
mitted on the MIDI channel selected by the Tx knob
(0).
9 NRPN Tx/Rx (NRPN transmission/reception)
Switches NRPN transmission (Tx) or reception (Rx)
on/off. This can be used simultaneously with CON-
TROL CHANGE transmission and reception. In this
case, operation will be as follows.
• CONTROL CHANGE / NRPN reception is on
Parameters to which CONTROL CHANGE or
NRPN reception (or both) is assigned will respond.
• CONTROL CHANGE / NRPN transmission is on
When you operate a parameter to which either
CONTROL CHANGE or NRPN (not both) is
assigned, the corresponding message will be trans-
mitted.
When you operate a parameter to which both CON-
TROL CHANGE and NRPN are assigned, only the
CONTROL CHANGE message will be transmitted.
1
3
8
4
5
6
2
7
9