User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Graphic EQ, Parametric EQ, effects, and Premium Rack
V5 Reference Manual
135
5 FLAT button
Returns all bands of the currently-selected GEQ to 0 dB.
6 GEQ ON/OFF button
Switches the currently-selected GEQ on or off.
7 RTA button
Turn this button on to overlay a frequency response graph on the EQ.
8 HOLD button
Press this button to hold the peak of the graph that displays RTA.
9 OFFSET gain knob
If a frequency is at a low level, its analysis results might not appear clearly in a graph.
The addition of offset gain allows better visibility in graphs for such results. You can
adjust this gain from 0dB to +30dB.
NOTE
The value for this parameter is applied identically to the RTA METER window, HPF/EQ window,
GEQ window, and PEQ window.
Using the 31BandGEQ
You will use the Channel Strip section’s faders 1–8 and [ON] keys to control the 31BandGEQ.
NOTE
• When a fader in the Channel Strip section is set to the center (flat) position, the corresponding
[ON] key indicator will turn off. This indicates that the corresponding band is not being modified.
If you raise or lower the fader even the slightest amount, the [ON] key will light, indicating that this
band has been modified. If you press a lit [ON] key to make it go dark, the corresponding band
will immediately return to the flat state.
If you press the [ON] key once again, the value that was modified is shown. However, please note
that if the [ON] key for this band is off and if you press the [ON] key for the fader of a different
frequency band, the adjusted gain value will be canceled and will return to ±0dB.
• If you switch the display to a different screen or rack, the fader assignments in the Channel Strip
section will forcibly be defeated. However if you once again display the same rack, the group of
bands you had previously been controlling will automatically be assigned to the faders.
• When you close the GEQ window, the buttons in the FADER ASSIGN field automatically turn off.
STEP
1. In the GEQ field or the EFFECT field rack, press the rack container in which you
mounted the 31BandGEQ.
2. Press the GEQ ON/OFF button to turn the 31BandGEQ on.
3. Press one of the buttons in the FADER ASSIGN field to select the group of bands you
will control.
4. Use the faders in the Channel Strip section to adjust the selected band.
5. When you’ve finished making settings, turn off the buttons in the FADER ASSIGN
field.