User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Recorder
Reference Manual
186
5 REC RATE button
Switches the recording rate.
You can choose 96 kbps, 128 kbps, or 192 kbps. Higher bit rates will improve the audio
quality, but will increase the size of the data.
NOTE
The word clock rate at which the QL series console is currently operating will automatically be
selected as the sampling rate for the audio file.
6 Display switch buttons
Switches between displaying and hiding the RECORDER INPUT/PLAYBACK OUTPUT
fields at the bottom of the song list.
7 REW button
Moves the playback point to the beginning of the current song and stops playback. If
the playback point is already at the beginning, the point will move to the beginning of
the preceding song that has been selected for playback.
If the playback point is not at the beginning of the current song, holding down this
button for two seconds or longer will rewind the playback point.
If you operate this button during playback, playback will resume from the point at which
the button was released.
8 STOP button
The recorder will change from play/record/recording-standby mode to stop mode.
9 PLAY button
Changes the recorder mode as follows.
Stop mode
Playback mode, then starts playback from the beginning of the current
song.
Playback mode
Playback-pause mode
Playback pause mode
Playback mode, then starts playback from the paused point.
Recording standby mode
Recording mode
Recording mode
Recording-pause mode
Recording-pause mode
Recording mode, then starts recording from the paused point.
0 FF button
Moves the playback point to the beginning of the next song that is marked with a PLAY
check symbol.
If you hold down this button for two seconds or longer, fast-forward will occur.
If you operate this button during playback, playback will resume from the point at which
the button was released.
A REC button
Places the recorder in recording standby mode.
The pause indicator of the PLAY/PAUSE ( ) button will light.
NOTE
You can also assign the function of each button to a USER DEFINED key (page 208).
Directory structure of a USB flash drive
When you connect a USB flash drive to the USB connector, a YPE folder and a SONGS folder
within that YPE folder will be created automatically in the root directory of the USB flash drive.
The files created by recording operations will be saved in the above SONGS folder, or in the
currently-selected folder below that level.
Song
(audio file)
Songs folder
YPE folder
Root directory