User Manual
Table Of Contents
- Hinweise zur Verwendung dieses Referenzhandbuchs
- Inhalt
- Funktionsschema
- SELECTED-CHANNEL-Bereich
- Kanalzüge
- Routing der Ein- und Ausgänge
- Eingangskanäle
- Signalfluss für Eingangskanäle
- Angabe von Kanalname, Symbol und Kanalfarbe
- Einstellungen für den Eingangsverstärker (HA; Head Amp)
- Senden eines Signals von einem Eingangskanal zum STEREO/MONO-Bus
- Hinzugefügte Pan-Funktion (nur für monaurale Eingangskanäle)
- Senden eines Signals von einem Eingangskanal zu einem MIX/MATRIX-Bus
- Kanalnamenanzeige
- Korrigieren der Eingangsverzögerung zwischen Kanälen (Input Delay)
- Surround-Ausgang für Eingangskanäle
- Bedienungsvorgänge für die Kanal-Library
- OUTPUT-Kanäle
- Signalfluss für Ausgangskanäle
- Angeben von Kanalname, Symbol und Kanalfarbe
- Senden von Signalen von den MIX-Kanälen zum STEREO/MONO-Bus
- Signale von MIX-Kanälen und STEREO/MONO- Kanälen an MATRIX-Busse senden
- Korrigieren der Verzögerung zwischen Kanälen (Output Delay)
- Verwenden der PORT-TO-PORT-Funktion
- Bedienungsvorgänge für die Kanal-Library
- EQ und Dynamik
- Channel Job
- Szenenspeicher
- Speichern und Aufrufen von Szenen
- Szenenspeicher bearbeiten
- Einsatz der Funktion „Global Paste“ (Globales Einfügen)
- Verwenden der Focus-Recall-Funktion
- Verwenden der Fade-Funktion
- Ausgabe eines Steuersignals an ein externes Gerät in Kombination mit einem Szenen-Abruf (GPI OUT)
- Wiedergeben einer mit einem Szenenabruf verknüpften Audiodatei
- Verwenden des Preview-Modus (Vorschau)
- Monitor- und Cue-Funktionen
- Talkback und Oszillator
- Pegelanzeigen
- Grafischer EQ, Parametrischer EQ, Effekte und Premium Rack
- I/O-Geräte und externe Eingangsverstärker
- Verwenden eines I/O-Geräts
- Fernbedienen eines Geräts der R-Baureihe
- Hinzugefügte HA-Steuerungsfunktion für Geräte anderer Hersteller
- Fernbedienen eines Verstärkers
- Fernbedienen eines WIRELESS-Geräts
- Einsatz eines externen Eingangsverstärkers
- Fernbedienen eines externen Eingangsverstärkers
- Bedienen eines internen Eingangsverstärkers
- MIDI
- Recorder
- Informationen zum USB-Recorder
- Zuweisen von Kanälen zu den Ein-/Ausgängen des Recorders
- Audio-Aufnahme auf einem USB-Flash-Laufwerk
- Wiedergabe von Audiodateien von einem USB- Flash-Laufwerk
- Bearbeiten der Titelliste
- Aufnahme und Wiedergabe mit Hilfe von DAW- Software auf dem Computer
- Verwenden des QL-Pults mit Nuendo Live
- Setup (Einrichtung)
- Der SETUP-Bildschirm
- Benutzereinstellungen
- Einstellungen
- USER-DEFINED-Tasten
- Funktionen, die USER-DEFINED-Tasten zugewiesen werden können
- USER-DEFINED-Drehregler
- Funktionen, die benutzerdefinierten USER-DEFINED-Drehregler
- Custom Fader-Bank
- Pultsperre
- Speichern und Laden von Setup-Daten auf und von einem USB-Flash-Laufwerk
- Hinzugefügte Funktion zum erneuten Mounten von USB-Flash-Laufwerken
- Wordclock- und Slot-Einstellungen
- Verwenden von Kaskadenverbindungen
- Grundlegende Einstellungen für MIX-Busse und MATRIX-Busse
- Ein-/Ausschalten der gesamten Phantomspannungsversorgung
- Einstellen der Helligkeit des Touchscreens, der LEDs, der Kanalnamen-Displays und der Pultbeleuchtung
- Datum und Uhrzeit der eingebauten Uhr einstellen
- Einstellen der Netzwerkadresse
- Einrichten des Dante Audionetzwerks
- Dante-Gerätesperre
- Unterstützung für Dante Domain Manager
- Verwenden des GPI (General Purpose Interface)
- Hilfefunktion
- Sonstige Funktionen
- Initialisieren des Geräts auf die Werksvoreinstellungen
- Einstellen des Ablesepunkts des Touchscreens (Kalibrierungsfunktion)
- Einstellen der Fader (Kalibrierungsfunktion)
- Feineinstellen der Ein-/Ausgangsverstärkung (Kalibrierungsfunktion)
- Einstellen der LED-Farbe (Kalibrierungsfunktion)
- Einstellen der Helligkeit des Kanalnamen-Displays
- Einstellen des Kontrasts des Kanalnamen-Displays
- Initialisieren der Einstellungen des Dante- Audionetzwerks
- Geänderte Vorgehensweise beim Aktualisieren von NAME-SUB-CPU-Firmware
- Hinzugefügte Aktualisierungsfunktion für Dante-Firmware
- Warn- und Fehlermeldungen
- Index
- Data List
Data List
14
REV+CHORUS
One input, two output reverb and chorus effects in parallel.
REVCHORUS
One input, two output reverb and chorus effects in series.
REV+FLANGE
One input, two output reverb and flanger effects in parallel.
REVFLANGE
One input, two output reverb and flanger effects in series.
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
REV/CHO 0–100%
Reverb and chorus balance
(0% = all reverb, 100% = all chorus)
HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05–40.00 Hz Modulation speed
AM DEPTH 0–100% Amplitude modulation depth
PM DEPTH 0–100% Pitch modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
REV.BAL 0–100%
Reverb and chorused reverb balance
(0% = all chorused reverb, 100% = all reverb)
HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05–40.00 Hz Modulation speed
AM DEPTH 0–100% Amplitude modulation depth
PM DEPTH 0–100% Pitch modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
REV/FLG 0–100%
Reverb and flange balance
(0% = all reverb, 100% = all flange)
HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
FB. GAIN –99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
REV.BAL 0–100%
Reverb and flanged reverb balance
(0% = all flanged reverb, 100% = all reverb)
HPF THRU, 21.2 Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
FB. GAIN –99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ