User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Monitor and Cue functions
Reference Manual
109
NOTE
• The cue signal is sent to the monitor output and PHONES Out jacks regardless of whether the
CUE OUTPUT button is on or off. However, the cue signal will no longer be sent to monitor output
if CUE INTERRUPTION is turned off. The cue signal is always sent to the PHONES Out jack,
regardless of the CUE INTERRUPTION setting.
• When using the MIX/MATRIX bus select buttons in the SENDS ON FADER window, you can
press the selected button once again to turn on cue for the corresponding MIX/MATRIX channel
(page 40).
• If you want cue operations and channel select operations to be linked, open the USER SETUP
window, choose the PREFERENCE tab, and then turn on [CUE][SEL] LINK (page 206).
• You can also assign the function of the CLEAR CUE button to a USER DEFINED key
(page 208).
• If PHONES LEVEL LINK (page 102) in the MONITOR screen is ON, the cue signal level when
monitoring through headphones can be adjusted using both the MONITOR LEVEL knob and the
PHONES LEVEL knob.
• To adjust the level to the output destination port for the cue signal, adjust the gain of the output
port that is patched to it.
• If you turn on the [CUE] key, the cue output level is indicated. The upper part of the cue meter
shows an abbreviation indicating the currently-on cue group or cue button. The abbreviations
displayed for the cue meters have the following meaning.
• If CUE is set to 2 channels, the CUE meter is displayed as shown below.
MONITOR screen
The CUE field on the MONITOR screen enables you to check the current cue settings, and
turn cue on or off.
1 CUE display button
When you press this button, the CUE window will appear, in which you can make
detailed cue settings.
IN INPUT CUE group
DCA DCA CUE group
OUT OUTPUT CUE group
EFFECT
CUE button in the EFFECT and PREMIUM RACK windows
(Other CUE groups)
KEY IN
KEY IN CUE button in the DYNAMICS1 window
(Other CUE groups)
REC/PB
RECORDER INPUT CUE button or PLAYBACK OUT CUE button
(Other CUE groups)
CUE meter
CUE A&B
Only CUE A
Only CUE B
1
5
6
2 43