User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Channel Strip section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon, and channel color
- Making HA (Head Amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- Signal flow for output channels
- Specifying the channel name, icon, and channel color
- Sending signals from MIX channels to the STEREO/ MONO bus
- Sending signals from MIX channels and STEREO/ MONO channels to MATRIX buses
- Correcting delay between channels (Output Delay)
- Using the PORT TO PORT function
- Channel library operations
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, effects, and Premium Rack
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Custom fader bank
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Remount function to USB flash drives
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Setting up the Dante audio network
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the LED color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- MIDI Data Format
- Input/Output Specifications
- Electrical characteristics
- Mixer Basic Parameters
- Pin Assignment Chart
- MIDI Implementation Chart
Recorder
Reference Manual
193
Transport field
Here you can operate the transport of Nuendo Live.
7 GO TO PROJECT START button
Returns the location to the start of the project.
8 GO TO PREVIOUS MARKER button
Returns the location to the previous marker.
9 GO TO NEXT MARKER button
Advances the location to the next marker.
0 GO TO PROJECT END button
Advances the location to the end of the project.
A CYCLE button
Turns repeat on/off for the project.
B STOP button
Stops playback/recording of the project.
C PLAY button
Starts playback of the project.
D RECORD button
Starts/stops recording of the project.
E EASY RECORDING button
Immediately starts recording on all tracks.
When you press this, the location will move to the last-recorded position, all tracks will
be set to record mode, recording will begin, the record panel will be displayed, and the
panel will be locked. The recording will be started retrospectively.
(Initial setting: 10 seconds)
F Record lock button
Turns recording status lock on/off. This prevents recording from being accidentally
stopped during recording.
G DVS information display
Shows the device label of the selected DVS.
H ADD MARKER button
Adds a marker to the project at the current location.
I RECALL LINK button
Specifies whether a marker will be created when you recall a scene. If this function is
turned on, the button will be lit.
NOTE
Transport functions can also be controlled from USER DEFINED keys (page 208).
Specifying DVS or Dante Accelerator
Before you proceed, use DANTE SETUP to specify the I/O devices that will be mounted. For
details, refer to “Mounting an I/O device on the Dante audio network” on page 240.
NOTE
• You can specify either DVS or Dante Accelerator in the NUENDO LIVE SETUP window.
• However, do not select the same DVS or Dante Accelerator from multiple QL series consoles.
NUENDO LIVE SETUP window
In this window, specify the device that the console will use for communication when working
with Nuendo Live.
STEP
1. In the Nuendo Live screen, press the NUENDO Live SETUP button.
2. In the NUENDO LIVE SETUP window, press the setting method select button.
3. Use the [TOUCH AND TURN] knob to make settings.
4. When you have finished making settings, press the OK button to close the window.
1