PM1D System Software V1.
Contents New functionality in system software V1.4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Digital gain for input channels / insert inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Digital gain added to 2TR IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
New functionality in system software V1.4 Thank you for purchasing the CS1D. This booklet explains the functionality that was added or changed in version 1.4 of the PM1D software. New functionality in system software V1.4 The following functionality and specifications have been added in version 1.4 of the PM1D system software.
PM1D Manager for Windows Operating manual ■ If a digital I/O card (MY card) is assigned ■ If a GEQ output is assigned Digital gain Digital gain Digital gain can be used to adjust the input sensitivity in a range of +10 dB– –20 dB (the knob will not turn any further to the right beyond –20 dB).
Digital gain for input channels/insert inputs If 2TR IN is assigned to an input channel/insert input, the gain settings of the 2TR IN screen and the HA/INSERT screen will be linked. These settings cannot be set to different positions. The digital gain of an input channel/insert input to which 2TR IN is assigned will not be saved in the scene memory. Hint Settings for the digital gain of an input card are saved in the unit library.
PM1D Manager for Windows Operating manual Digital gain added to 2TR IN Digital gain has been added to the six 2TR IN inputs, allowing you to adjust the input sensitivity in the digital domain. The sensitivity of the signal that is input to each 2TR IN can be adjusted independently for L and R. In conjunction with this, the display in the 2TR IN screen (MON/CUE function) has changed as follows. Hint Digital gain is valid even if ANALOG is selected as the source for 2TR IN 1 or 2TR IN 2.
BALANCE control for input channels/ST IN channels ■ VARI type MIX bus If a VARI type MIX bus is paired, the PAN parameter of the MIX bus will change to a BALANCE parameter. (A BAL knob will be displayed instead of a PAN knob in the PAN/ROUTING function CH to MIX screen.) In addition, if the VARI PAN LINK button is on for either of these two channels, the MIX bus BAL knob will be linked with the STEREO bus BAL knob.
PM1D Manager for Windows Operating manual Hint Even if the BALANCE button is on, the signal that is sent from those input channels to a FIX type MIX bus will not be affected if the FIXED MIX PAN button is turned off for both channels. In addition, the operation will change as follows if the PAN MODE “BALANCE” button is on.
Temporary monaural setting for paired input channels/ST IN channels Value of the BALANCE parameter PAN PAN R Always lit Odd-numbered (L) channel Always lit Even-numbered (R) channel L ■ Set to L-MONO The channels will remain paired, but the signal will temporarily become a monaural signal containing only the odd-numbered channel.
PM1D Manager for Windows Operating manual Even if L-MONO or R-MONO is selected, you can edit the parameters of the channel that was forced off. (However, the [ON] switch will be fixed at Off until you defeat the L-MONO or R-MONO setting, and cannot be changed.) A new preference setting [L,R-MONO SELECT ON PANEL] has been added to the UTILITY function PREFERENCE screen, allowing you to switch to the LR-MONO setting from the front panel.
