User Manual

Setup
Reference Manual
211
EFFECT
BYPASS
EFFECT RACK 1–8 —
PREMIUM RACK 1A —
PREMIUM RACK 1B —
:—
PREMIUM RACK 8A —
PREMIUM RACK 8B —
FADER BANK
SNAPSHOT
——
Takes a snapshot of the bank settings (hold
down the key for two seconds or longer), or
displays the last bank for which a snapshot was
taken (press and release the key within two
seconds).
GAIN KNOB
FUNCTION
LATCH —
Toggle the function of the GAIN knob (ANALOG
GAIN/DIGITAL GAIN). Lit when DIGITAL GAIN is
selected. It goes OFF when the bank is switched.
UNLATCH —
Assign the function of the GAIN knob (ANALOG
GAIN/DIGITAL) to DIGITAL GAIN only while held
down.
* However if the GAIN KNOB FUNCTION is
switched to DIGITAL GAIN in the PREFERENCE
screen etc., this will remain lit until the next time
it is pressed. It goes OFF when the bank is
switched.
GEQ FREQ
BANK
INC
—
Adds or removes a frequency bank in the GEQ
EDIT screen.
DEC
GPI OUT
LATCH
PORT1–PORT5
Toggle the GPI OUT function. Lit when active.
UNLATCH Make GPI OUT active only while pressed.
HELP — —
Opens and closes the HELP window. Operating
the controllers on the panel (excluding faders),
or controllers on the screen, while holding down
this key will display the related information.
HOME
SELECTED CH VIEW — Displays the SELECTED CHANNEL VIEW screen.
OVERVIEW — Displays the OVERVIEW screen.
TOGGLE —
Each press of the key will alternately display the
SELECTED CHANNEL VIEW screen and the
OVERVIEW screen.
METER
PEAK HOLD ON —
Turns the meter’s peak hold function on/off. Lit
when on.
SURROUND METER —
For Surround mode, toggle between the
content to be shown in meters displayed in the
Function Access Area. The lamp is off for MIX 1-
6, and on for SURROUND MONITOR.
MIDI
PROGRAM CHANGE PGM 1–128
Transmit the corresponding MIDI message.
For NOTE ON, it goes OFF when the bank is
switched.
CONTROL CHANGE
CC 1–31, 33–95,
102–119
NOTE ON
NOTE ON C-2 (0)
:
NOTE ON G 8 (127)
FUNCTION PARAMETER 1 PARAMETER 2 Explanation
MONITOR
OUTPUT — Switch the monitor output on/off.
SELECTED CH ASSIGN —
While holding down this key, press the SEL key
of a MIX or MATRIX channel to switch the
assignment on/off. During this time, the [SEL]
LED will be lit if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching. It goes OFF when the
bank is switched.
MONITOR
DIMMER ON —
Enable the dimmer and attenuate the monitor
signal.
SOURCE SELECT
STEREO L/R
Recall the selected signal to the monitor.
MONO (C)
LCR
PB OUT
*5)
DEFINE
SURROUND SOURCE
SELECT
*6)
Recall the selected signal to the surround
monitor.
SURROUND
DOWNMIX
STEREO, MONO
When this function is off (the lamp is off),
the setting returns to 5.1 monitor.
SURROUND SPEAKER
SOLO
When this function is on (the lamp is on),
the SURROUND MONITOR screen opens.
When this function is off (the lamp is off),
the SURROUND MONITOR screen closes.
L, R, C, Ls, Rs, LFE
This functionality is the same as the
SPEAKER MUTE function in the
SURROUND MONITOR screen. When the
SOLO button is on, it functions as a SOLO
key.
MUTE
MASTER
MUTE GROUP 1
— Switch MUTE GROUP MASTER on/off.:
MUTE GROUP 8
ALL MUTE —
Turns all MUTE GROUP MASTER settings on/off
together.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation